Icom IC-7000 Instruction Manual page 11

✔ What is the PBT control?
PBT electronically narrows the IF passband width to reject
interference. This transceiver uses DSP to implement PBT.
➥ While M-ch/RIT is selected:
● Rotate the inner control to select a memory
●
channel number (p. 100).
● Push and hold inner control for 1 sec. to turn
●
the RIT/∂TX mode ON (pgs. 73, 86).
• Push [Z Z (
/
MENU GRP
● While the RIT/∂TX mode is OFF: ●
Rotate outer control to select a memory bank
(p. 104).
● While the RIT/∂TX is ON:
●
Rotate outer control to shift the receive or
transmit frequency (pgs. 73, 86).
• " " or " " indicators appear when the RIT or
∂TX function is activate, respectively.
• The shift frequency range is ± 9.999 kHz in 1 Hz
∂TX
steps (or ±9.99 kHz in 10 Hz steps).
RIT
M-ch
Channel Channel
decreases increases
• When the RIT or ∂TX function is ON, push and
hold [F-1 R R I I T T ] or [F-2 ∂ ∂ T T X X ] for 1 sec. to add or
subtract the frequency shift to the display fre-
quency.
✔ What is the RIT function?
RIT (Receiver Incremental Tuning) shifts the receive fre-
quency without shifting the transmit frequency.
This is useful for fine tuning for stations calling you off fre-
quency or when you prefer to listen to slightly different-
sounding voice characteristics, etc.
✔ What is the ∂ ∂ TX function?
The ∂TX shifts the transmit frequency without shifting the re-
ceive frequency. This is useful for simple split frequency op-
eration in CW, etc.
)] to exit the RIT/∂TX mode.
RIT
M-ch
RIT
Frequency Frequency
decreases increases
PANEL DESCRIPTION
y TWIN PBT (M-ch/RIT) INDICATOR
(pgs. 73, 77, 86, 100)
➥ Indicates the status of [PBT/M-ch/RIT] (t) as the
Twin PBT function or memory channel/RIT con-
trol.
• Indicator is green when the Twin PBT is selected.
• Indicator is off when the M-ch/RIT is selected.
• Indicator is orange when the RIT or ∂TX function is
activate.
u MENU/GROUP KEYS [MENU/GRP] (p. 151)
➥ Push either key one or more times to select
menus within a menu group (M M , S S or G G (Graphic)).
➥ Push and hold for 1 sec. to select one of the three
menu groups: M M - - 1 1 to M M - - 3 3 , S S - - 1 1 to S S - - 3 3 and G G - - 1 1
(Scope) to G G - - 3 3 (SWR meter).
i TUNER/CALL KEY [TUNER/CALL]
➥ During HF/50 MHz operation (p. 114):
● Push momentarily to toggle the automatic an-
●
tenna tuner function ON and OFF.
• An optional antenna tuner must be connected.
• " " indicator appears when the tuner is ON.
● Push and hold for 2 sec. to manually tune the ●
antenna.
• An optional antenna tuner must be connected.
• " " indicator appears when the tuner is ON.
➥ During 144/430 MHz operation (p. 100):
Push momentarily to select the call channel (or
return to the previous channel/frequency when
the call channel is already selected).
• "C1" is the 144 MHz call channel and "C2" is the 430
MHz call channel.
o MULTI-FUNCTION KEYS [F-1]/[F-2]/[F-3]/[F-4]
➥ Push to select the function indicated in the LCD
display above these keys. (pgs. 5–8, 151)
• Functions vary depending on the active menu.
Functions appear
See the illustration of the Front panel on page i-2.
1
1
2