Yamaha A3000 Owner's Manual page 341

8: LoReso (LOW RESOLUTION)
1 Mod Depth 0~127
2 Mod Delay Offset 1~127
3 Mod Feedback -64~+63
4 Resolution 1, 1/2~1/128
5 Mod Mix Balance 0~127
6 Phase Inverse R off, wet, wet+dry
7 Dry/Wet Balance D63>W ~ D=W ~ D<W63
9: Noisy (NOISY)
1 Drive 0~127
2 Mod Depth 1~10
3 Mod Speed 0~127
4 Mod Feedback -63~+63
5 AM Speed 0.00Hz~39.7Hz
6 AM Depth 0~127
7 Mod Mix Balance 1~127
8 LPF Frequency 1.0kHz~Thru
9 LPF Resonance 1.0~12.0
10 EQ Frequency 100Hz~10.0kHz
11 EQ Gain -12~+12dB
12 EQ Width 1.0~12.0
13 Dry/Wet Balance D63>W ~ D=W ~ D<W63
10: AtkLoFi (ATTACK LOFI)
1 Sensitive 0~127
2 Resolution 1, 1/2~1/32
3 Peak Frequency 100Hz~10.0kHz
4 LPF Frequency 1.1kHz~Thru
5 Flanger Speed 0.00Hz~39.7Hz
6 Flanger LFO Wave tri, sine, saw up, saw down
7 Flanger Depth 0~127
8 Fln Depth Ofst R -64~+63
9 Flanger Delay 0.1~650ms
10 Fln Delay Ofst R -884~0
11 Flanger Feedback -63~+63
12 Flanger FB Ofst R -63~+63
13 Flanger FB HiDamp 0.1~1.0
14 FB HiDamp Ofst R -0.9~+0.9
15 Fln Mix Balance 1~127
16 Dry/Wet Balance D63>W ~ D=W ~ D<W63
11: Radio (RADIO)
1 Noise Level 0~127
2 Tone 0~127
3 Mod LPF Frequency 1.0kHz~Thru
4 Mod HPF Resonance 1.0~12.0
5 HPF Frequency Thru~8.0kHz
6 LPF Frequency 1.0kHz~Thru
7 Dry/Wet Balance D63>W ~ D=W ~ D<W63
12: TurnTbl (DIGITAL TURNTABLE)
1 Click Density 0~5
2 Click Level 0~127
3 Noise Tone 0~6
4 Noise Mod Speed 0.00Hz~39.7Hz
5 Noise Mod Depth 0~127
6 Dry Send to Noise 0~127
7 Noise LPF Freq 1.0kHz~Thru
8 Noise LPF Q 1.0~12.0
9 Noise Level 0~127
10 Dry LPF Frequency 1.0kHz~Thru
11 Dry Level 0~127
Modulation depth
Modulation delay offset
Feedback amount
Resolution
Balance between modulation sound and modulation bypass sound
Left/right phase reversal
Balance between dry sound and effect sound
Degree of distortion
Modulation depth
Modulation speed
Feedback amount
Amplitude modulation frequency
Amplitude modulation depth
Balance between noise modulated sound and bypass sound
Frequency at which the low pass filter will cut the high range
Resonance of the low pass filter
Frequency at which the EQ will boost/cut the mid range
Gain by which the EQ will boost/cut the mid range
Width of the mid range area which the EQ will boost/cut
Balance between the dry sound and effect sound
Sensitivity
Resolution
Frequency at which a peak will be created in the mid range
Frequency at which the low pass filter will cut the high range
Frequency of delay modulation
Modulation waveform selection
Modulation depth
R ch offset for depth
Delay time
R ch offset for delay time
Feedback amount
R ch offset for feedback
Adjust the high range attenuation (low values will cause the high range to decay
faster)
R ch offset for high damp
Balance between flanger sound and bypass sound
Balance between dry sound and effect sound
Degree of noise modulation
Tone of noise modulation
Frequency at which the low pass filter will cut the high range
Resonance of high pass filter
Frequency at which the high pass filter will cut the low range
Frequency at which the low pass filter will cut the high range
Balance between dry sound and effect sound
Frequency with which the click sounds will occur
Level of the click sounds
Tone of noise
Amplitude modulation frequency of the noise
Amplitude modulation depth of the noise
Mixture of dry signal into the noise
Frequency at which the low pass filter will cut the high range
Low pass filter resonance
Noise level
Frequency at which the low pass filter will cut the high range
Level of the dry sound
Effect parameter list
Appendix
339