Operation - ADJ Vizi Q Wash7 User Instructions

Vizi Q Wash7
Stand-Alone (Auto Program):
run through a built-in program.
AUTO PROGRAM:
1. Access the main menu, and press the UP or DOWN buttons so
that "Function" is highlighted, then press ENTER.
2. Press the UP or DOWN buttons until "Disp. Set" is displayed,
and press ENTER.
3. Press the UP or DOWN buttons until "Auto. Pro" is displayed,
and press ENTER.
4. Either "Master" or "Alone" will be displayed. Using the UP or
DOWN buttons select "Alone" and press ENTER.
Master-Slave Cofiguration (Auto Program):
allow you to link up to 16 units together and operate without a control-
ler. In a Master-Slave set up, one unit will act as the controlling unit and
the others will react to the controlling units programs. Any unit can act
as a Master or as a Slave.
1. Using standard XLR cables, daisy chain your units together viathe
XLR connector on the rear of the units. Remember the Male XLR
connector is the input and the Female XLR connector is the
output. The first unit in the chain (master) will use the female XLR
connector only - The last unit in the chain will use the male XLR
connector only. For longer cable runs we suggest a terminator at
the last fixture.
2. On your "Master" unit, access the main menu, and press the UP
or DOWN buttons so that "Function" is highlighted, then
press ENTER.
3. Press the UP or DOWN buttons until "Disp. Set" is displayed,
and press ENTER.
4. Use the UP or DOWN buttons to highlight "Auto. Pro" and press
ENTER.
5. Either "Master" or "Alone" will be displayed. Using the UP or
DOWN buttons select "Master" and press ENTER.
6. For your "Slave" units, access the main menu, and press the UP
or DOWN buttons so that "Function" is highlighted, then
press ENTER.
7. Press the UP or DOWN buttons until "Disp. Set" is displayed,
and press ENTER.
ADJ Products, LLC - www.adj.com - Vizi Q Wash7 Instruction Manual Page 40

Operation

This mode allows a single unit to
This function will
Vizi Q Wash7
8. Press the UP or DOWN buttons until "Slave Set" is displayed,
and press ENTER.
9. Either Slave 1, Slave 2, or Slave 3 will be displayed. Select your
desired Slave setting and press ENTER.
10. Press MODE if you want to return to the main menu.
11. You may invert the pan and tilt functions in the system menu by
following the directions on pages 26-27.
Vizi Q Wash7
With this feature you are able to control the unit with DMX without the need
of XLR cables. Your DMX controller must be connected to a ADJ WiFly
TransCeiver to use this function. You are able to communicate up to 2500
feet/760 meters (open line of sight).
1. Follow the instructions on page 33 to activate WiFly and set the
Wireless address. The address must match the address set on the WiFly
Transceiver.
2. After you have set the WiFly address, follow the DMX instructions on
page 24 to select your desired DMX Channel mode and set your DMX
address.
3. Apply power to the ADJ WiFly Transceiver. The fixture must be set up
first before you apply power to WiFly Transceiver.
note: If the sync does not work, switch the WiFly power off then on again.
Vizi Q Wash7
This feature will let you link units to run in a master-slave mode without the
use of XLR cables.
1. Follow the instructions on page 33 to activate WiFly and set the
Wireless address. The address must match the address set on the WiFly
Transceiver.
2. After you have set the WiFly address, select your master unit and set
your desired operating mode.
3. For the Slave units, put the unit in Slave mode. See page 40 Master-
Slave configuration when setting the unit as a Slave.
nOTE: If they do not sync up master-slave, switch the Master fixtures
WiFly off then on again.
ADJ Products, LLC - www.adj.com - Vizi Q Wash7 Instruction Manual Page 41
Operation
WiFly Set Up
WiFly Master-Slave Set Up