Yamaha A3000 Owner's Manual page 340

Effect parameter list
4: NoisDly (NOISY MOD DELAY)
1 Dry/Wet Balance
2 Mod Speed
3 Mod Wave Type
4 Mod Depth
5 Delay Time
6 Feedback Level
7 Mod Mix Balance
8 Hi Gain
9 HPF Frequency
5: FlngPan (PLANGING PAN)
1 Dry/Wet Balance
2 Flange&Pan Speed
3 Flanger Depth
4 Flanger Delay
5 Flanger Feedback
6 FlangPan Delay
7 FlangPan Feedback
8 HPF Frequency
9 LPF Frequency
10 Delay Time
11 Delay Feedback
12 Delay Level
13 AM Speed
14 AM Wave
15 AM Depth
16 AM Inverse R
6: FlowPan (FLOW PAN)
1 Dry/Wet Balance
2 Delay Time
3 Delay Time Ofst R
4 Feedback Level
5 FB Level Ofst R
6 Feedback Hi Damp
7 FB Hi Damp Ofst R
8 Delay Mod Speed
9 Delay Mod Depth
10 Delay Dry/Wet
11 PreDelayPan Speed
12 PreDelayPan Wave
13 PreDelayPan Depth
14 Auto Pan Speed
15 Auto Pan Wave
16 Auto Pan Depth
7: NoisAmb (NOISE AMBIENT)
1 Dry/Wet Balance
2 Mod Speed
3 Mod Depth
4 Noise Level
5 LPF Frequency
6 Dry Mix Level
7 Delay Time
8 Delay Time Ofst R
9 Feedback Level
10 Delay Level
11 AM Speed
12 AM Wave
13 AM Depth
14 AM Inverse R
Appendix
338
D63>W ~ D=W ~ D<W63
0~127
typeA, typeB, typeC, typeD
0~127
0.1~650.0ms
-63~+63
1~127
-12~+12dB
Thru~8.0kHz
D63>W ~ D=W ~ D<W63
0.00Hz~39.7Hz
0~127
0.1~180.0ms
-63~+63
0.1~180.0ms
-63~+63
Thru~8.0kHz
1.0kHz~Thru
0.1~270.0ms
-63~+63
0~127
0.00Hz~39.7Hz
tri, sine, saw up, saw down
0~127
normal, inverse
D63>W ~ D=W ~ D<W63
0.1~650.0ms
-884~0
-63~+63
-63~+63
0.1~1.0
-0.9~+0.9
0.00Hz~39.7Hz
0~127
1~127
0.00Hz~39.7Hz
tri, sine
0~127
0.00Hz~39.7Hz
tri, sine
0~127
D63>W ~ D=W ~ D<W63
0~127
0~127
0~127
1.0kHz~Thru
0~127
0.1~370.0ms
-884~0
-63~+63
0~127
0.00Hz~39.7Hz
tri, sine, saw up, saw down
0~127
normal, inverse
Balance between the dry sound and the effect sound
Delay modulation frequency
Modulation type
Modulation depth
Delay time
Feedback amount
Balance between delay sound and delay bypass sound
Gain by which the EQ will boost/cut the high range
Frequency at which the high pass filter will cut the low range
Balance between the dry sound and the effect sound
Delay modulation frequency
Delay modulation depth
Delay time
Feedback amount
Delay time
Feedback amount
Frequency at which the high pass filter will cut the low range
Frequency at which the low pass filter will cut the high range
Delay time
Feedback amount
Delay level
Frequency of amplitude modulation
Select amplitude modulation waveform
Amplitude modulation depth
Invert left/right phase of amplitude modulation signal
Balance between delay sound and effect sound
Delay time
Offset of R ch delay time
Feedback amount
Offset of R ch feedback
Adjust the high range attenuation (lower values will cause the high range to decay
faster)
Offset of R ch high damp
Delay modulation frequency
Delay modulation depth
Balance between delay sound and effect sound
Frequency of the pre-delay autopan
Waveform of the pre-delay autopan
Depth of the pre-delay autopan
Autopan frequency
Autopan waveform selection
Autopan depth
Balance between dry sound and effect sound
Modulation speed
Modulation depth
Level of noise component
Frequency at which the low pass filter will cut the high range
Pre-delay dry level
Delay time
Delay time offset for the R ch
Feedback amount
Delay level
Modulation frequency
Modulation waveform selection
Depth of amplitude modulation
Invert left/right phase of amplitude modulation signal