Icom IC-7000 Instruction Manual page 152

17
CONTROL COMMAND
• Command table (continued)
Command Sub command
0E B0
B1
D0
D3
0F 00
01
10
11
12
10 00
01
02
03
04
05
06
07
08
09
10
11 —
13 00
01
02
14 01 + Level data [AF] level setting (0=max. CCW to
02 + Level data [RF] level setting (0=max. CCW to
03 + Level data [SQL] level setting (0=11 o'clock to
06 + Level data NR level setting (0=min. to
07 + Level data Inside [PBT] setting or IF shift
08 + Level data Outside [PBT] setting
09 + Level data CW Pitch
0A + Level data RF Power setting (0=mini. to
0B + Level data MIC Gain setting (0=mini. to
0C + Level data Key Speed setting (0=slow to
0D + Level data NOTCH (NF1) frequency setting
0E + Level data COMP Level setting (0=0 to
0F + Level data Break-IN DELAY setting (20=2.0d
12 + Level data NB
15 + Level data Monitor gain setting (0=0 to
16 + Level data VOX
143
Description
Set as non-select channel
Set as select channel
Set scan resume OFF
Set scan resume ON
Turn the split function OFF
Turn the split function ON
Select simplex operation
Select –DUP operation
Select +DUP operation
AM/FM/WFM modes:
Select 10 Hz tuning step
SSB/CW/RTTY modes: TS OFF
Select 100 Hz tuning step
Select 1 kHz tuning step
Select 5 kHz tuning step
Select 9 kHz tuning step
Select 10 kHz tuning step
Select 12.5 kHz tuning step
Select 20 kHz tuning step
Select 25 kHz tuning step
Select 100 kHz tuning step
AM/FM/WFM modes:
Select MHz step
SSB/CW/RTTY modes: Invalid
Select/read attenuator (0=OFF,
12=ON (12 dB))
Announce with voice synthesizer
(00=all data; 01=frequency and
S-meter level; 02=receive mode)
255=max. CW)
255=11 o'clock)
255=max. CW)
255=max.)
setting (0=max. CCW, 128=cen-
ter, 255=max. CW)
(0=max. CCW, 128=center,
255=max. CW)
setting (0=300 Hz,
128=600 Hz, 255=900 Hz, in 5 Hz
steps)
255=max.)
255=max.)
255=fast)
(0=low freq. to 255=high freq.)
10=10)
to 130=13.0d)
level setting (0=0
255=100%)
255=100%)
gain setting (0=0
255=100%)
Command Sub command
14 17 + Level data Anti-VOX gain setting (0=0 to
18 + Level data Contrast (LCD) setting (0=0 to
19 + Level data Bright (LCD) setting (0=0 to
1A + Level data NOTCH (NF2) frequency setting
15 01
02
11
12
13
14
16 02
12
22
40
41
42
43
44
45
46
47
48
4B
4C
4F
50
51
19 00
1A 00
01
02
03
04
050001
050002
050003
050004
to
050005
050006
to
Description
255=100%)
255=100%)
255=100%)
(0=low freq. to 255=high freq.)
Read squelch condition
Read S-meter level
Read RF power meter
Read SWR meter
Read ALC meter
Read COMP meter
Preamp (0=OFF; 1=ON)
AGC selection
(1=Fast; 2=Mid; 3=Slow)
Noise blanker (0=OFF; 1=ON)
Noise reduction (0=OFF; 1=ON)
Auto notch (0=OFF; 1=ON)
Repeater tone (0=OFF; 1=ON)
Tone squelch (0=OFF; 1=ON)
Speech compressor (0=OFF; 1=ON)
Monitor (0=OFF; 1=ON)
VOX function (0=OFF; 1=ON)
Break-in (0=OFF; 1=semi break-
in; 2=full break-in)
Manual notch (NF1) (0=OFF; 1=ON)
DTCS (0=OFF; 1=ON)
VSC (0=OFF; 1=ON)
Twin Peak Filter (0=OFF; 1=ON)
Dial lock function (0=OFF, 1=ON)
Manual notch (NF2) (0=OFF, 1=ON)
Read the transceiver ID
Send/read memory contents (see
p. 146 for details)
Send/read band stacking register
contents (see p. 146 for details)
Send/read memory keyer contents
(see p. 146 for details)
Send/read the selected filter width
(SSB, CW, RTTY:
0=50 Hz to 40/31=3600/2700 Hz;
AM: 0=200 Hz to 49=10 kHz)
Send/read the selected AGC time
constant (0=OFF, 1=0.1/0.3 sec. to
13=6.0/8.0 sec.)
RF Power setting (0=mini. to
255=max.)
MIC Gain setting (0=mini. to
255=max.)
Send/read of SSB TX bandwidth
(lower edge) for wide
(0=100, 1=200, 2=300, 3=500 HZ)
Send/read of SSB TX bandwidth
(higher edge) for wide (0=2500,
1=2700, 2=2800, 3=2900 HZ)
Send/read of SSB TX bandwidth
(lower edge) for middle
(0=100, 1=200, 2=300, 3=500 HZ)
Send/read of SSB TX bandwidth
(higher edge) for middle (0=2500,
1=2700, 2=2800, 3=2900 HZ)