Dell S4820T Configuration Manual page 431

NOTE: The CLI output may be incorrectly displayed as 0 (zero) for the Rx/Tx power values. To
obtain the correct power information, perform a simple network management protocol (SNMP)
query.
Examples of the show Commands
The following example shows the configuration and status information for one interface.
Dell#show interfaces tengigabitethernet 1/1
TenGigabitEthernet 1/1 is up, line protocol is up
Hardware is Force10Eth, address is 00:01:e8:05:f3:6a
Current address is 00:01:e8:05:f3:6a
Pluggable media present, XFP type is 10GBASE-LR.
Medium is MultiRate, Wavelength is 1310nm
XFP receive power reading is -3.7685
Interface index is 67436603
Internet address is 65.113.24.238/28
MTU 1554 bytes, IP MTU 1500 bytes
LineSpeed 10000 Mbit, Mode full duplex, Master
ARP type: ARPA, ARP Timeout 04:00:00
Last clearing of "show interface" counters 00:09:54
Queueing strategy: fifo
Input Statistics:
0 packets, 0 bytes
0 Vlans
0 64-byte pkts, 0 over 64-byte pkts, 0 over 127-byte pkts
0 over 255-byte pkts, 0 over 511-byte pkts, 0 over 1023-byte pkts
0 Multicasts, 0 Broadcasts
0 runts, 0 giants, 0 throttles
0 CRC, 0 overrun, 0 discarded
Output Statistics:
3 packets, 192 bytes, 0 underruns
3 64-byte pkts, 0 over 64-byte pkts, 0 over 127-byte pkts
0 over 255-byte pkts, 0 over 511-byte pkts, 0 over 1023-byte pkts
0 Multicasts, 3 Broadcasts, 0 Unicasts
0 Vlans, 0 throttles, 0 discarded, 0 collisions
Rate info (interval 299 seconds):
Input 00.00 Mbits/sec, 0 packets/sec, 0.00% of line-rate
Output 00.00 Mbits/sec, 0 packets/sec, 0.00% of line-rate
Time since last interface status change: 00:00:31
Dell#
To view which interfaces are enabled for Layer 3 data transmission, use the show ip interfaces
brief command in EXEC Privilege mode. In the following example, TenGigabitEthernet interface 1/6 is in
Layer 3 mode because an IP address has been assigned to it and the interface's status is operationally up.
Dell#show ip interface brief
Interface
TenGigabitEthernet 1/1
TenGigabitEthernet 1/2
TenGigabitEthernet 1/3
TenGigabitEthernet 1/4
TenGigabitEthernet 1/5
TenGigabitEthernet 1/6
TenGigabitEthernet 1/7
TenGigabitEthernet 1/8
TenGigabitEthernet 1/9
To view only configured interfaces, use the show interfaces configured command in the EXEC
Privilege mode. In the previous example, TenGigabitEthernet interface 1/6 is in Layer 3 mode because an
IP address has been assigned to it and the interface's status is operationally up.
Interfaces
IP-Address OK? Method
unassigned NO Manual
unassigned NO Manual
unassigned YES Manual
unassigned YES Manual
unassigned YES Manual
10.10.10.1 YES Manual
unassigned NO Manual
unassigned NO Manual
unassigned NO Manual
Status
administratively down
administratively down
up
up
up
up
administratively down
administratively down
administratively down
Protocol
down
down
up
up
up
up
down
down
down
431