Table of Contents
Advertisement
Start Auto Image Menu
INPUT 1
COMPOSITE
Input Configuration Menu
START AUTO
IMAGE ON IN1
MENU
INPUT
INPUT 2
NEXT
CONFIG
NOTE: Input 1 can only
accept composite video.
Input 3 can only accept
S-video. Only Inputs 2 and
4 can be configured for
Select video format
different video types,
• Composite
although an SDI input can
• S-video
be assigned to any input.
• YUVi
• YUVp/HDTV
• YUV Auto
DVS 304 DVI models only
Displays only on Input 4
VGA EDID
NEXT
NEXT
1024x768@60
EDID Emulation
Specify the resolution
and refresh rate.
NOTE: See table in the "Resolutions
and Refresh Rates" section, for EDID values.
Picture Control
INPUT
CONFIG
MENU
PICTURE
NEXT
CONTROL
Default Cycle
2 sec.
OUTPUT
2 sec.
1024 x 768@60
INPUT 4
NEXT
NEXT
YUVi
RGB SCALED
Select video format
• Composite
• S-video
• RGBcvS
• YUVi
• YUVp/HDTV
• RGB scaled
• RGB pass*
• Auto detect
NOTE: * RGB pass through is only
available on analog outputs.
Displays only when applicable
FILM MODE
H ACTIVE V
NEXT
<OFF> ON
XXX
XXX
Film mode
Horizontal active
Vertical active
Turn On or Off for low
pixels
lines
resolution devices.
Specify the width
Specify the
in pixels of the
height in lines of
NOTE: Not for use with
active image area
the active image
YUVp or RGB inputs.
sampled.
area sampled.
H
POS V
H
SIZE V
NEXT
000
000
1024
768
Horizontal
Vertical
Horizontal
position
position
sizing
Adjust
Adjust
Adjust
horizontal
vertical
horizontal
image
image
image
position.
position.
sizing.
Only applicable when zoom is over 100 %
H
PAN
V
NEXT
000
000
Pan
Move the "zoomed"
image horizontally or
vertically. Available only
when zoom is set over
100%.
START AUTO
MENU
NEXT
IMAGE ON IN1
PRESS NEXT
NEXT
TO START
Displays only when applicable
Displays only when applicable
SDI INPUT
SDI DE-INTER
NEXT
< * > 1 2 3 4
FIELD STNDRD
SDI De-interlacing options:
• Field Standard
• Field Flip
Assign SDI to Input #
• 1, 2, 3, 4, * (none)
NOTE: The SDI input signal
can be assigned to any
input. Once assigned to a
specific input, only an SDI
signal can be accepted on
that input. SDI can be
disabled by selecting the *.
H
START V
NEXT
NEXT
50
33
Horizontal start
Vertical start
Select for the
Select for the
left edge of the
top edge of the
active video.
active video.
BRIGHT CONT
NEXT
NEXT
064
064
Contrast
Brightness
Vertical
Adjust image
Adjust image
sizing
contrast.
brightness.
Adjust
vertical
image
sizing.
ZOOM
NEXT
NEXT
100%
Zoom
Allows for 100-200% zoom
while the aspect ratio
remains unchanged.
DVS 304 Series • Menu System
ASPECT RATIO
NEXT
4x3
Aspect ratio options
• 4 x 3
• 16 x 9
Displays only when applicable
TTLPIX PHASE
NEXT
XXXX
08
For YUVp or RGB input only
Total pixels
Pixel phase
Specify the width
Adjust the pixel
in pixels of the
sampling point for
total image area
a selected input.
sampled.
Tint adjustment applicable only for
NTSC composite or S-Video inputs
COLOR
TINT
NEXT
064
064
Tint
Color
Adjust tint
Adjust color
of image.
of image.
DETAIL
064
Detail
Adjust sharpness of
the image.
75
Advertisement
Table of Contents
