Table of Contents
Advertisement
Ethernet connection
The cable can be terminated as either a patch cable or a crossover cable (figure 4-2)
and must be properly terminated for your application:
•
•
Default address
To access the switcher via the Ethernet port, you need the switcher's IP address. If
the address has been changed to an address comprised of words and characters, the
actual numeric IP address can be determined using the front panel (see "IP
information" in chapter 3, Operation) or the Ping utility (see "Pinging to determine
the switcher's IP address" or "Pinging to determine the Web IP address" in
appendix A, "Ethernet Connection", for more details). If the address has not been
changed, the factory-specified default is 192.168.254.254.
Symbols
Symbols (
switcher-initiated messages that begin on the next page and the command/
response table that begins on page 4-9. The symbols represent variables in the
switcher-initiated messages and the command/response table fields.
= CR/LF (carriage return/line feed) (hex 0D 0A)
= CR (no line feed)
•
= Space
= Escape key
Esc
= Input number (1 through 8)
X1
= Output number (1 [program] or 2 [preview])
X2
= 0 = off, 1 = on
X3
= Take level: 0 = video and audio, 1 = video, 2 = audio
X4
= Video type:
X5
0
= RGB
5
= Betacam 60
1
= RGBcvS
6
= HDTV
2
= YUVi
7
= S-video
3
= YUVp
8
= Composite
4
= Betacam 50
= Switcher resolution:
X6
00 = 640x480
09 = 1365x1024
01 = 800x600
10 = 720p*
02 = 832x624
11 = 1080p
03 = 848x480
12 = 1080i
04 = 852x480
13 = 1400 x 1050
05 = 1024x768*
14 = 576p
06 = 1280x768*
15 = 1366x768
07 = 1280x1024*
16 = 1365x768
08 = 1360x765
* Native DVI resolution.
= Video refresh rate:
X7
0
= 50 Hz
3
= 75 Hz
1
= 56 Hz
4
= 85 Hz
2
= 60 Hz
5
= AFL*
Lock or AFL is Accu-RATE Frame Lock
(PAL = 50 Hz, NTSC = 59.94 Hz).
= Output video type: 0 = RGBHV, 1 = RGBS
X8
= Output sync polarity:
X9
0
= H–/V–
2
= H+/V–
1
= H–/V+
3
= H+/V+
Patch (straight) cable — Connection of the ISS to an Ethernet hub, router, or
switcher that also hosts a controlling computer
Crossover cable — Direct connection between the ISS and a computer
values), defined below, are used throughout the discussions of the
Xn
X10
X11
X12
X13
X14
X15
X16
X17
X18
X19
X20
X21
X22
X23
X24
X25
X26
X27
X28
™
X29
ISS 408 Integration Seamless Switcher • Programmer's Guide
= Color value (0 thru 127)
= Tint value (0 thru 255)
= Brightness and contrast value (0 thru 63)
= Size value (range depends on the resolution)
= Centering value (range depends on the resolution)
= Blanking value (000 thru 200)
= Pixel sampling phase (000 thru 031)
= Horizontal filter value (0 thru 3)
= Vertical filter or composite/S-video detail filter (1 thru 7)
= Preset number (01 thru 03)
= RGB delay/dissolve speed (00 [RGB] or 01 [dissolve] to 50)
= Program/preview output selection
Prog/Prev
Prog/Prev
0 = Off/Off
2 = Off/On
1 = On/Off
3 = On/On
= Test pattern type (001 through 010)
001 = Color Bars
006 = alternating pixels
002 = crosshatch
007 = film aspect ratio 1.78
003 = 4x4 crosshatch 008 = film aspect ratio 1.85
004 = gray scale
009 = film aspect ration 2.35
005 = crop
010 = ramp
= Gain/attenuation: -24dB to +•9 dB, each step = 1 dB
= Gain value: Numeric dB value, 0 to +9
=Attenuation value: Numeric dB value, -1 to -24
= Preview switch mode: 0 = stay mode, 1 = swap mode
= Frequency: nnn.nn (kHz [horizontal] or Hz [vertical])
= Detected input signal standard (0 through 4)
0 = none
3 = NTSC 4.43
1 = NTSC 3.58
4 = SECAM
2 = PAL
Dash (–) = not applicable (occurs when the input is
set for RGB or progressive YUV).
= "Take" effect: 00 = cut, 01 = dissolve
4-3
Advertisement
Table of Contents
