Page 1
DDW2600 Wireless Router (U10CC037) DDC2700 Commercial Router (U10C038) Subscriber User Guide DDW2600 Wireless Cable Modem/Router DDC2700 Commercial Cable Modem/Router www.ubeeinteractive.com 8085 S. Chester Street, Suite 200 Englewood, CO 80112 1.888.390.8233 Release Version Sales (email): amsales@ubeeinteractive.com 5/20/10 Support (email) amsupport@ubeeinteractive.com...
Page 2
This material is protected by the copyright laws of the United States and other countries. It may not be reproduced, distributed, or altered in any fashion by any entity (either internal or external to Ubee), except in accordance with applicable agreements, contracts, or licensing, without the express written consent of Ubee and the business management owner of the material.
Do not expose this device to direct sunlight. Do not place any hot devices close to this device, as it may degrade or cause damage to it. DDW2600 Wireless & DDC2700 Commercial Cable Modem/Router Subscriber User Guide • May, 2010...
2 dBi. Antenna having a higher gain is strictly prohibited per regulations of Industry North America. The required antenna impedance is 50 ohms. DDW2600 Wireless & DDC2700 Commercial Cable Modem/Router Subscriber User Guide • May, 2010...
Ethernet Enabled Devices, Cable Modem/Router PCs, Gaming Consoles, etc. Support Subscribers must contact their service provider for direct support. Device documentation support may be available at: http://www.ubeeinteractive.com DDW2600 Wireless & DDC2700 Commercial Cable Modem/Router Subscriber User Guide • May, 2010...
26 digit HEX value. This value is equal to the device MAC address plus 14 zero’s (all lower case without the colons). Example: 00028A1A345600000000000000 (MAC address + 14 Zero’s) Broadcast Channel: The default broadcast channel is 1. DDW2600 Wireless & DDC2700 Commercial Cable Modem/Router Subscriber User Guide • May, 2010...
Vin = 230V 50Hz Vout = 12V; 1.5A Example: Actual appearance subject to change. USB Cable and Driver CD (not shown). Drivers are also available at: www.ubeeinteractive.com DDW2600 Wireless & DDC2700 Commercial Cable Modem/Router Subscriber User Guide • May, 2010...
5 - Cable Port The Cable port is where the device connects to the cable wall outlet, or a cable splitter connected to the wall outlet. DDW2600 Wireless & DDC2700 Commercial Cable Modem/Router Subscriber User Guide • May, 2010...
DDW2600 wireless cable modem/router or the DDM2700 commercial cable modem/router. Review the device images below and the LED table on the following page. 2.7.1 DDW2600 and DDC2700 Front Panel Images DDW2600 DDC2700 DDW2600 Wireless & DDC2700 Commercial Cable Modem/Router Subscriber User Guide • May, 2010...
Traffic Traffic Upgrade In On, if Slow Flash On, Slow On, if On, if On, if On, if Progress Connected Flash if Connected Connected Connected Connected Traffic DDW2600 Wireless & DDC2700 Commercial Cable Modem/Router Subscriber User Guide • May, 2010...
Page 16
2.7.2 LED Behavior Table Ubee Interactive DDW2600 Wireless & DDC2700 Commercial Cable Modem/Router Subscriber User Guide • May, 2010...
2. In the internet browser, enter the following address and press <Enter/Return>: http://192.168.0.1 3. The Cable Modem Information window is displayed. Click the Login link on the left side of the window. DDW2600 Wireless & DDC2700 Commercial Cable Modem/Router Subscriber User Guide • May, 2010...
Page 19
Username: user Password: user 5. Accessing the web interface is an initial way to validate the installation. No extra steps are required at this point for a basic LAN and/or wireless network (DDW2600 only). 6. Proceed to page 16 to test network connectivity and/or to add both Ethernet LAN devices and wireless devices (DDW2600 only) to the network.
Refer to LED Behavior Table, on page 11 for more detailed information. 2. Connect a wireless device to the DDW2600 (for example, a laptop computer). Use the following steps: Access the wireless networking feature on your wireless device. On a Windows computer, for example, double-click the Wireless Networking icon in the system tray (lower-right side of the Windows desktop).
The Ethernet cable may be damaged. Try another cable. If none of these suggestions work, contact your cable service provider for further assistance. DDW2600 Wireless & DDC2700 Commercial Cable Modem/Router Subscriber User Guide • May, 2010...
Page 22
3.2.2 Additional Troubleshooting Information Ubee Interactive DDW2600 Wireless & DDC2700 Commercial Cable Modem/Router Subscriber User Guide • May, 2010...
