Icom IC-7000 Instruction Manual page 15

DURING FM/WFM OPERATIONS:
VOX DUP
F-1 F-2
VOX FUNCTION (p. 83)
➥ Push momentarily to toggle the VOX func-
VOX
tion ON and OFF.
F-1 • " " appears when the VOX function is
ON.
➥ Push and hold for 1 sec. to enter the VOX
set mode.
• The VOX gain, ANTI-VOX and VOX delay
can be set in VOX set mode.
✔ What is the VOX function?
The VOX function (voice operated transmission) activates
the transmitter when you speak into the microphone and au-
tomatically returns to receive when you stop speaking.
SPEECH COMPRESSOR (p. 87)
➥ Push momentarily to toggle the speech
COM
compressor ON and OFF.
F-2
• " " appears when the speech compres-
sor is ON.
➥ Push and hold for 1 sec. to enter the com-
pression level set mode.
• Speech compression can be adjusted in
compression level set mode.
AGC (p. 74)
➥ Push to change the time constant of the
AGC
AGC circuit.
F-3
• " ," "
the fast time constant, middle time constant
or slow time constant is selected, respec-
tively.
➥ Push and hold for 1 sec. to enter the AGC
set mode.
• " " (OFF) can be selected.
TBW (p. 84)
➥ Push momentarily to indicate the selected
TBW
TX filter width.
F-4
• The popup indicator appears.
➥ Push and hold for 1 sec. to toggle the TX
filter width between narrow, middle or
wide.
• The following filters are specified as the de-
fault. Each filter width can be set in the quick
set mode. (pgs. 121, 122)
WIDE : 100 Hz to 2900 Hz
MID : 300 Hz to 2700 Hz
NAR : 500 Hz to 2500 Hz
TON 9600
F-3 F-4
" or " " appears when
PANEL DESCRIPTION
BREAK-IN FUNCTION (p. 85)
➥ Push momentarily to select semi break-in,
BRK
full break-in (QSK) and break-in OFF.
F-1
• " " or "
semi break-in or full break-in, respectively.
• An external switch, such as a foot switch,
must be connected to the ACC socket (pin 3,
pin 7 or RTTY SEND—see p. 23) if break-in
is turned OFF.
➥ Push and hold for 1 sec. to enter the
break-in delay time set mode.
✔ What is the break-in function?
Full break-in (QSK) activates the receiver between transmit-
ted dots and dashes. This is useful when operating in nets,
or during DX pile-ups and during contests, when "fast re-
sponses" are common.
1/4 FUNCTION
1/4
Push to toggle the 1/4-speed tuning func-
tion ON and OFF in CW and RTTY
F-2 modes.
1
• When the ⁄
4
and fine tuning can be used.
DUPLEX FUNCTION (p. 63)
➥ Push to select the duplex transmit offset
DUP
direction or turn the function OFF.
➥ Push and hold for 1 sec. to turn the one-
F-2
touch repeater function ON/OFF.
FM TONE OPERATION
➥ Push momentarily to set the subaudible
TON
tone encoder for repeater use, tone
F-3 squelch function, DTCS and OFF.
• " " appears when the repeater tone
function is ON. (p. 63)
• " " appears when the tone squelch func-
tion is ON. (p. 60)
• " " appears when the DTCS squelch
function is ON. (p. 61)
➥ Push and hold for 1 sec. to enter the tone
frequency or DTCS code set mode. (pgs.
60, 61)
• Tone scan function is also available. (p. 62)
➥ Push and hold to transmit a 1750 Hz tone
when pushing and holding [PTT]. (p. 67)
9600 MODE
9600
Push to turn the 9600 bps data transmis-
sion mode ON and OFF. (p. 116)
F-4
1
" appears when selecting
function is ON, " " appears
1
6