Roland VersaCamm SP-540V Service Notes page 107

E R V I C E M E N U
P R E H E A T T E M P .
E R V I C E M E N U
H E A T T I M E O U T
E R V I C E M E N U
F R A M E B A C K
4
E R V I C E M E N U
Y T E M W I T C H
This menu is for changing the functions of the machine. Normally, it is not necessary to change any switches.
Each bit can be selected with [ ] and [ ] keys and it can be changed with [
There are 8 pages of 8 bit System Switch.
Page
1
2
3
6
7
10
12
E R V I C E M E N U
H I T O R Y M E N U
E R V I C E M E N U
R E P O R T
P R E H E A T T E M P .
3 5 C 3 5 C
This menu is used for setting the preheat temperature of the print heater.
In this menu, the temperature of [PREHEAT] under the [PREHEATING] in the USER MENU can be set.
The range which user can set by [HEATER CONFIG] becomes more than the temperature set in this menu.
H E A T T I M E O U T
O F F 1 0 m i n
OFF,10~30min
This menu is used for setting time to display a check message during temperature control of the print heater when printing starts.
When temperature control is not completed even if time passes, and printing cannot be started, the message of "CHECK HEATER
VOLTAGE SETTING" is displayed.
F R A M E B A C K
E T V A L U E [ m m ]
F R A M E B A C K
E T D E F A U L T
It is the function in which only the quantity set up here at the time of a sheet setup pulls back media.
Firmware with this function Keep in mind that a setting value is 0.0mm (with no pull back) when downloading.
Y T E M W I T C H
P A G E 1 : 0 0 0 0 0 0 0 0
b i t # [ 8 7 6 5 4 3 2 1 ]
Bit Contents
1 Deactivation of Front Cover Sensor
2 Deactivation of I/S Cover Sensor
7 Deactivation of Preset function for Bi-direction adjustment
1 Acceleration of cutting operation
5 Cartridge exchange during printing
1 Deactivation of heater
2 Heater-related settings for printing test patterns
3
8 Heater operation in the service mode
3 Support of water-based ink mode
5 Position alignment lines with crop marks
8 Support of white ink
3 Support of SP-540V/300V
6
1 Support of new type pump
2 Support of water-based ink with new type pump
*All the default of the items not shown here is [0].CAUTION:The machine may make unexpected mote when the Bits not shown here are changed.
H I T O R Y M E N U
M O T O R G R O U P
All the records regarding the usage of the machine will be displayed. When [ ] and [
pressed, each title will be displayed on the top row and the parameters will be displayed on the bottom
row. Refer to the table on the next pages. Each parameter can be cleared when the [ENTER] key is pressed
while the CLEAR is displayed in the menu.
R E P O R T
E R V I C E R E P O R T
R E P O R T
H I T O R Y R E P O R T
R E P O R T
I N K C R T R E P O R T
R E P O R T
E R I A L
- Service Report will be printed. Information necessary for service activity will be printed together with
the system report. It will be printed in A4 size with either left or right head.
- History Report will be printed.
- Serial Report Menu will be printed through the RS-232C Serial with the special tool.
(9600bps, N, 8, 1 Xon/Xoff)
OFF, 20~40 C
Default : 20 min
E T V A L U E [ m m ]
0 . 0
Setting value : 0.0 mm-2000.0 mm
Default : 20 min
Setting value : 950.0mm
Y T E M W I T C H
P A G E 8 : 0 0 0 0 0 0 0 0
] and [
1 : Front Cover is always regarded as closed.
1 : I/S Cover is always regarded as closed.
0 : Preset function for Bi-direction adjustment is disabled.
1 : Acceleration of cutting operation decreases.
1 : Printing continues for 5 seconds without pausing even if ink cartridge is removed.
0 : Heater is disabled.
1 : The settings of [FULL WIDTH S] and [SCAN INTERVAL] are applied to all the test pattern printings.
1 : Heater operates even if the machine is on with the service mode.
1 : Water-based ink mode is supported.
1 : Position alignment lines are printed with crop marks.
1 : White ink is supported by enabling relevant functions.
1 : SP-540V/300V
0 : SP-300
1 : New type pump is supported.
0 : Old type pump is supported.
1 : Water-based ink is supported with new type pump.
H O T C O U N T 1
2 6 1 0 3 K h o t
E R V I C E R E P O R T
H E A D H 1
E R V I C E R E P O R T
H E A D H 1
I N K C R T R E P O R T
H E A D H 1
4-10
0 . 0
] keys.
Setting
H O T C O U N T 1
C L E A R
] keys are
Revised 11
Default Setting
0
0
1
0
0
1
0
0
0
SP-540VS 1
SP-540V 0
0
0
1
1
depends
depends