Yamaha A3000 Owner's Manual page 342

Effect parameter list
13: Jump (JUMP)
1 Depth
2 Speed
3 Direction
4 Type
5 Jump Wave Type
6 Resolution
7 LPF Frequency
8 HPF Frequency
9 Dry/Wet Balance
14: BeatChg (BEAT CHANGE)
1 BeatChange(Ctrl)
2 Beat Range
3 PitchChange(Ctrl)
4 Pitch Range
5 Accuracy Type
6 EQ Frequency
7 EQ Gain
8 EQ Width
9 Dry/Wet Balance
• You can use this effect to set up a controller so that the controller will vary the playback speed while leaving the pitch unchanged. To set this up, first
select the program, then go the program's EfType page ( 121) and set one of the program effects (Effect 1, 2, or 3) to BeatChg. Then go to the program's
PgmCtl page ( 136), select the desired controller (Device), and set its Function to EF x -1 (where x is the Effect number: 1, 2, or 3). Then go to the effects
editing page ( 124) and set this effect's Beat Range parameter to an appropriate value. Leave the BeatChange (Ctrl) and PitchChange (Ctrl) values set to
0, so that the effect operates only in response to the controller input.
• Note that this effect may not operate as expected if you apply it to the input signal or if you select it for more than one of the A3000's three effect blocks.
15: VceCncl (VOICE CANCELLER)
1 Low Adjust
2 High Adjust
16: 3BandEQ 3 BAND EQ)
1 EQ Low Frequency
2 EQ Low Gain
3 EQ Mid Frequency
4 EQ Mid Gain
5 EQ Mid Width
6 EQ High Gain
7 EQ High Frequency
8 Input Mode
17: Exciter (AURAL EXCITER)
1 HPF Cutoff Freq
2 Drive
3 Mix Level
18: AWah+Drum Set (AUTO WAH + DIST), 19: AWah+OD (AUTO WAH+ODRV)
1 LFO Frequency
2 LFO Depth
3 Cutoff Freq Offset
4 Resonance
5 Drive
6 PostDrive EQ Low
7 PostDrive EQ Mid
8 PostDrive LPF Freq
9 Drive Output Level
10 EQ Low Frequency
11 EQ Low Gain
12 EQ High Frequency
13 EQ High Gain
14 Dry/Wet Balance
Appendix
340
0~127
0~127
L<>R, L>>R
typeA, typeB, typeC
typeA, typeB, typeC, typeD
1, 1/2~1/256
1.0k~Thru
Thru~8.0kHz
D63>W ~ D=W ~ D<W63
-63~+63
0~12
-63~+63
0~12
sound4~normal~rhythm4
100Hz~10.0kHz
-12~+12dB
1.0~12.0
D63>W ~ D=W ~ D<W63
0~26
0~26
50Hz~2.0kHz
-12~+12dB
100Hz~10.0kHz
-12~+12dB
1.0~12.0
-12~+12dB
500Hz~16.0kHz
mono/stereo
Aural Exciter is a registered trademark of Aphex Systems, Ltd., and is manufactured under license.
500Hz~16.0kHz
0~127
0~127
0.00Hz~39.7Hz
0~127
0~127
1.0~12.0
0~127
-12~+12dB
-12~+12dB
1.0kHz~thru
0~127
32Hz~2.0kHz
-12~+12dB
500Hz~16.0kHz
-12~+12dB
D63>W ~ D=W ~ D<W63
Modulation depth
Modulation speed
Modulation type
Modulation type
Modulation type
Resolution
Frequency at which the low pass filter will cut the high range
Frequency at which the high pass filter will cut the low range
Balance between the dry sound and effect sound
Special parameter which allows a controller to modify the beat change
Width of variation for sample playback speed
Special parameter which allows a controller to modify the pitch change
Width of variation for Pitch Change
Balance between emphasis on sound quality and emphasis on sense of beat
Frequency at which the EQ will boost/cut the mid range
Gain by which the EQ will boost/cut the mid range
Width of the area in which the EQ will boost/cut the mid range
Balance between the dry sound and effect sound
Adjust the frequency of the lower limit of the mid range that will be attenuated.
Adjust the frequency of the upper limit of the mid range that will be attenuated.
Frequency at which the EQ will boost/cut the low range
Amount of gain by which the EQ will boost/cut the low range
Frequency at which the EQ will boost/cut the low range
Amount of gain by which the EQ will boost/cut the mid range
Width of the area in which the EQ will boost/cut the mid range
Amount of gain by which the EQ will boost/cut the high range
Frequency at which the EQ will boost/cut the high range
Mono/stereo input mode selection
Frequency at which the high pass filter will cut the low range of the effect sound
Degree with which the exciter effect will be applied
Level at which the effect sound will be mixed into the dry sound
Frequency at which the wah filter will be controlled
Depth at which the wah filter will be controlled
Offset value for the wah filter control frequency
Bandwidth of the wah filter
(Distortion) Degree of distortion
(Distortion) Gain by which the EQ will boost/cut the low range
(Distortion) Gain by which the EQ will boost/cut the mid range
(Distortion) Frequency at which the filter will cut the high range
(Distortion) Output level
Frequency at which the EQ will boost/cut the low range
Amount of gain by which the EQ will boost/cut the low range
Frequency at which the EQ will boost/cut the high range
Amount of gain by which the EQ will boost/cut the high range
Balance between the dry sound and effect sound