Control Connections - Extron electronics MKP 3000 User Manual

im Vertrieb von
Installation, cont'd
Switch RS-232 port — If desired, connect a cable between this
5
3-pole, 3.5 mm, RS-232 connector and a matrix switcher
(figure 2-8).
MAAP Opening (MKP 3000 MAAP) — The MKP 3000 MAAP
6
has a space that allows the installation of up to four optional
mini architectural adapter plates (MAAPs). This space is
typically filled by an optional four space MKP 10 MAAP
keypad, but a variety of other adapter plates are also available.
Blank plates (two single-space and one double-space plate) are
included with the MKP to cover unused spaces. The
MKP 10 MAAP or other MAAP(s) must be ordered separately.
They also should be attached to the faceplate and cabled before
the MKP is installed in the wall or furniture. See "Mounting the
MKP 10 MAAP," later in this chapter.

Control connections

The MKP has two RS-232 ports (a Host port [
port [ ]) and an LAN (Ethernet) port (
5
An MKP control panel can be directly cross-connected to any
Extron matrix switcher through the switcher's RS-232 port (see
figure 2-13, later in this chapter, for pin assignments for the
RS-232 cable). A control system or host computer can be
connected via the MKP's host RS-232 port.
MKP 3000
MKP 3000
I/O
SELECT
Extron
MKP 3000 Extron
MKP 3000
I/O
Ethernet
SELECT
Extron
MKP 3000
Extron
MKP 3000
Figure 2-9 — MKP connection using the RS-232 port
www.camboard.de
2-10 MKP 3000 Remote Control Panel • Installation
] and a Switch
4
).
1
Matrix Switcher
I
1 2 3 4 5 6 7 8 9 10 11 12 N
P
I/O U
13 14 15 16 17 18 19 20 21 22 23 24 T
S
CONTROL I/O
SELECT
O
1 2 3 4 5 6 7 8 9 10 11 12 U
T
P
U
13 14 15 16 17 18 19 20 21 22 23 24 T
S
MAV 2400 SERIES SWITCHER
MKP 3000
Switcher
RS-232 Port
I/O
VOLUME
Ethernet
MKP 3000
MKP 3000
Host
RS-232 Port
I/O
SELECT
MKP 3000
Control
System
Tel. 07131 911201
Fax 07131 911203
CAMBOARD Electronics
Additional MKPs can be connected to the matrix switcher
through the MKP that is RS-232 connected (the primary MKP).
The additional (secondary) MKPs are connected to the primary
MKP via the primary MKP's Ethernet port. Figure 2-9 shows an
example of this type of configuration.
An MKP control panel can be directly connected to any
Ethernet-enabled matrix switcher via the switcher's Ethernet
port (figure 2-10) using a TP (network) cable that is wired as a
crossover cable (see "TP cable termination," later in this chapter,
to properly wire the cable).
1 2 3 4 5 6 7 8 9 10 11 12 I
N
P
U
I/O
LAN Port 13 14 15 16 17 18 19 20 21 22 23 24 T
S
CONTROL
SELECT
O
1 2 3 4 5 6 7 8 9 10 11 12 U
T
Crossover P
13 14 15 16 17 18 19 20 21 22 23 24 U
T
S
Cable MAV 2400 SERIES SWITCHER
Extron
MKP 3000
Matrix Switcher
MKP 3000
Figure 2-10 — Direct MKP connection using the LAN
port
Any number of control panels can be connected as part of a
network to any Ethernet-enabled matrix switcher via the
switcher's Ethernet port (figure 2-11). All TP cables in this
example are wired as patch (straight-through) cables.
MKP 3000
MKP 3000
I/O
I/O
SELECT
SELECT
Extron
MKP 3000
Extron
MKP 3000
MKP 3000
I/O
Ethernet
SELECT
Ethernet
Extron
MKP 3000
I/O
SELECT
Extron
MKP 3000
MKP 3000
Figure 2-11 — Network MKP connection using the
LAN port
ce-info@camboard.de
MKP 3000 Remote Control Panel • Installation
I/O
Matrix Switcher
I
1 2 3 4 5 6 7 8 9 10 11 12
N
P
U
T
13 14 15 16 17 18 19 20 21 22 23 24 S
CONTROL I/O
O
1 2 3 4 5 6 7 8 9 10 11 12
U
T
P
U
13 14 15 16 17 18 19 20 21 22 23 24 T
S
MAV 2400 SERIES SWITCHER
Switcher
RS-232 Port
I/O
VOLUME
MKP 3000
MKP 3000
Host
RS-232 Port
Control
System
2-11