List Of Functions - Ricoh L4160 Operation Manual

List of Functions

This section describes the overview of each function to be set and set values that can be registered in user
types.
• About default "HOST" function
You can operate this by the setting value specified in RIP software.
When you set to other than "HOST", it operates by that setting value, not by the instruction from RIP
software.
Depending on RIP software, there are some functions that cannot be instructed by software. In such a
case, it operates by the setting value of "When no instruction from RIP exists".
• For the specifying method with the RIP software, refer to the operation manual of the RIP software.
Function name
FEED COMP. ( P.2-23)
DROP. POS CORRECT
Pre-Heater
Print Heater
HEATER
( P.2-17)
Post Heater
FAN HEATER
18)
LOGICAL SEEK( P.3-3)
INK LAYERS ( P.3-9)
DRYING
TIME SCAN
( P.3-4)
LEFT
MARGIN
( P.3-5)
RIGHT
VACUUM ( P.3-9)
FEED SPEED ( P.3-9)
OFF / ON
MAPS
PRINT SPEED
( P.3-6)
ADJUST
INTERVAL
AUTO
CLEANING
TYPE
( P.3-7)
INTERVAL TYPE1
WIPING
TYPE2
( P.3-8)
*1. This is the setting value to be used for printing when setting value is not specified at the RIP software (host) side, or, you give priority
to the setting value at the machine side, even if you set "Host" to the type registration of this machine.
*2. The setting value range shall be within the POST heater setting value +20 ℃ .
*3. When you set this to "100%" or more, required time for completion of printing will be shortened. However, enough drying time cannot
be ensured and it may affect the image quality.
3-2
Set value
-9999 ~ 0 ~ 9999
-40.0 ~ 0 ~ 40.0
OFF/ 20 ~ 70°C
(OFF/ 68 ~ 122°F)
OFF/ 20 ~ 70°C
(OFF/ 68 ~ 122°F)
OFF/ 20 ~ 70°C
(OFF/ 68 ~ 122°F)
( P.2- OFF/
*2
POST+0 ~ 20°C
HOST / ON / OFF
HOST /1 ~ 9
HOST /0.0 ~ 9.9 sec
HOST / -10 ~ 85mm
(1mm unit)
HOST / -10 ~ 85mm
(1mm unit)
HOST / STANDARD /
STRONG
HOST / 10 ~ 200%
-50 ~ +50%
OFF / 1 ~ 1000 page
SOFT / NORMAL /
HARD
Lv1 ~ Lv6,
MANUAL(90~600sec)
Lv1 ~ Lv6,
MANUAL(10~90min)
When no instruction
Default
*1
from RIP exists
Used to print a pattern for
0 correcting a media-feeding rate
and correct it.
Used to adjust the dot position in
0
go and return printing.
OFF
OFF Sets heater conditions.
OFF
Sets drying heater conditions.
OFF
Sets the scan movable area
HOST OFF
during printing.
Sets the number of layers in
1
HOST
which ink is to be applied.
Sets the time to wait for ink
HOST 0.0 sec
drying.
0 mm
HOST
Sets a non-printing area along
the right and left edges of the
0 mm media.
HOST
Sets the absorbability of the
STANDARD
HOST
media.
Changes
HOST 100%
speed in printing.
OFF
Perform setting to reduce stripes
between passes.
0%
OFF
Sets
operation of the head at the start
SOFT
of printing.
Lv4
Set wiping interval performed
during printing.
Lv4
Outline
the media feeding
*3
the automatic cleaning