Icom IC-7000 Instruction Manual page 68

4
RECEIVE AND TRANSMIT
■ Operating FM
q Push [
Y Y ( )]/[
BAND
band or push a band key on the HM-151.
w Push [MODE] momentarily or push and hold for 1
sec. to select FM mode.
• After FM, WFM or AM mode is selected, push [MODE]
for 1 sec. to select from FM, WFM and AM modes.
e Rotate [DIAL] to tune in a desired signal.
• The S-meter indicates received signal strength when a
signal is received.
• The default tuning step for FM mode is 1 kHz; this can
be changed using the tuning step program mode. (p. 30)
r Rotate [AF] to set audio to a comfortable listening
level.
t Push [PTT] (microphone) to transmit.
• [TX] indicator lights red.
y Speak into the microphone at your normal voice
level.
• Adjust 'MIC Gain' at this step, if necessary. (p. 38)
u Release [PTT] (microphone) to return to receive.
D Convenient functions for receive
• Preamp and attenuator (p. 72)
➥ Push [P.AMP/ATT] momentarily to turn the pre-
amp ON or OFF.
• " " appears when the preamp is set to ON.
➥ Push and hold [P.AMP/ATT] for 1 sec. to turn the
attenuator ON.
• Push [P.AMP/ATT] momentarily to turn the attenuator
OFF.
• " " appears when the attenuator is set to ON.
• Auto notch filter (p. 80)
➥ Push [ANF/• REC] to turn the auto notch filter ON
and OFF.
• " " appears when the auto notch filter is set to ON.
D Convenient functions for transmit
• VOX (voice operated transmit) (p. 83)
➥ While "M M - - 3 3 " is selected, push [F-1 V V O O X X ] to turn
the VOX function ON and OFF.
• Push and hold [MENU/GRP] for 1 sec. once or twice
to select the menu group M M .
• Push [MENU/GRP] momentarily one or more times
to select the menu M M - - 3 3 .
• "VOX" appears when the VOX function is set to ON.
➥ While "M M - - 3 3 " is selected, push [F-1 V V O O X X ] for 1
sec. to enter the VOX set mode.
• Push [F-1 ≤ ≤ ]/[F-2 ≥ ≥ ] to select an item.
• Rotate [DIAL] to set the value/conditions.
59
)] to select the desired
Z Z (
BAND [AF] [MODE] [TX] indicator
"FM" appears
• DSP noise reduction (p. 79)
➥ Push [NR/LEV] to turn the DSP noise reduction
ON and OFF.
• " " appears when the DSP noise reduction is set to
ON.
➥ Push and hold [NR/LEV] for 1 sec. to enter the
noise reduction level set mode, then rotate [DIAL]
to adjust the DSP noise reduction level.
• VSC (voice squelch control) (p. 82)
➥ While "S S - - 1 1 " is selected, push [F-4 V V S S C C ] to turn
the VSC function ON and OFF.
• " " appears when VSC function is set to ON.
• Transmit quality monitor (p. 87)
)], then [F-4 O O T T H H ] to enter the mis-
➥ Push [AF(
SET
cellaneous (others) set mode. Select an item with
[F-1 ≤ ≤ ]/[F-2 ≥ ≥ ], then rotate [DIAL] to turn the
monitor function ON and OFF.
[Y]
[Z]
[DIAL]