Pyronix Enforcer 32WE Setup Manual page 19

Magnet
MC1-WE
Door
Contact
Contact
/ Sensor
Applying the battery
Door
Contact
/ Sensor
S1
Z T
T
C
Z
+
WINDOW
S1
Z T
Model:
T
Colour:
C
Casing:
Transmission Frequency:
Z
Transmission Method:
Learning the MC1-WE to the Enforcer control panel
Transmission Range:
+
Example:
Indication:
When you are ready to learn the device to the control panel receiving equipment, and when the
Model:
equipment is in the learn mode (see Enforcer Programming Manual) follow the procedure below.
Reed Switch:
Colour:
Detection Points:
Casing:
1. Make sure the battery is installed correctly and the plastic wrapping removed.
Detection Inputs:
Transmission Frequency:
2. Press and Hold the Learn button until the 3 LEDs start cycling through the different colours, then
Battery:
Transmission Method:
release the Learn button.
Battery Life:
Transmission Range:
3. The device is correctly learnt when the Green LED flashes.
Tamper Switch:
Indication:
Storage Temperature:
Reed Switch:
The three coloured LEDs give a visual indication of the signal strength.
Operating Temperature:
Detection Points:
Model:
Detection Inputs:
Colour:
Green indicates good signal strength and is a good location to install.
Battery:
Casing:
Battery Life:
Transmission Frequency:
Tamper Switch:
Red indicates poor signal strength and the device should not be
Transmission Method:
Storage Temperature:
installed in that position.
Transmission Range:
S1 Enable
Operating Temperature:
Indication:
T
If no LED illuminates then the device is completely out of range.
CR2 Battery
Reed Switch:
Detection Points:
Learn
Detection Inputs:
The blue LED will illuminate when the device is activated.
Battery:
Battery Life:
-
+
CR2 Battery
Tamper Switch:
Storage Temperature:
Example:
WINDOW
Wireless magnetic contact/universal transmitter
with 1 reed, 1 input & tamper
S1 S1 Enable
Example:
Z T
CR2 Battery
T
C
Z
S1 Enable
+
CR2 Battery
CR2 Battery
The batteries supplied have been chosen to provide long service life whilst, for safety
Learn
reasons, having limited output current.
The battery is protected on purchase by a piece of plastic that must be removed for
-
operation.
CR2 Battery
S1 Enable
To prevent possible damage to components, any static charge on your body needs
to be eliminated before touching the inside of the unit. This can be accomplished
MC1-WE
by touching some grounded/earthed metallic conductor such as a radiator/pipework
CR2 Battery
WHITE
immediately before replacing the batteries.
3mm ABS, 0.4mm HDPE in Lens Area
Learn
868MHz, FM Transceiver Narrow Band
Fully Encrypted Rolling Code
Universal Transmitter
300m Free Space
-
Z T
CR2 Battery
Three LED Combinations
(RSSI, Battery Status and Alarm)
MC1-WE
1 x MC1-WE
WHITE T
2, Side and End
3mm ABS, 0.4mm HDPE in Lens Area
C
1 External Input & 1 External Tamper Input
868MHz, FM Transceiver Narrow Band
3.6V 2.2Ahr AA Lithium Battery
Z
Fully Encrypted Rolling Code
Up to 2 Years
300m Free Space
Front + Optional Rear Tamper
Three LED Combinations
(RSSI, Battery Status and Alarm)
-20°C to 50°C
1 x MC1-WE
-10°C to 50°C
2, Side and End
MC1-WE
1 External Input & 1 External Tamper Input
WHITE
3.6V 2.2Ahr AA Lithium Battery
3mm ABS, 0.4mm HDPE in Lens Area
Up to 2 Years
868MHz, FM Transceiver Narrow Band
Front + Optional Rear Tamper
Fully Encrypted Rolling Code
-20°C to 50°C
Test Result
300m Free Space
-10°C to 50°C
Three LED Combinations
(RSSI, Battery Status and Alarm)
1 x MC1-WE
2, Side and End
1 External Input & 1 External Tamper Input
3.6V 2.2Ahr AA Lithium Battery
If the battery needs to be replaced, the
Up to 2 Years
correct battery type (CR2) must be
Front + Optional Rear Tamper installed
-20°C to 50°C
Universal Transmitter
Z T
T
C
Z
Test Result
Universal Transmitter
Z T
Using Magnetic Contact 1 (S1)
T
Door Frame
C
Learn
Door
Z
Test Result
If the battery needs to be replaced, the
-
correct battery type (CR2) must be
installed
If the battery needs to be replaced, the
correct battery type (CR2) must be
installed
Test Result
TAMPER
If the battery needs to be replaced, the
correct battery type (CR2) must be
installed
19
ZONE
TAMPER
ZONE
To enable Magnetic Contact 1 you must remove
jumper link from the S1 enable pins:
Reed Switch
S1 S1 Enable
Z T
T
C
Z
Magnetic
Contact 1
Tamper
Zone
Enable/
Enable/
Enable/
Disable
Disable
Disable
S1 S1 Enable
Z T
T
C
ZONE
Z
RED
RED
RED
RED
RED
Magnetic
C
Contact 1
Tamper
Zone
Learn
Z
Enable/
Enable/
Enable/
Disable
Disable
Disable
S1
S1 Enable
Z T
T
C
Learn
Z
RED BLUE G
RED BLUE G
Test Result
RED BLUE G
Learn
S2 Enable
RED BLUE G
RED BLUE G
RED
RED BLUE G
Status LEDs
RED BLUE G
Test Result
RED BLUE G
RED
Learn
Learn
Button
BLUE GREEN
BLUE GREEN
BLUE GREEN
BLUE GREEN
BLUE GREEN
Learn
Butto
Learn
Butto
BLUE G
BLUE G