E614-0073-00 System Verification Error; E614-0074-00 Start System Verification Function Error; E614-0101-00 Flash Pcb Error; E614-0111-00 Flash Pcb Error - Canon imageRUNNER ADVANCE C3500 III Series Service Manual

E614-0073-00
Detection Description
Remedy
E614-0074-00
Detection Description
Remedy
E614-0101-00
Detection Description
Remedy
E614-0111-00
Detection Description
Remedy
System verification error
At startup in safe mode, an error may occur due to invalid data of the startup firmware.
When this error occurs, the system has not been started normally. Therefore, it is not recorded in
the error log.
[Related parts]
- Flash PCB
[Remedy]
1. Replace the Flash PCB and reinstall the system using SST or a USB flash drive.
Start system verification function error
At startup in safe mode, an error may occur due to invalid data of the firmware for safe mode
startup.
When this error occurs, the system has not been started normally. Therefore, it is not recorded in
the error log.
[Related parts]
- Flash PCB
[Remedy]
1. Replace the Flash PCB and reinstall the system using SST or a USB flash drive.
Flash PCB error
An error was detected in the system area. (Initialization failed at startup or I/O error at startup)
When this error occurs, the system has not been started normally. Therefore, it may not be
recorded in the error log.
[Related parts]
- Flash PCB
- Main Controller PCB (UN05)
[Remedy] Perform the following in the order while checking whether the error is cleared. Although
the error is cleared by "HD-CHECK", it may occur again. Thus, perform Remedies 1 to 4.
1. Check the related harness/cable and connector.
2. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "0", and execute "HD-CHECK". Then,
turn OFF and then ON the main power.
3. Obtain the necessary backup data by referring to the backup data list.
[Reference] For backup and restoration, refer to "Adjustment> Main Controller System" and
"Appendix> Backup Data List" in the Service Manual.
4. After replacing the Flash PCB, reinstall the system software using SST or a USB flash drive.
5. Replace the Main Controller PCB.
[Reference] Before replacing the Main Controller PCB, back up the service mode data (approx. 2
min) and restore the backup data after the replacement so the data may be able to be protected.
- Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> RSRAMBUP
- Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> RSRAMRES
Flash PCB error
An error was detected in the system area. (File could not be written in the Flash PCB after startup
or I/O error after startup)
[Related parts]
- Flash PCB
- Main Controller PCB (UN05)
[Remedy] Perform the following in the order while checking whether the error is cleared. Although
the error is cleared by "HD-CHECK", it may occur again. Thus, perform Remedies 1 to 4.
1. Check the related harness/cable and connector.
2. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "0", and execute "HD-CHECK". Then,
turn OFF and then ON the main power.
3. Obtain the necessary backup data by referring to the backup data list.
[Reference] For backup and restoration, refer to "Adjustment> Main Controller System" and
"Appendix> Backup Data List" in the Service Manual.
4. After replacing the Flash PCB, reinstall the system software using SST or a USB flash drive.
5. Replace the Main Controller PCB.
[Reference] Before replacing the Main Controller PCB, back up the service mode data (approx. 2
min) and restore the backup data after the replacement so the data may be able to be protected.
- Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> RSRAMBUP
- Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> RSRAMRES
436
7. Error/Jam/Alarm