Symbols - Extron electronics ISS 506 User Manual

Symbols

Symbols (X/ values), defined below, are used throughout the discussions of the
switcher-initiated messages that begin on the next page and the command/
response table that begins on page 4-12. The symbols represent variables in the
switcher-initiated messages and the command/response table fields.
] = CR/LF (carriage return/line feed) (hex 0D 0A)
} = CR (no line feed)
• = Space
E
= Escape key
X!
= Input number 1 through 6
X@
= Output number 1 (program) or 2 (preview)
X#
= "Take" effect:
00 = Cut
01 = Dissolve
02 = Wipe
X$
= Preview switch mode: 0 = swap mode, 1 = stay mode
X%
= Video type:
1 = RGB 6 = S-video
2 = YUV-HD 7 = Composite
3 = YUVp 8 = SDI (input 6 only)
4 = RGBcvS 9 = HD-SDI (input 6 only)
5 = YUVi
X^
= Switcher resolution:
01 = 640x480 11 = 1366x768
02 = 800x600 12 = 1365x1024
03 = 852x480 13 = 1400x1050
04 = 1024x768 14 = 1600x1200
05 = 1024x852 15 = 480p
06 = 1024x1024 16 = 576p
07 = 1280x768 17 = 720p
08 = 1280x1024 18 = 1080i
09 = 1360x765 19 = 1080p
10 = 1365x768
X&
= Video refresh rate:
1 = 50 Hz 4 = 96 Hz
2 = 60 Hz 5 = 100 Hz
3 = 72 Hz 6 = 120 Hz
X*
= Output video type:
0 = RGBHV 2 = YUV bi-level
1 = RGsB 3 = YUV tri-level
X(
= Output sync polarity:
0 = H–/V– 2 = H+/V–
1 = H–/V+ 3 = H+/V+
X1)
= 0 = off, 1 = on
X1!
= RGB delay/effect duration
(00 [RGB delay] or 01 [effect] to 50) in 0.1 second
increments
X1@
= Size value (up to 4095)
X1#
= Position value (up to 4095)
X1$
= Vertical start Range depends on the input format
X1%
= Horizontal start Range depends on the input format
X1^
= Pixel sampling phase (000 thru 031)
X1&
= Total pixels Range depends on the input format
X1*
= Active pixels Range depends on the input format
X1(
= Active lines Range depends on the input format
X2!
= Preset number (01 thru 03)
X2@
= Input preset 1 - 128
ISS 506 Integration Seamless Switcher • SIS
X2#
X2$
03 = Title key
04 = PIP
X2%
X2^
X2&
X2*
X2(
X3)
X3!
X3@
X3#
X3$
X3%
X3^
X3&
X3*
= Execute Auto Image Program output / Preview Output
01 = yes
02 = no
03 = yes
= Color (000 through 127)
Tint (000 through 127)
Brightness (000 through 127)
Contrast (000 through 127)
Detail value (000 through 127)
= Program/preview output selection
Prog/Prev Prog/Prev
0 = Off/Off 2 = Off/On
1 = On/Off 3 = On/On
= Test pattern type (1 through 10)
00 = Color Bars 06 = Crop
01 = crosshatch 4:3 07 = Aspect ratio 1.33
02 = 4x4 crosshatch 08 = Aspect ratio 1.78
03 = Split gray scale 09 = Aspect ratio 1.85
04 = Ramp 10 = Aspect ration 2.35
05 = Alternating pixels
= Gain value Numeric dB value, 0 to +24
= Gain/attenuation -18 dB to +24 dB, each step = 1 dB
= Attenuation value Numeric dB value, -1 to -18
= Volume adjustment range 0 - 100 (percent)
= Effect status 1 = selected
= Subeffect:
00 = Cut (PIP only) 13 = Soft plus out
01 = Dissolve (PIP only) 14 = Hard right
02 = Soft right 15 = Hard left
03 = Soft left 16 = Hard up
04 = Soft up 17 = Hard down
05 = Soft down 18 = Hard center in
06 = Soft center in 19 = Hard center out
07 = Soft center out 20 = Hard curtain in
08 = Soft curtain in 21 = Hard curtain out
09 = Soft curtain out 22 = Hard square in
10 = Soft square in 23 = Hard square out
11 = Soft square out 24 = Hard plus in
12 = Soft plus in 25 = Hard plus out
= Luma and color key level
000 - 255
= PIP or Title status 1 = on (displayed)
0 = off (not displayed)
= Logo filename nnnn.bmp
Logo filenames can be up to 16 alphanumeric
N
characters, including the ".bmp" extension. You
must include the ".bmp" extension for the ISS to
recognized the file as a logo.
The blank (space bar) character as the value of
switches the logo to a black screen.
= Logo number 1 or 2
= Logo recall key type 0 = level
= PIP audio setting 1 = follow main window
2 = follow PIP window
Programming and Control
™
/ no
/ yes
/ yes
0 = deselected
X3%
1 = color
4-5