Effect Parameter List - Yamaha A3000 Owner's Manual

Effect parameter list

This section explains the meaning of each parameter in each effect.
The tables give the parameter number, the range of settings (or selections), and the explanation.
1: Scratch (DIGITAL SCRATCH)
1 Input Level 0~127
2 Initial Delay 0.1~460.0ms
3 Scratch Speed 1~127
4 Scratch Depth 0~127
5 Auto Pan Speed 0.00Hz~39.7Hz
6 Auto Pan Depth 0~127
7 EQ Mid Frequency 100Hz~10.0kHz
8 EQ Mid Gain -12~+12dB
9 EQ Mid Width 1.0~12.0
10 HPF Frequency Thru~8.0kHz
11 Dry/Wet Balance D63>W ~ D=W ~ D<W63
2: AutoSyn (AUTO SYNTH)
1 Mod Speed 0~127
2 Mod Wave Type typeA, typeB, typeC, typeD
3 Mod Depth 0~127
4 Mod Depth Ofst R -64~+63
5 LPF Frequency 1.0kHz~Thru
6 HPF Frequency Thru~8.0kHz
7 Dry Mix Level 0~127
8 Delay Time 0.1~370.0ms
9 Delay Time Ofst R -884~0
10 Feedback Level -63~+63
11 FB Level Ofst R -63~+63
12 Delay Level 0~127
13 AM Speed 0~127
14 AM Wave tri, sine, saw up, saw down
15 AM Depth 0~127
16 AM Inverse R "normal, inverse"
3: TechMod (TECH MODULATION)
1 Mod Speed 0~127
2 Mod Depth 0~127
3 Pre Mod HPF Freq Thru~8.0kHz
4 Mod Gain -12~+12dB
5 Mod LPF Frequency 1.0kHz~Thru
6 Mod LPF Resonance 1.0~12.0
7 Mod Mix Balance D63>W ~ D=W ~ D<W63
8 Delay Time 0.1~740.0ms
9 Delay Time Ofst R -884~0
10 Feedback Level -64~+63
11 FB Level Ofst R -64~+63
12 Feedback Hi Damp 0.1~1.0
13 FB Hi Damp Ofst R -0.9~+0.9
14 Dry/Wet Balance D63>W ~ D=W ~ D<W63
Scratch depth
Delay time
Scratch modulation frequency
Scratch modulation depth
Autopan frequency
Autopan depth
Frequency at which the EQ will boost/cut the mid range
Gain by which the EQ will boost/cut the mid range
Width of the mid range area boosted/cut by the EQ
Frequency at which the high pass filter will cut the low range
Balance between dry sound and effect sound
Modulation speed
Modulation type
Modulation depth
R ch offset relative to modulation depth
Frequency at which the low pass filter will cut the high range
Frequency at which the high pass filter will cut the low range
Add dry sound before the delay input
Delay time
Delay time offset for the R ch offset
Feedback amount
Feedback offset for the R ch
Delay level
Modulation frequency
Select modulation waveform
Amplitude modulation depth
Left/right phase reversal of the amplitude modulation signal
Modulation speed
Modulation depth
Frequency at which the high pass filter will cut the low range
Gain of the modulation signal
Frequency at which the low pass filter will cut the high range
Resonance of the low pass filter
Balance between the effect sound and the dry sound before the delay input
Delay time
Delay time offset for the R ch
Feedback amount
Feedback offset for the R ch
Adjust the high range attenuation (lower values will cause the high range to decay
faster)
High Damp offset for the R ch
Balance between the dry sound and effect sound
Effect parameter list
Appendix
337