The current DOCSIS standard of the device. MAC Address The unique Media Access Control (MAC) hardware address of cable modem. Serial Number The unique manufacturer serial number of the device. DDW2600 Wireless & DDC2700 Commercial Cable Modem/Router Subscriber User Guide • May, 2010...
(Online/Offline). The Comments column displays the reason why cable modem’s connectivity state is not Online. Boot State Shows the registration status of the device. Security If BPI is enabled, the status will displays Enabled. DDW2600 Wireless & DDC2700 Commercial Cable Modem/Router Subscriber User Guide • May, 2010...
Displays the receiver power level after ranging process. Downstream SNR Display the SNR of this downstream channel. Refresh Click this button to refresh the active screen data. DDW2600 Wireless & DDC2700 Commercial Cable Modem/Router Subscriber User Guide • May, 2010...
(dBmV). Upstream Mini-Slot Size Displays the current cable modem upstream mini-slot size in Timebase Ticks of 6.25. Refresh Click this button to refresh the active screen data. DDW2600 Wireless & DDC2700 Commercial Cable Modem/Router Subscriber User Guide • May, 2010...
Scrambler Seed 15 bits (Not used if scrambler is off) Maximum Burst Size 0-255 (mini-slots) Guard Time Size 4-255 (symbols) Last Codeword Length Fixed/shortened Scrambler on/off On/Off DDW2600 Wireless & DDC2700 Commercial Cable Modem/Router Subscriber User Guide • May, 2010...
1. Access the web interface. Refer to page 14, if needed. 2. Click the Event Log link from the left side of the screen. Field explanations are DDW2600 Wireless & DDC2700 Commercial Cable Modem/Router Subscriber User Guide • May, 2010...
Page 29
Displays the event log severity. Description Displays a detailed description of the event log. Refresh/Clear Log Refreshes the event log record. Click Clear Log to clear the screen. DDW2600 Wireless & DDC2700 Commercial Cable Modem/Router Subscriber User Guide • May, 2010...
Displays the subnet mask of the Internet IP address. Default Gateway Displays the default gateway IP address. Displays the DNS server IP address. DHCP Remaining Displays the remaining DHCP lease time Time before expiration DDW2600 Wireless & DDC2700 Commercial Cable Modem/Router Subscriber User Guide • May, 2010...
Page 31
Displays the Public IP DHCP Server Range. Server Range Public IP Total Displays the Public IP total range. Range System Up-Time Displays the accumulated time since the last power cycle. DDW2600 Wireless & DDC2700 Commercial Cable Modem/Router Subscriber User Guide • May, 2010...
Click to release the WAN public IP address. Renew WAN Lease Click to renew the WAN IP address. Refresh Click to refresh the status of this page. DDW2600 Wireless & DDC2700 Commercial Cable Modem/Router Subscriber User Guide • May, 2010...
Page 33
(256-1500). If this is not given by the Service Provider, leave it as is using 0 for the default. Apply Click to save all changes made in the screen. DDW2600 Wireless & DDC2700 Commercial Cable Modem/Router Subscriber User Guide • May, 2010...
Define the maximum number of Customer Premises equipment (CPE) that can connect to the network, via the cable modem. This number determines the end of the public IP address range started above. DDW2600 Wireless & DDC2700 Commercial Cable Modem/Router Subscriber User Guide • May, 2010...
Page 35
Click Force Available to activate a selected rule in the DHCP Clients List, and assign the displayed private IP address statically to the connected network client. Note: The Select checkbox must be clicked. DDW2600 Wireless & DDC2700 Commercial Cable Modem/Router Subscriber User Guide • May, 2010...
Enter a specific IP address to assign to the specific client/host. Enabled Click Enabled to activate this rule. Clear Click Clear to delete the rule. Apply Click Apply to save all screen changes. DDW2600 Wireless & DDC2700 Commercial Cable Modem/Router Subscriber User Guide • May, 2010...
These fields are automatically populated once the User Name and Password are entered. Apply Click Apply to save all screen changes. Refresh Click to refresh the page. DDW2600 Wireless & DDC2700 Commercial Cable Modem/Router Subscriber User Guide • May, 2010...
Time Server 3 Defines the Time server IP address or Domain name. Use the one provided, or enter an alternative choice. DDW2600 Wireless & DDC2700 Commercial Cable Modem/Router Subscriber User Guide • May, 2010...
