Xerox Phaser 8860 Service Manual page 90

Table 3 Jam Code Troubleshooting
Code Description / Procedure
T2A Exit Door Interlock tripped following an abnormal shutdown.
T2B Exit Door Interlock tripped following a normal shutdown.
T2C Exit Door Interlock tripped during mechanical recovery
T2D Exit Door Interlock tripped during warm-up.
T2E Exit Door Interlock tripped during ready state.
T2F Exit Door Interlock tripped during a fault state.
T2G Exit Door Interlock tripped during an auto drum maintenance cycle.
T2H Exit Door Interlock tripped during Printhead maintenance.
T2J Exit Door Interlock tripped during Printhead purge.
T2K
Exit Door Interlock tripped during an oil Transfix Roller cycle.
T2L Exit Door Interlock tripped during standby mode.
T2M Exit Door Interlock tripped during pick from Tray 2.
T2N Exit Door Interlock tripped during pick from Tray 3.
T2P
Exit Door Interlock tripped during pick from Tray 4.
T2Q Exit Door Interlock tripped during pick from Tray 1.
T2R Exit Door Interlock tripped during duplexing.
T2S Exit Door Interlock tripped during transfix staging.
T2T
Exit Door Interlock tripped during transfixing.
T2X Exit Door Interlock tripped during paper exit.
T2Z Exit Door Interlock tripped during shutdown.
1. Check for supported media.
2. Check system grounds.
3. Run the Monitor Sensors test using Service Diagnostics.
4. Check the Exit Door Interlock Switch. Replace if necessary
5. Check the Drum Maintenance Kit is functioning properly and the blade is not cov-
ered with ink debris. Replace if necessary
6. Replace the Transfix Roller
V2D Tray 2 Paper Size Switch activated during warm-up.
V2E Tray 2 Paper Size Switch activated during ready state.
V2F Tray 2 Paper Size Switch activated during a fault state.
V2K Tray 2 Paper Size Switch activated during an oil Transfix Roller cycle.
V2L Tray 2 Paper Size Switch activated during standby mode.
V2M Tray 2 Paper Size Switch activated during pick from Tray 2.
V2N Tray 2 Paper Size Switch activated during pick from Tray 3.
V2P Tray 2 Paper Size Switch activated during pick from Tray 4.
V2Q Tray 2 Paper Size Switch activated during pick from Tray 1.
V2R Tray 2 Paper Size Switch activated during duplexing.
V2S Tray 2 Paper Size Switch activated during transfix staging.
V2T Tray 2 Paper Size Switch activated during transfixing.
V2X Tray 2 Paper Size Switch activated during paper exit.
1. Check system grounds.
2. Check that the Tray 2 media guides are set correctly.
3. Run the Monitor Sensors test using Service Diagnostics.
4. Check the Paper Size Switch. Replace if necessary
5. Replace the Pivot Arm.
Error Messages and Codes
Jam Codes
(REP 6.0.2).
(REP 2.0.12).
(REP 6.0.7).
Table 3 Jam Code Troubleshooting
Code Description / Procedure
W2D Tray 3 Paper Size Switch activated during warm-up.
W2E Tray 3 Paper Size Switch activated during ready state.
W2F Tray 3 Paper Size Switch activated during a fault state.
W2L Tray 3 Paper Size Switch activated during standby mode.
W2M Tray 3 Paper Size Switch activated during pick from Tray 2.
W2N Tray 3 Paper Size Switch activated during pick from Tray 3.
W2P Tray 3 Paper Size Switch activated during pick from Tray 4.
W2Q Tray 3 Paper Size Switch activated during pick from Tray 1.
W2R Tray 3 Paper Size Switch activated during duplexing.
W2V Tray 3 Paper Size Switch activated during an auto drum maintenance cycle.
W2S Tray 3 Paper Size Switch activated during transfix staging.
W2T Tray 3 Paper Size Switch activated during transfixing.
W2X Tray 3 Paper Size Switch activated during paper exit.
1. Check system grounds.
2. Check that the Tray 3 media guides are set correctly.
3. Run the Monitor Sensors test using Service Diagnostics.
4. Replace the 525-Sheet Feeder.
W4N Tray 3 Paper Size Switch activated during pick from Tray 3.
W4P Tray 3 Paper Size Switch activated during pick from Tray 4.
W2S Tray 3 Paper Size Switch activated during pick from Tray 1.
1. Check system grounds.
2. Check that the Tray 3 media guides are set correctly.
3. Run the Monitor Sensors test using Service Diagnostics.
4. Replace the 525-Sheet Feeder.
X2A Tray 3 pick flag actuated during an abnormal shutdown.
X2B Tray 3 pick flag actuated during a normal shutdown.
X2C Tray 3 pick flag actuated during mechanical recovery
X2D Tray 3 pick flag actuated during warm-up.
X2E Tray 3 pick flag actuated during ready state.
X2F Tray 3 pick flag actuated during a fault state.
X2L Tray 3 pick flag actuated during standby mode.
X2M Tray 3 pick flag actuated during pick from Tray 2.
X2N
Tray 3 pick flag actuated during pick from Tray 3.
X2P Tray 3 pick flag actuated during pick from Tray 4.
X2Q Tray 3 pick flag actuated during pick from Tray 1.
X2R Tray 3 pick flag actuated during duplexing.
X2S
Tray 3 pick flag actuated during transfix staging.
X2V Tray 3 pick flag actuated during an auto drum maintenance cycle.
X2W Tray 3 pick flag actuated during drum imaging.
X2X Tray 3 pick flag actuated during paper exit.
1. Check system grounds.
2. Check that the Tray 2 media guides are set correctly
3. Run the Monitor Sensors test using Service Diagnostics.
4. Replace the 525-Sheet Feeder.
5. Replace the Pivot Arm.
09/2007
2-58
Initial Issue
Phaser 8860/8860MFP Service Manual