The Drawer Drive Motor Does Not Operate; The Registration Clutch Does Not Operate; The Upper Paper Feed Clutch Does Not Operate; The Lower Paper Feed Clutch Does Not Operate - Kyocera Mita KM-1530 Service Manual

2AV/X
Problem
(7)
Cooling fan motor 3
does not operate.
(8)
The drawer drive
1
motor* does not
operate.
(9)
The registration
clutch does not
operate.
(10)
The upper paper
feed clutch does not
operate.
1-5
(11)
The lower paper
1
feed clutch* does
not operate.
(12)
Paper feed clutch
4
(ST) 1* does not
operate.
(13)
Paper feed clutch
4
(ST) 2* does not
operate.
(14)
The bypass paper
feed clutch does not
operate.
(15)
The cleaning lamp
does not turn on.
*1: Optional for 15 cpm copier.
*4: Optional for both 20 cpm and 15 cpm copiers.
1-5-26
Causes
Broken cooling fan motor 3
coil.
Poor contact in the cooling
fan motor 3 connector
terminals.
Broken drawer drive
1
motor* coil.
Poor contact in the drawer
1
drive motor* connector
terminals.
Broken registration clutch
coil.
Poor contact in the
registration clutch
connector terminals.
Broken upper paper feed
clutch coil.
Poor contact in the upper
paper feed clutch
connector terminals.
Broken lower paper feed
1
clutch* coil.
Poor contact in the lower
1
paper feed clutch*
connector terminals.
Broken paper feed clutch
4
(ST) 1* coil.
Poor contact in paper feed
4
clutch (ST) 1* connector
terminals.
Broken paper feed clutch
4
(ST) 2* coil.
Poor contact in paper feed
4
clutch (ST) 2* connector
terminals.
Broken bypass paper feed
clutch coil.
Poor contact in the bypass
paper feed clutch
connector terminals.
Poor contact in the
cleaning lamp connector
terminals.
Defective cleaning lamp.
*2: For 20 cpm copier only. *3: Optional for 220-240 V specifications of 15 cpm copier.
Check procedures/corrective measures
Check for continuity across the coil. If none, replace cooling fan
motor 3.
Reinsert the connector. Also check for continuity within the
connector cable. If none, repair or replace the cable.
Check for continuity across the coil. If none, replace the drawer
1
drive motor* .
Reinsert the connector. Also check for continuity within the
connector cable. If none, repair or replace the cable.
Check for continuity across the coil. If none, replace the
registration clutch.
Reinsert the connector. Also check for continuity within the
connector cable. If none, remedy or replace the cable.
Check for continuity across the coil. If none, replace the upper
paper feed clutch.
Reinsert the connector. Also check for continuity within the
connector cable. If none, remedy or replace the cable.
Check for continuity across the coil. If none, replace the lower
1
paper feed clutch* .
Reinsert the connector. Also check for continuity within the
connector cable. If none, remedy or replace the cable.
Check for continuity across the coil. If none, replace paper feed
4
clutch (ST) 1* .
Reinsert the connector. Also check for continuity within the
connector cable. If none, remedy or replace the cable.
Check for continuity across the coil. If none, replace paper feed
4
clutch (ST) 2* .
Reinsert the connector. Also check for continuity within the
connector cable. If none, remedy or replace the cable.
Check for continuity across the coil. If none, replace the bypass
paper feed clutch.
Reinsert the connector. Also check for continuity within the
connector cable. If none, remedy or replace the cable.
Reinsert the connector. Also check for continuity within the
connector cable. If none, remedy or replace the cable.
Check for continuity. If none, replace the cleaning lamp.