Page 39
For example: 8 means GMT + 08, -1 means GMT -01. Apply Click Apply to save all screen changes. Reset Values Click Reset Values to reset the screen to factory defaults. DDW2600 Wireless & DDC2700 Commercial Cable Modem/Router Subscriber User Guide • May, 2010...
Page 40
4.2.6 Gateway - Time Ubee Interactive DDW2600 Wireless & DDC2700 Commercial Cable Modem/Router Subscriber User Guide • May, 2010...
In turn, a device can leave a network smoothly and automatically when it is no longer in use. Apply Click Apply to save all screen changes. DDW2600 Wireless & DDC2700 Commercial Cable Modem/Router Subscriber User Guide • May, 2010...
LAN. Any host listed on this list will not be accessible to internet traffic. 1. Access the web interface. Refer to page 14, if needed. 2. Click the Gateway link from the top of the screen. DDW2600 Wireless & DDC2700 Commercial Cable Modem/Router Subscriber User Guide • May, 2010...
2. Click the Gateway link from the top of the screen. 3. Click Port Filtering from the left side of the screen. The Port Filtering fields are DDW2600 Wireless & DDC2700 Commercial Cable Modem/Router Subscriber User Guide • May, 2010...
Page 44
Select the protocol type, or select Both for UDP and TCP. Enabled Select Enabled to activate the rule and filter out all traffic on the specified ports. Apply Click Apply to save all screen changes. DDW2600 Wireless & DDC2700 Commercial Cable Modem/Router Subscriber User Guide • May, 2010...
For detailed information on port forwarding, including how to set it up for specific applications using specific network devices (for example, cable modems), refer to: http://portforward.com DDW2600 Wireless & DDC2700 Commercial Cable Modem/Router Subscriber User Guide • May, 2010...
Select the protocol type, UDP, TCPIP, or Both. Enabled Select to enable this rule. Apply Click to save. Port Map Click to show a list of common applications and their ports. DDW2600 Wireless & DDC2700 Commercial Cable Modem/Router Subscriber User Guide • May, 2010...
IP address:port number. Port Forwarding rules are created per port. So a rule set up for port 53 will only work for port 53. A port can only be used by one program at a time. DDW2600 Wireless & DDC2700 Commercial Cable Modem/Router Subscriber User Guide • May, 2010...
(or range of ports) to the client computer on the LAN that requested the service Start Port Enter a port number or the starting port number in a range of port numbers. DDW2600 Wireless & DDC2700 Commercial Cable Modem/Router Subscriber User Guide • May, 2010...
Page 49
Enter a port number or the ending port number in a range of port numbers. Protocol Define the protocol type for this rule, UDP, TCP, or Both. Enable Click to activate this rule. Apply Click to save. DDW2600 Wireless & DDC2700 Commercial Cable Modem/Router Subscriber User Guide • May, 2010...
3. The cable modem forwards the traffic to John’s computer IP address. 4. Only John can connect to the Real Audio server until the connection is closed or times out. DDW2600 Wireless & DDC2700 Commercial Cable Modem/Router Subscriber User Guide • May, 2010...
Index Index number of the pass through rule. MAC Address Input the host’s MAC address. Clear Select the box to delete this rule. Apply Click to save. DDW2600 Wireless & DDC2700 Commercial Cable Modem/Router Subscriber User Guide • May, 2010...
3. Click DMZ Host from the left side of the screen. The DMZ Host fields are explained following this screen example. Label Description DMZ Address Enter the DMZ host IP address. Apply Click to save. DDW2600 Wireless & DDC2700 Commercial Cable Modem/Router Subscriber User Guide • May, 2010...
Broadcast SSID Click Enable to allow broadcast of SSID. Country When set to USA, channels 1 to 11 is available. If selecting worldwide, 13 channels are available. DDW2600 Wireless & DDC2700 Commercial Cable Modem/Router Subscriber User Guide • May, 2010...
Page 54
Off makes the wireless access point unavailable for use. Apply Click to save. Restore Wireless Click to restore the factory default settings for wireless Defaults configurations. DDW2600 Wireless & DDC2700 Commercial Cable Modem/Router Subscriber User Guide • May, 2010...
Wi-Fi Protected Access (WPA) is a subset of the IEEE 802.11i standard. Key differences between WPA and WEP are user authentication and improved data encryption. Select to Enable or Disable. DDW2600 Wireless & DDC2700 Commercial Cable Modem/Router Subscriber User Guide • May, 2010...
