Extron electronics DVS 304 Series Setup Manual

DVS 304 Series – Setup Guide
The Extron DVS 304 Series of video and RGB digital scalers incorporate advanced technology
to provide high performance video processing with selectable output rates up to 1920x1200
(DVI models only) and HDTV 1080p, as well as simultaneous DVI (DVI models only) and
analog RGB or component video outputs.
This setup guide allows quick and easy set up and configuration of a DVS scaler using step by step instructions. It covers
performing basic operations using the front panel controls and selected Simple Instruction Set (SIS
N For full installation, configuration, and operation details, refer to the DVS 304 Series User's Manual, online at www.extron.com.
Installation — Rear Panel Features (DVS 304 DVI AD model shown)
DVS 304 DVI AD
100-240V .3A
AUDIO
INPUTS
L 1 R L 2 R L 3 R L 4
50/60 Hz
2
1
Power and video input connections
a
AC power connector
b
Audio input captive screw connectors (inputs 1 to 4) - audio models only
c
Composite video BNC connector (input 1)
Ñ
(Optional) SDI BNC connectors (configurable)
d
Composite video/S-video/component video BNC connectors (input 2)
e
S-video 4-pin mini-DIN connector (input 3)
f
15-pin HD connector (input 4) with EDID emulation*

Installation and cabling

Step 1 — Mount the DVS
Turn off or disconnect all equipment power sources and rack mount the DVS unit, using
suitable mounting brackets or rack shelf (see image at right).
Refer to the DVS 304 Series User's Manual for details.
Step 2 — Connect inputs
Connect inputs from video and/or audio sources to the applicable connectors marked
b f
"Inputs" (see to above for connector types). See diagrams below for signal format on BNC
connectors and audio input captive screw wiring (balanced or unbalanced, mono or stereo).
N
When connecting a VGA input to a DV 304 DVI model, by default the EDID emulation is set to match the current output rate. To set to a specific rate,
or set to a display's EDID rate, or to upload a custom EDID table refer to the DVS 304 Series User's Manual, available at www.extron.com.
Input 2
Component video
(Y, R-Y, B-Y)
Y B-Y
/VID /C
R-Y
Input 4
Pin 1
15-HD pins
R
Input source
BNC's
RGB R
R
RGBcvS
R-Y
YUV
S-video
Composite video
3a
SDI
I
N
P
U
OUTPUT
R
L R
T
VID
1
2
3
7
S-video Composite video
Y
Y
B-Y
/VID
/VID
/C
R-Y R-Y
Pin 13 Pin 14
Pin 3
Pin 2
G
B H V
H V
G(S)
B
G cvS
B
Y B-Y
C
Y
Y
6
Y B-Y
RGB/R-Y,Y,B-Y/YC/VID
R
/VID /C
/R-Y
4
H/
R-Y YC
HV
DVI-I
3
5
4 8
Output and control connections
g
Audio output connectors - (audio models only)
h
RGB/YUV-HD BNC and DVI* output connectors
i
Reset button and LED
j
RJ-45 Ethernet connector
k
9-pin D RS-232 connector
N
* DVI models only. Non DVI models have a 15-pin HD connector
in place of the DVI connector and do not feature EDID emulation.
B-Y
/C
Tip
Ring
Sleeve
Tip
Ring
Balanced Stereo Input
Tip
Ring
Sleeve
Tip
Ring
Balanced Mono Input
™ ) commands.
G B
O
/Y /B-Y
U
T
LAN
P
RS-232
RESET
U
T
V
ACT LINK
11
9 10
Do not tin the wires!
Tip
Sleeve
Tip
Sleeve
Unbalanced Stereo Input
Tip
Sleeve
Tip
Sleeve
Unbalanced Mono Input
Rack Mount
Bracket
68-1039-50
Rev. A
08 09