Jeep cherokee 2000 Service Manual page 128

3 - 92 194 RBI AXLE
ADJUSTMENTS (Continued)
Compensation for
achieved with select shims. The shims are placed
under the inner pinion bearing cone (Fig. 65).
If a new gear set is being installed, note the depth
variance etched into both the original and replace-
ment pinion gear. Add or subtract the thickness of
the original depth shims to compensate for the differ-
ence in the depth variances. Refer to the Depth Vari-
ance charts.
Note where Old and New Pinion Marking columns
intersect. Intersecting figure represents plus or
minus amount needed.
Note the etched number on the face of the drive
pinion gear (–1, –2, 0, +1, +2, etc.). The numbers rep-
resent thousands of an inch deviation from the stan-
dard. If the number is negative, add that value to the
required thickness of the depth shim(s). If the num-
ber is positive, subtract that value from the thickness
of the depth shim(s). If the number is 0 no change is
necessary. Refer to the Pinion Gear Depth Variance
Chart.
Original Pinion
Gear Depth
Variance
+4 +0.008
+3 +0.007
+2 +0.006
+1 +0.005
0 +0.004
−1 +0.003
−2 +0.002
−3 +0.001
−4
PINION DEPTH MEASUREMENT AND ADJUSTMENT
Measurements are taken with pinion cups and pin-
ion bearings installed in housing. Take measure-
ments with a Pinion Gauge Set, Pinion Block 6735,
Arbor Discs 6732, and Dial Indicator C-3339 (Fig.
66).
(1) Assemble Pinion Height Block 6739, Pinion
Block 6735, and rear pinion bearing onto Screw 6741
(Fig. 66).
(2) Insert assembled height gauge components,
rear bearing and screw into axle housing through
pinion bearing cups (Fig. 67).
(3) Install front pinion bearing and Cone 6740
hand tight (Fig. 66).
pinion depth variance
PINION GEAR DEPTH VARIANCE
Replacement Pinion Gear Depth Variance
−4 −3 −2
+0.007 +0.006
+0.006 +0.005
+0.005 +0.004
+0.004 +0.003
+0.003 +0.002
+0.002 +0.001
+0.001 0
0 −0.001
0 −0.001 −0.002
is
Fig. 65 Shim Locations
1 – PINION GEAR DEPTH SHIM
2 – DIFFERENTIAL BEARING SHIM-PINION GEAR SIDE
3 – RING GEAR
4 – DIFFERENTIAL BEARING SHIM-RING GEAR SIDE
5 – COLLAPSIBLE SPACER
−1 0
+0.005 +0.004 +0.003
+0.004 +0.003 +0.002
+0.003 +0.002 +0.001
+0.002 +0.001
+0.001 0 −0.001
0 −0.001 −0.002
−0.001 −0.002 −0.003
−0.002 −0.003 −0.004
−0.003 −0.004 −0.005
(4) Place Arbor Disc 6732 on Arbor D-115-3 in posi-
tion in axle housing side bearing cradles (Fig. 68).
Install differential bearing caps on Arbor Discs and
tighten cap bolts. Refer to the Torque Specifications
in this section.
NOTE: Arbor Discs 6732 have different step diame-
ters to fit other axle sizes. Pick correct size step for
axle being serviced.
(5) Assemble Dial Indicator C-3339 into Scooter
Block D-115-2 and secure set screw.
+1 +2 +3
+0.002 +0.001
+0.001 0
0 −0.001
0 −0.001 −0.002
−0.002 −0.003
−0.003 −0.004
−0.004 −0.005
−0.005 −0.006
−0.006 −0.007
XJ
+4
0
−0.001
−0.002
−0.003
−0.004
−0.005
−0.006
−0.007
−0.008