Xerox WorkCentre 7132 Service Documentation page 1461

Chain-Link NVM Name
790-670 Blank Document Detection Fea-
ture Display Settings
790-671 Auto Resume Feature Settings 0, 1
790-672 Auto Clear Time-Out Display
Screen
790-674 Basic FAX favorite setting
(2nd row)
790-676 Separator Tray Default for Build
Separator Insertion
790-677 Side1 Cover Tray Default for
Cover
790-678 Side2 Cover Tray Default for
Cover
790-679 Side1 Cover Tray Default for
Booklet
790-680 Fax Number Double Input
Restriction
790-682 Separator Sheet Default Tray
Setting
790-683 Brightness/Contrast Settings
790-684 UI Screen Default Shortcut
Screen Settings
Chain 790-xxx Chain 810-xxx Copy Service
Chain-Link NVM Name
790-600 Poster Overlap Width
790-601 Index Paper Copy Image Shift
Amount
790-602 Default Output Face
790-604 Single Copy Output Face
Switch
790-605 Sample Copy Default
General procedures information
Controller & Fax NVM List
Setup Read/
Range Initial Value Write
0, 1 0: Do not dis- Read/
play Write
1: Auto Read/
Resume Write
0, 1 1: Follow M/C Read/
configuration Write
0~255 0: Not set Read/
Write
1~8 5: SMH Read/
Write
1~8 5: SMH Read/
Write
1~8 5: SMH Read/
Write
1~8 5: SMH Read/
Write
0, 1 0: Do not allow Read/
double input Write
0~8 5: SMH Read/
Write
-127 0 Read/
~127 Write
0, 1 0: Do not dis- Read/
play anything Write
Table 9 Copy Service
Setup
Range Initial Value Read/Write
1~25 10mm Read/Write
0~15 13mm Read/Write
0~3 Auto Read/Write
0, 1 Face Up Read/Write
0~1 0: Disable Sam- Read/Write
ple Copy
Table 8 UI
Description
0: Do not display
1: Display
0: Do not Auto Resume
1: Auto Resume
0: Maintain previous service
1: Follow M/C configuration
0: Not set,
1: 2 Sided Document Feed,
2: Monitor Report,
3: Communication Mode,
4: Send Header
1: Tray 1, 2: Tray 2, 3: Tray 3, 4: Tray 4, 5: SMH, 6: Tray 6 (HCF), 7: Tray 7 (HCF),
8: Interposer
1: Tray 1, 2: Tray 2, 3: Tray 3, 4: Tray 4, 5: SMH, 6: Tray 6 (HCF), 7: Tray 7 (HCF),
8: Interposer
1: Tray 1, 2: Tray 2, 3: Tray 3, 4: Tray 4, 5: SMH, 6: Tray 6 (HCF), 7: Tray 7 (HCF),
8: Interposer
1: Tray 1, 2: Tray 2, 3: Tray 3, 4: Tray 4, 5: SMH, 6: Tray 6 (HCF), 7: Tray 7 (HCF),
8: Interposer
0: Do not allow double input
1: Allow double input
0: Auto, 1: Tray 1, 2: Tray 2, 3: Tray 3, 4: Tray 4, 5: SMH, 6: Tray 6 (HCF),
7: Tray 7 (HCF), 8: Interposer
Refer to the FF of Copy Service Func for the setup range.
-127~127
(Because the valid range for each MCW Panel is different, the upper and lower limit values are con-
trolled through the UI Panel)
0: Do not display anything, 1: Display login screen
Description
10mm~25mm
0mm~15mm
0: Auto, 1: Output Side 2, 2: Output Side 1, 3: Output in reverse order
0: Face Up, 1: Face Down
0: Disable Sample Copy, 1: Enable Sample Copy
January 2007
6-138
Reversion 4.0
WorkCentre 7132