Recording; Recording The Input Source; Recording From Different Av Sources - Onkyo TX-NR905 Instruction Manual

Recording

This section explains how to record the input source and
how to record audio and video from separate sources.
Notes:
• The surround sound and DSP listening modes cannot
be recorded.
• Copy-protected DVDs cannot be recorded.
• Sources connected to the analog multichannel input
cannot be recorded.
• Various restrictions apply to digital recording. Refer to
the manuals supplied with your digital recording
equipment for more details.
• Digital input signals are output by only the digital out-
puts, and analog input signals are output by only the
analog outputs. There is no internal conversion from
digital to analog or vice versa.
• DTS signals will be recorded as noise, so don't
attempt analog recording of DTS CDs or LDs.
• While the Pure Audio listening mode is selected, the
VCR/DVR OUT V and S jacks don't output video sig-
nals, so select another mode when recording.

Recording the Input Source

Audio sources can be recorded to a recorder (e.g., cas-
sette deck, CDR, MD) connected to the TAPE OUT or
DIGITAL OPTICAL OUT jacks. Video sources can be
recorded to a video recorder (e.g., VCR, DVR) con-
nected to the VCR/DVR OUT jacks. See pages 33 to 49
for hookup information.
1
Use the input selector buttons to
select the source that you want
to record.
VCR/DVR CBL/SAT
DVD
See "Which Connections Should I
Use?" on page 34 to see which signals
GAME/TV AUX 1 AUX 2
can be output and recorded.
TAPE
TUNER CD
You can watch the source while record-
PHONO NET/USB
ing it. The AV receiver's MASTER
Remote
VOLUME control has no effect on
controller
recording.
DVD VCR/DVR CBL/SAT
1 2 3
AUX 1 AUX 2
GAME/TV
4 5 6
TAPE TUNER CD
7 8 9
PHONO NET/USB
+10
0
2
On your recorder, start record-
ing.
3
On the source component, start
playback.
Note:
• If you select a different input source during recording,
that input source will be recorded instead.

Recording from Different AV Sources

You can overdub audio onto your video recordings by
simultaneously recording audio and video from two sep-
arate sources. This is possible because only the audio
source is switched when an audio-only input source,
such as TAPE, TUNER, or CD, is selected, the video
source remains the same.
In the following example, audio from the CD player con-
nected to the CD IN and video from the camcorder con-
nected to the AUX 2 INPUT VIDEO jack are recorded
by the VCR connected to the VCR/DVR OUT jacks.
PUSH TO OPEN
AUX 2 INPUT
VIDEO L AUDIO R
S VIDEO DIGITAL
video signal
audio signal
HDMI
ASSIGNABLE
RS232 IN 4 IN 3 IN 2
COMPONENT VIDEO
ASSIGNABLE
IN 3 IN 2 IN 1(DVD) MONITOR
OUT
Y
AUX 1
REMOTE C B /P B
V
CONTROL
DIGITAL ASSIGNABLE
COAXIAL
IN 1
(DVD) S
C R /P R
IN IN OUT IN IN
IN 2 (VCR/DVR)
L L
IN 3 (CBL/SAT)
R R
OPTICAL
PHONO
CD TAPE AUX 1
IN 1
(GAME/TV)
ZONE2 R
GND SURR BACK R
ASSIGNABLE
Bi-AMP
IN 2
(CD)
OUT
FRONT R (BTL)
CD player
1
Prepare the camcorder and CD player for
playback.
2
Prepare the VCR for recording.
3
Press the [AUX 2] input selector button.
4 Press the [CD] input selector button.
This selects the CD player as the audio source but
leaves the camcorder as the video source.
5 Start recording on the VCR, then start
playback on the camcorder and CD player.
Video from the camcorder and audio from the CD
player are recorded by the VCR.
Camcorder
IN 1 OUT OUT
MAIN SUB
ANTENNA
AM FM75
MONITOR
GAME/TV CBL/SAT VCR/DVR DVD OUT IR
V
IN
ZONE 2
OUT
S
OUT
IN IN OUT IN IN FRONT CENTER SURR SURR BACK
SUBWOOFER
GAME/TV CBL/SAT VCR/DVR DVD MULTI CH
FRONT R SURR R CENTER SURR L
VCR
87