Table of Contents
Advertisement
Contents
Part I: Introduction..................................................................7
1.0
Documentation Conventions.....................................7
1.1
Type Styles Used..................................................7
1.2
Notes, Cautions, and Warnings ............................7
1.3
Other Conventions ................................................7
1.4
Scope of Document ..............................................7
2.0
Specifications............................................................8
2.1
Environmental Specifcations.................................8
2.2
Voltage Input to Control Panel ..............................8
2.3
Power Outputs ......................................................8
2.4
Minimum Operating Voltage .................................8
2.5
Data Bus ..............................................................8
2.6
Keypads ................................................................8
3.0
Standard Features ....................................................8
3.1
Communicator.......................................................8
3.2
Zones ....................................................................8
3.3
Areas and Accounts..............................................8
3.4
Programmable Outputs.........................................8
3.5
Users.....................................................................8
3.6
Keyswitch/Exit Terminator ....................................8
3.7
Alarm Event Memory ............................................8
3.8
History Log............................................................9
3.9
Wireless (RF) Devices ..........................................9
4.0
Control Panel Assembly............................................9
5.0
Listings and Approvals..............................................9
6.0
System Options.........................................................9
6.1
Arming Devices.....................................................9
6.2
Data Bus Devices .................................................9
6.3
RF Devices .........................................................10
6.4
Programming Tools.............................................10
7.0
System Batteries.....................................................10
7.1
Standby Battery ..................................................10
7.2
RAM Backup Battery...........................................10
8.0
Available Power ......................................................10
8.1
Auxiliary Power ...................................................10
8.2
Alarm Power .......................................................10
9.0
Installer Keypad Connector.....................................10
Part II: System Installation and Setup.................................11
10.0
Control Panel Installation ........................................11
10.1
Electro Magnetic Interference (EMI) ...................11
10.2
Enclosure Mounting ............................................12
10.3
System Battery Installation .................................12
11.0
Telephone Connections ..........................................13
12.0
Phone Line Fault.....................................................13
13.0
Communication Failure (Comm Fail) ......................13
14.0
Arming Device Installation ......................................14
14.1
Keypad................................................................14
14.2
Keyswitch............................................................15
15.0
On-board Sensor Loop Setup .................................16
15.1
Overview .............................................................16
15.2
Tamper-wired Zone Configuration ......................16
15.3
No EOL Zone Configuration................................16
15.4
Four-wire Smoke Detector Configuration ...........16
16.0
On-board Output Setup...........................................16
16.1
Overview .............................................................16
16.2
Programmable Output 1 (PO 1) ..........................17
16.3
Programmable Outputs 2-4 (PO 2- PO 4) ..........17
17.0
RF3227E RF Receiver Setup .................................18
17.1
RF Receiver Addressing .....................................18
17.2
RF3227E Installation...........................................18
17.3
RF3227E Programming ......................................18
17.4
RF Receiver Supervision ....................................18
Page 4
P/N: 4998152533-02
Copyright 2007 Bosch Security Systems, Inc.
18.0
Off-board Sensor Loops (DX2010)......................... 18
18.1
DX2010 (DX2013/DX2014) Overview ................ 18
18.2
DX2010 Installation ............................................ 18
18.3
DX2010 Wiring ................................................... 19
18.4
DX2010 Auxiliary Output Connections ............... 20
18.5
DX2010 Tamper Input Connections ................... 21
18.6
DX2010 Tamper-wired Configuration................. 21
18.7
DX2010 Addressing ........................................... 21
18.8
DX2010 Status LED ........................................... 22
18.9
DX2010 Supervision........................................... 22
19.0
Off-board Outputs (DX3010) .................................. 22
19.1
Overview............................................................. 22
19.2
DX3010 Configuration ........................................ 22
19.3
DX3010 Relay Outputs....................................... 22
19.4
DX3013 Installation ............................................ 23
19.5
DX3010 Wiring ................................................... 24
19.6
DX3010 Address Programming.......................... 25
19.7
DX3010 Supervision........................................... 25
20.0
RS-232 Serial Interface (DX4010i/DX4010)........... 25
20.1
DX4010i/DX4010 Overview................................ 25
20.2
DX4010i/DX4010 Installation ............................. 25
20.3
RPS Direct Connection ...................................... 26
20.4
DX4010i/DX4010 Configuration Jumpers .......... 27
20.5
DX4010i/DX4010 Addressing............................. 27
20.6
DX4010i/DX4010 Supervision............................ 27
20.7
DX4010i/DX4010 DB9 Connector ...................... 28
21.0
Network Interface Module (DX4020) ...................... 28
21.1
DX4020 Overview .............................................. 28
21.2
DX4020 Addressing ........................................... 28
21.3
DX4020 Installation ............................................ 28
21.4
DX4020 Wiring ................................................... 30
21.5
DX4020 Programming ........................................ 30
21.6
DX4020 Ethernet/Serial Status LEDs................. 31
21.7
DX4020 Supervision........................................... 31
22.0
Door Access Control Module (DACM).................... 31
22.1
DACM Overview ................................................. 31
22.2
DACM Wiring...................................................... 31
22.3
DACM Supervision ............................................. 32
23.0
System Power Up................................................... 32
24.0
System Status LED ................................................ 32
25.0
Installer Keypad...................................................... 33
26.0
Installer Mode ......................................................... 33
27.0
Installer Menu ......................................................... 33
27.1
Bell Test.............................................................. 33
27.2
Strobe Test ......................................................... 33
27.3
Battery Test ........................................................ 33
27.4
Test Report......................................................... 33
27.5
Zone Status ........................................................ 34
27.6
Output Test......................................................... 34
27.7
RF Menu............................................................. 34
27.8
Always Force Arm .............................................. 36
27.9
Keypad Test ([#][9][1]) ........................................ 37
Part III: How to Program....................................................... 38
28.0
Keypad Programming............................................. 38
28.1
Installer Mode/Installer Menu ............................. 38
28.2
Expert/Installer Programming Modes ................. 38
28.3
Parameter Addresses......................................... 38
28.4
Text Entry Addresses ......................................... 40
28.5
Exit Programming Mode ..................................... 40
DS7200V2-UK Installer's Guide
Hide quick links:
Advertisement
Chapters
Table of Contents
