Xerox WorkCentre 7132 Service Documentation page 1460

Chain-Link NVM Name
790-563 Fixed Size 15 of FAX Scan Size
Input
790-564 Fixed Size 16 of FAX Scan Size
Input
790-565 Fixed Size 17 of FAX Scan Size
Input
790-566 FAX Pass Stamp UI Default
790-570 User permission settings for
PTT country modification
790-621 The display after scanning by
Scan Service is completed
790-630 No. of digits for Assumed Speed
Dial No.
790-631 Move Registration Data in
Address Book
790-632 Added Thumbnail Default
(Net Save)
790-633 Added Thumbnail Default (Mail) 0, 1
790-640 Paper Type Change Screen
Display
790-641 Paper Information Color
Attribute Display Availability
790-642 Paper Information Other
Attributes Display Availability
790-661 Report Storage Mailbox
790-662 Consumables Check Auto Dis-
play Timing Settings
790-664 Address Book Import Operation
Mode
790-665 Paper Tray Settings Screen
Access on Setup Menu
790-666 DADF Mixed Standard Size
Scan Mode Display Settings
790-667 Blank Document Detection Fea-
ture Panel Default
790-668 Allow/Prohibit JT/FT/Address
Book Registration Settings
Reversion 4.0
WorkCentre 7132
Setup Read/
Range Initial Value Write Description
1~255 118: 8.5x13 Read/ ditto
SEF Write
1~255 90: 8.5x11 Read/ ditto
SEF Write
1~255 89: 8.5x11 LEF Read/ ditto
Write
0~1 0: OFF Read/ 0: OFF, 1: ON
Write
0~2 0: Prohibited Read/ 0: Prohibited, 1: Allow for EU country settings, 2: Allow for NA country settings
Write
0~2 0: Do not dis- Read/ 0: Do not display 7sec "Scanning completed" message and "Transferring data" screen; 1: Display 7sec
play 7sec Write "Scanning completed" message but not the "Transferring data" screen; 2: Display 7sec "Scanning com-
"Scanning pleted" message and the "Transferring data" screen
completed"
message and
"Transferring
data" screen
0~6 0: Actual Read/ 0: Actual Address Book 3: 3-digit Virtual Address Book 4: 4-digit Virtual Address Book 5: 5-digit Virtual
Address Book Write Address Book 6: 6-digit Virtual Address Book (*1, 2 cannot be set up)
0~1 0: Do not Read/ 0: Do not transfer, 1: Transfer
transfer Write
0, 1 1: Add RW 0: Do not add, 1: Add
0: Do not add RW 0: Do not add, 1: Add
0~255 0: Do not dis- RW 0: Do not display, 1: Display
play
0~255 0: Do not dis- Read/ 0: Do not display, 1: Display
play Write
0~255 1: Display Read/ 0: Do not display, 1: Display applied size, 2: Display hole punch attributes, 3: Display color attributes
applied size Write
1~500 1 Read/ Mailbox No.
Write
0~2 0: Do not dis- Read/ 0: Do not display, 1: Display only after the Power ON initialization sequence has completed and the sys-
play Write tem is Ready, 2: Display every time auto clear occurred
0, 1 0: Add Mode Read/ [0: Add Mode, 1: Substitute Mode]
Write
0, 1 1: ON Read/ [0: OFF, 1: ON]
Write
0, 1 1: Display Read/ 0: Do not display, 1: Display
Write
0, 1 0: OFF Read/ [0: OFF, 1: ON]
Write
0, 1 0: Prohibit Read/ [0: Prohibit, 1: Allow]
Write
Table 8 UI
January 2007
6-137
General procedures information
Controller & Fax NVM List