Siemens SINUMERIK 840D sl Function Manual page 330

Data descriptions
9.1 Machine data for SINUMERIK 840D sl
11415
Meaning:
Special cases, errors,...
330
$MN_SUPPRESS_ALARM_MASK_2
Screen form for suppressing special alarm outputs.
Bit set: The corresponding alarm (warning) is not triggered.
Bit hex. Meaning
Value
=====================================================================
0: 0x1 16773 "Channel %1 Axis %3 is following axis. The axis/spindle inhibits of the leading
axes are different"
1: 0x2 2100 "NCK battery warning level reached"
2101 "NCK battery alarm"
2102 "NCK battery alarm"
2: 0x4 2120 "NCK fan alarm" (ineffective on modules that are designed not to require a fan)
3: 0x8 15120 "PowerFail: Show buffer overflow"
4: 0x10 15187 "Error during execution of PROGEVENT file"
5: 0x20 15188 "Error when executing ASUB file"
6: 0x40 26120 "$AA_ESR_ENABLE = 1 and axis should become neutral"
26121 "Axis is neutral and $AA_ESR_ENABLE should be set =1"
26123 "$AA_ESR_ENABLE = 1 should be set, however $MA_ESR_REACTION is not set"
26124 "$AC_TRIGGER initiated, however axis is neutral, ESR ignores this axis"
7: 0x80 10724 "Software limit at the start of the block violated"
10734 "Working area limitation violated at the start of the block "
10737 "WCS working area limitation violated at the start of the block"
8: 0x100 14008 "WRITE command in /_N_EXT_DIR"
10734 "Working area limitation violated at the start of the block "
10737 "WCS working area limitation violated at the start of the block"
9: 0x200 14006 "Invalid program name"
10: 0x400 4006 "Maximum number of axes that can be activated exceeded"
11: 0x800 16017 "LIFTFAST ignores this axis, as it cannot be used for the current axis type"
12: 0x1000 22025 "Channel %1 Block %2 Following axis/spindle %3 Synchronism (2): Fine
tolerance exceeded"
- exception: The alarm is generated if for the following axis/spindle involved, CPMALARM[FAx]
Bit 8 = 0 is programmed.
22026 "Channel %1 Block %2 Following axis/spindle %3 Synchronous operation (2): Coarse
tolerance exceeded"
- exception: The alarm is generated if for the following axis/spindle involved, CPMALARM[FAx]
bit 9 = 0 is programmed.
13: 0x2000 22001 "Braking ramp longer than Stop D time."
22002 "Braking ramp longer than Stop D time for gear stage %3 Reason %4."
14: 0x4000 16963 "ASUB start refused."
15: 0x8000 21751," Limit velocity %2 degrees/min at the modulo axis %1 exceeded (incorrect
cam output)"
21752," Axis %1 Minimum cam width cams %3 fallen below for active velocity %2"
16: 0x10000 17212 "Channel %1 tool management: Load manual tool %3, Duplo no. %2 to
spindle/toolholder"
17214 "Channel %1 Tool management: Unload manual tool %3 from spindle/toolholder %2"
17215 "Channel %1 tool management: Unload manual tool %3 from the buffer magazine
location %2"
17216 "Channel %1 unload manual tool from toolholder %4 and load manual tool %3 %2"
17: 0x20000 16771 "Channel %1 Block %3 Following axis %2 Overlaid movement not enabled"
Function Manual, 12/2017, 6FC5397-4BP40-6BA1
Safety Integrated