Page 56
Both the wireless stations and the wireless router must use the same WEP key. Data Encryption can be set to WEP 128-bit, 64-bit, or Disable. DDW2600 Wireless & DDC2700 Commercial Cable Modem/Router Subscriber User Guide • May, 2010...
Page 57
When a WPS supported device tries to connect to this wireless router, the user has to input the PIN as specified in this STA PIN field. Apply Click to save all values/changes for WPS. DDW2600 Wireless & DDC2700 Commercial Cable Modem/Router Subscriber User Guide • May, 2010...
Page 58
14) and click the Start WPS button on this screen to trigger the negotiation between the wireless client and the wireless router. WPS Status displays the connection status between the device and wireless clients. DDW2600 Wireless & DDC2700 Commercial Cable Modem/Router Subscriber User Guide • May, 2010...
Input the MAC addresses. You may consider cutting and pasting MAC addresses from the connected clients list at the bottom of the screen. Apply Click to save. DDW2600 Wireless & DDC2700 Commercial Cable Modem/Router Subscriber User Guide • May, 2010...
Page 60
Age(s)—The duration since the wireless client connected to wireless router. RSSI(dBm)—Received signal strength in the wireless environment. IP Addr—The IP address assigned to this wireless client. Host Name—The host name of the wireless client. DDW2600 Wireless & DDC2700 Commercial Cable Modem/Router Subscriber User Guide • May, 2010...
2. Click the Wireless link from the top of the screen. 3. Click Guest Network from the left side of the screen. The Guest Network fields are explained following this screen example. DDW2600 Wireless & DDC2700 Commercial Cable Modem/Router Subscriber User Guide • May, 2010...
Page 62
RADIUS Key Allows the wireless router to generate the best possible random group key and update all the key-management Group Key Rotation Interval capable stations periodically. DDW2600 Wireless & DDC2700 Commercial Cable Modem/Router Subscriber User Guide • May, 2010...
Define the subnet mask value. Lease Pool Start Define the start IP address of this DHCP address pool. Lease Pool End Define the last IP address of this DHCP address pool. DDW2600 Wireless & DDC2700 Commercial Cable Modem/Router Subscriber User Guide • May, 2010...
Page 64
DHCP client will resend DHCP request. Max value is Lease Time 86400 seconds. Apply Click Apply to save all DHCP settings. Click to reset to factory default values for the wireless Restore Defaults settings only. DDW2600 Wireless & DDC2700 Commercial Cable Modem/Router Subscriber User Guide • May, 2010...
3. Click Enable from the left side of the screen. 4. Select the button to either Enable or Disable VPN. The device must be rebooted for the change to take effect. DDW2600 Wireless & DDC2700 Commercial Cable Modem/Router Subscriber User Guide • May, 2010...
Click Edit to modify IPSec VPN parameters of this tunnel; Click Delete to delete this IPSec VPN tunnel. Add New Tunnel Click to quickly create a new IPSec VPN tunnel, and then to modify its parameters. DDW2600 Wireless & DDC2700 Commercial Cable Modem/Router Subscriber User Guide • May, 2010...
Select the specific VPN tunnel to configure/edit, unless there are no tunnels in the system. Name Enter/edit the name for the tunnel. Delete Tunnel Click this button to delete the selected VPN tunnel. DDW2600 Wireless & DDC2700 Commercial Cable Modem/Router Subscriber User Guide • May, 2010...
Page 68
Select the identity type to identify this cable modem by: WAN IP (remote end point) address IP address FQDN Email address Identity Enter the value corresponding to the selected Identity Type. DDW2600 Wireless & DDC2700 Commercial Cable Modem/Router Subscriber User Guide • May, 2010...
Page 69
SA lifetime increases security by forcing the two VPN gateways to update the encryption and authentication keys. However, every time the VPN tunnel renegotiates the keys, all users accessing remote resources are temporarily disconnected. DDW2600 Wireless & DDC2700 Commercial Cable Modem/Router Subscriber User Guide • May, 2010...
Page 70
Denial of Service (DOS) attacks. The IPSec receiver can detect and reject old or duplicate packets to protect against replay attacks. DDW2600 Wireless & DDC2700 Commercial Cable Modem/Router Subscriber User Guide • May, 2010...
Click to save all changes. 4.4.4 VPN Configure - Advanced Settings The following screen is displayed when the Show Advanced Settings button is clicked from the VPN Configure screen (previous section). DDW2600 Wireless & DDC2700 Commercial Cable Modem/Router Subscriber User Guide • May, 2010...
