E577-8002-02 Error In The Stack Delivery/Paddle Motor (Finisher-Aa1); E578-8001-02 Error In The Return Roller Lift Motor (Finisher-Aa1); E578-8002-02 Error In The Return Roller Lift Motor (Finisher-Aa1) - Canon imageRUNNER ADVANCE C3500 III Series Service Manual

E577-8002-02
Detection Description
Remedy
E578-8001-02
Detection Description
Remedy
E578-8002-02
Detection Description
Remedy
Error in the Stack Delivery/Paddle Motor (Finisher-AA1)
The Paddle HP Sensor does not detect the paddle when the Stack Delivery/Paddle Motor has
been driven for 1 second.
STAPLE FIN-AA1/BOOKLET FIN-AA1
[Related parts]
- Harnesses from the Paddle HP Sensor (PS120) to the Finisher Controller PCB
- Harnesses from the Stack Delivery/Paddle Motor (M103) to the Finisher Controller PCB
- Paddle HP Sensor (PS120)
- Stack Delivery/Paddle Motor (M103)
- Finisher Controller PCB (PCB101)
[Points to note at work] When the Swing Guide Safety Switch (SW102) turns on at the detection
timing of this error, this error code may be displayed. Accordingly, perform the following work before
checking the related parts.
1. Check whether there is not the mulfunction in the swing guide unit.
2. Check whether there is not the mulfunction in the Swing Guide Safety Switch (SW102).
[Remedy] Check/replace the related harness/cable, connector and parts.
[Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing
the Parts" in the Service Manual.
Error in the Return Roller Lift Motor (Finisher-AA1)
The return roller does not come off the Return Roller HP Sensor when the Return Roller Lift Motor
has been driven for 1 second.
STAPLE FIN-AA1/BOOKLET FIN-AA1
[Related parts]
- Harnesses from the Return Roller HP Sensor (PS121) to the Finisher Controller PCB
- Harnesses from the Return Roller Lift Motor (M111) to the Finisher Controller PCB
- Return Roller HP Sensor (PS121)
- Return Roller Lift Motor (M111)
- Finisher Controller PCB (PCB101)
[Points to note at work] When the Swing Guide Safety Switch (SW102) turns on at the detection
timing of this error, this error code may be displayed. Accordingly, perform the following work before
checking the related parts.
1. Check whether there is not the mulfunction in the swing guide unit.
2. Check whether there is not the mulfunction in the Swing Guide Safety Switch (SW102).
[Remedy] Check/replace the related harness/cable, connector and parts.
[Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing
the Parts" in the Service Manual.
Error in the Return Roller Lift Motor (Finisher-AA1)
The Return Roller HP Sensor does not detect the return roller when the Return Roller Lift Motor
has been driven for 1 second.
STAPLE FIN-AA1/BOOKLET FIN-AA1
[Related parts]
- Harnesses from the Return Roller HP Sensor (PS121) to the Finisher Controller PCB
- Harnesses from the Return Roller Lift Motor (M111) to the Finisher Controller PCB
- Return Roller HP Sensor (PS121)
- Return Roller Lift Motor (M111)
- Finisher Controller PCB (PCB101)
[Points to note at work] When the Swing Guide Safety Switch (SW102) turns on at the detection
timing of this error, this error code may be displayed. Accordingly, perform the following work before
checking the related parts.
1. Check whether there is not the mulfunction in the swing guide unit.
2. Check whether there is not the mulfunction in the Swing Guide Safety Switch (SW102).
[Points to note at work] When the Swing Guide Safety Switch (SW102) turns on at the detection
timing of this error, this error code may be displayed. Accordingly, perform the following work before
checking the related parts.
1. Check whether there is not the mulfunction in the swing guide unit.
2. Check whether there is not the mulfunction in the Swing Guide Safety Switch (SW102).
[Remedy] Check/replace the related harness/cable, connector and parts.
[Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing
the Parts" in the Service Manual.
405
7. Error/Jam/Alarm