E5F4-8001-02: Error In The Saddle Stitcher Motor (Finisher-Aa1); E5F4-8002-02: Error In The Saddle Stitcher Motor (Finisher-Aa1); E5F6-8001-02: Error In The Saddle Paper Pushing Plate/Folding Motor (Finisher-Aa1) - Canon imageRUNNER ADVANCE C3500 III Series Service Manual

E5F4-8001-02
Detection Description
Remedy
E5F4-8002-02
Detection Description
Remedy
E5F6-8001-02
Detection Description
Remedy
Error in the Saddle Stitcher Motor (Finisher-AA1)
The saddle stitcher does not come off the Saddle Stitcher HP Sensor when the Saddle Stitcher
Motor has been driven for 1.2 seconds.
STAPLE FIN-AA1/BOOKLET FIN-AA1
[Related parts]
- Harnesses from the Saddle Stitcher HP Sensor (PS215) to the Saddle Stitcher Controller PCB
- Harnesses from the Saddle Stitcher Motor (M208) to the Saddle Stitcher Controller PCB
- Saddle Stitcher HP Sensor (PS215)
- Saddle Stitcher Motor (M208)
- Saddle Stitcher Controller PCB (PCB201)
- Finisher Controller PCB (PCB101)
[Points to note at work] When the Swing Guide Safety Switch (SW102) turns on at the detection
timing of this error, this error code may be displayed. Accordingly, perform the following work before
checking the related parts.
1. Check whether there is not the mulfunction in the swing guide unit.
2. Check whether there is not the mulfunction in the Swing Guide Safety Switch (SW102).
[Remedy] Check/replace the related harness/cable, connector and parts.
[Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing
the Parts" in the Service Manual.
Error in the Saddle Stitcher Motor (Finisher-AA1)
The Saddle Stitcher HP Sensor does not detect the saddle stitcher when the Saddle Stitcher Motor
has been driven for 1.2 seconds.
STAPLE FIN-AA1/BOOKLET FIN-AA1
[Related parts]
- Harnesses from the Saddle Stitcher HP Sensor (PS215) to the Saddle Stitcher Controller PCB
- Harnesses from the Saddle Stitcher Motor (M208) to the Saddle Stitcher Controller PCB
- Saddle Stitcher HP Sensor (PS215)
- Saddle Stitcher Motor (M208)
- Saddle Stitcher Controller PCB (PCB201)
- Finisher Controller PCB (PCB101)
[Points to note at work] When the Swing Guide Safety Switch (SW102) turns on at the detection
timing of this error, this error code may be displayed. Accordingly, perform the following work before
checking the related parts.
1. Check whether there is not the mulfunction in the swing guide unit.
2. Check whether there is not the mulfunction in the Swing Guide Safety Switch (SW102).
[Remedy] Check/replace the related harness/cable, connector and parts.
[Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing
the Parts" in the Service Manual.
Error in the Saddle Paper Pushing Plate/Folding Motor (Finisher-AA1)
The saddle paper pushing plate does not come off the Saddle Paper Pushing Plate HP Sensor
when the Saddle Paper Pushing Plate/Folding Motor has been driven for 1 second.
STAPLE FIN-AA1/BOOKLET FIN-AA1
[Related parts]
- Harnesses from the Saddle Paper Pushing Plate HP Sensor (PS208) to the Saddle Stitcher
Controller PCB
- Harnesses from the Saddle Paper Pushing Plate/Folding Motor (M204) to the Saddle Stitcher
Controller PCB
- Saddle Paper Pushing Plate HP Sensor (PS208)
- Saddle Paper Pushing Plate/Folding Motor (M204)
- Saddle Stitcher Controller PCB (PCB201)
- Finisher Controller PCB (PCB101)
[Points to note at work] When the Swing Guide Safety Switch (SW102) turns on at the detection
timing of this error, this error code may be displayed. Accordingly, perform the following work before
checking the related parts.
1. Check whether there is not the mulfunction in the swing guide unit.
2. Check whether there is not the mulfunction in the Swing Guide Safety Switch (SW102).
[Remedy] Check/replace the related harness/cable, connector and parts.
[Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing
the Parts" in the Service Manual.
411
7. Error/Jam/Alarm