Yamaha A3000 Owner's Manual page 343

20: TWah+Drum Set (TOUCH WAH+DIST), 21: TWah+OD (TOUCH WAH+ODRV)
1 Sensitive 0~127
2 Cutoff Freq Offset 0~127
3 Resonance 1.0~12.0
4 Drive 0~127
5 PostDrive EQ Low -12~+12dB
6 PostDrive EQ Mid -12~+12dB
7 PostDrive LPF Freq 1.0kHz~thru
8 Drive Output Level 0~127
9 EQ Low Frequency 32Hz~2.0kHz
10 EQ Low Gain -12~+12dB
11 EQ High Frequency 500Hz~16.0kHz
12 EQ High Gain -12~+12dB
13 Dry/Wet Balance D63>W ~ D=W ~ D<W63
22: Dist (DISTORTION), 23: OverDrv (OVERDRIVE)
1 Drive 0~127
2 EQ Low Frequency 32Hz~2.0kHz
3 EQ Low Gain -12~+12dB
4 LPF Cutoff 1.0kHz~Thru
5 Output Level 0~127
6 Edge 0~127
7 EQ Mid Frequency 100Hz~10.0kHz
8 EQ Mid Gain -12~+12dB
9 EQ Mid Width 1.0~12.0
10 Dry/Wet Balance D63>W ~ D=W ~ D<W63
24: AmpSim (AMP SIMULATOR)
1 Dry/Wet Balance D63>W ~ D=W ~ D<W63
2 Drive 0~127
3 AMP Type Off, Stack, Combo, Tube
4 LPF Cutoff 315Hz~Thru
5 Edge 0~127
6 Output Level 0~127
25: Comp (COMPRESSOR)
1 Threshold -48~-6dB
2 Attack 1~40ms
3 Release 10~680ms
4 Ratio 1.0~20.0
5 Output Level 0~127
26: Comp+Drum Set (COMP+DIST)
1 Drive 0~127
2 LPF Cutoff Freq 1.0k~Thru
3 Output Level 0~127
4 Edge 0~127
5 Attack 1ms~40ms
6 Release 10ms~680ms
7 Threshold -48dB~-6dB
8 Ratio 1.0~20.0
9 EQ Low Frequency 32Hz~2.0kHz
10 EQ Low Gain -12~+12dB
11 EQ Mid Frequency 100Hz~10.0kHz
12 EQ Mid Gain -12~+12dB
13 EQ Mid Width 1.0~12.0
14 Dry/Wet Balance D63>W ~ D=W ~ D<W63
Sensitivity at which the wah filter will change in response to the input level
Offset value for the wah filter control frequency
Bandwidth of the wah filter
(Distortion) Degree of distortion
(Distortion) Gain by which the EQ will boost/cut the low range
(Distortion) Frequency at which the filter will cut the high range
(Distortion) Frequency at which the filter will cut the high range
(Distortion) Output leve
Frequency at which the EQ will boost/cut the low range
Amount of gain by which the EQ will boost/cut the low range
Frequency at which the EQ will boost/cut the high range
Amount of gain by which the EQ will boost/cut the high range
Balance between the dry sound and effect sound
Degree of distortion
Frequency at which the EQ will boost/cut the low range
Gain with which the EQ will boost/cut the low range
Frequency at which the filter will cut the high range
Output level
Curve of distortion characteristics (sharp (127): distortion begins suddenly;
mild (0): distortion begins gradually)
Frequency at which the EQ will boost/cut the mid range
Gain with which the EQ will boost/cut the mid range
Width of the area in which the EQ will boost/cut the mid range
Balance between the dry sound and the effect sound
Balance between dry sound and effect sound
Degree of distortion
Select the type of amp to be simulated
Frequency at which the low pass filter will cut the high range
Curve of distortion characteristics (sharp (127): distortion begins suddenly;
mild (0): distortion begins gradually)
Output level
Input level at which compression begins to be applied
Time until when the compressor begins to take effect
Time until the compressor effect disappears
Compression ratio of the compressor
Output level
Degree of distortion
Frequency at which the filter will cut the high range
Output level
Curve of distortion characteristics (sharp (127): distortion begins suddenly;
mild (0): distortion begins gradually)
(Compressor) Time until when the compressor begins to take effect
(Compressor) Time until the compressor effect disappears
(Compressor) Input level at which compression begins to be applied
(Compression) Compression ratio of the compressor
Frequency at which the EQ will boost/cut the low range
Gain with which the EQ will boost/cut the low range
Frequency at which the EQ will boost/cut the mid range
Gain with which the EQ will boost/cut the mid range
Width of the mid range area which the EQ will boost/cut
Balance of the dry sound and effect sound
Effect parameter list
Appendix
341