VPN. Reenter the password in the Confirm Password field. User List All added users are displayed. L2TP Preshared Enter a Preshared Phrase. Phrase Apply Click to save the configuration. DDW2600 Wireless & DDC2700 Commercial Cable Modem/Router Subscriber User Guide • May, 2010...
An added feature of the ESP is payload padding, which further protects communications by concealing the size of the packet being transmitted. DDW2600 Wireless & DDC2700 Commercial Cable Modem/Router Subscriber User Guide • May, 2010...
Description Displays detailed information of a log. Refresh Click to refresh the current page to view new log events. Clear Click to clear all of the logs. DDW2600 Wireless & DDC2700 Commercial Cable Modem/Router Subscriber User Guide • May, 2010...
3. Click User Setup from the left side of the screen. The User Setup fields are explained following this screen example. Note: To enable Parental Control, refer to page DDW2600 Wireless & DDC2700 Commercial Cable Modem/Router Subscriber User Guide • May, 2010...
Page 76
Enter the trusted host’s MAC address and click the Add button to save. Remove To remove a trusted computer, highlight it from the list and click the Remove button. DDW2600 Wireless & DDC2700 Commercial Cable Modem/Router Subscriber User Guide • May, 2010...
Select from the list an existing policy to edit or remove. If List/Remove Policy removing a policy, select it from the list and click the Remove Policy button. DDW2600 Wireless & DDC2700 Commercial Cable Modem/Router Subscriber User Guide • May, 2010...
Add New Policy Enter a policy name and click the Add New Policy button. Time Access Policy List Select a policy to edit from the drop-down list. DDW2600 Wireless & DDC2700 Commercial Cable Modem/Router Subscriber User Guide • May, 2010...
Displays the source IP address of this event. Refresh/Clear Log Click Refresh to update the log with the most currently recorded events. Click Clear to empty the displayed log entries. DDW2600 Wireless & DDC2700 Commercial Cable Modem/Router Subscriber User Guide • May, 2010...
2. Click the Firewall link from the top of the screen. 3. Click Content Filter from the left side of the screen. The Content Filter fields are explained following this screen example. DDW2600 Wireless & DDC2700 Commercial Cable Modem/Router Subscriber User Guide • May, 2010...
Page 81
Enable this feature to have the firewall to protect all of the incoming connection routed subnets connected to the cable modem. requests on routed subnet Apply Click to save the configuration. DDW2600 Wireless & DDC2700 Commercial Cable Modem/Router Subscriber User Guide • May, 2010...
2. Click the Firewall link from the top of the screen. 3. Click Remote Log from the left side of the screen. The Remote Log fields are explained following this screen example. DDW2600 Wireless & DDC2700 Commercial Cable Modem/Router Subscriber User Guide • May, 2010...
Page 83
Commercial Cable Modem/Router is configured/modified by a user or admin. SysLog server Enter the IP address of the Syslog server. Apply Click to save the remote log configuration. DDW2600 Wireless & DDC2700 Commercial Cable Modem/Router Subscriber User Guide • May, 2010...
Ping Size Enter the packet size to send for the ping operation. No. of Pings Enter the number of ping commands to send to the ping target. DDW2600 Wireless & DDC2700 Commercial Cable Modem/Router Subscriber User Guide • May, 2010...
Enter the specific IP address or domain (e.g. yahoo.com) to which you want to trace a route. MAX Hops Define the MAX hops. Hops is the number routers that the trace route traverses. DDW2600 Wireless & DDC2700 Commercial Cable Modem/Router Subscriber User Guide • May, 2010...
Refresh Click to refresh the client list. This may be useful when testing network connectivity between connecting clients and the DDW2600 Wireless & DDC2700 Commercial Cable Modem/Router. DDW2600 Wireless & DDC2700 Commercial Cable Modem/Router Subscriber User Guide • May, 2010...
9300000, the cable modem will scan from 93000000 to 99000000, then from 99000000 to 105000000, and so on until the Highest Center Frequency is reached. DDW2600 Wireless & DDC2700 Commercial Cable Modem/Router Subscriber User Guide • May, 2010...
Password/Confirm field. Otherwise, leave as is. To change the password, enter Password the new password, and re-enter the new password in the Confirm password field. Click Apply. DDW2600 Wireless & DDC2700 Commercial Cable Modem/Router Subscriber User Guide • May, 2010...
Reset The system Select Yes to power cycle and reset the device. Apply Click Apply to complete the options selected in this screen. DDW2600 Wireless & DDC2700 Commercial Cable Modem/Router Subscriber User Guide • May, 2010...