Sub Groups (Touchmix-30 Pro Only); Sub Group - Overview - QSC TouchMix-30 Pro User Manual

Sub Nroups (TouchMix-30 Pro only)
Sub Nroup − Overview
Sub Nroup – Overview
Provides a single-screen view of frequently used
controls and indicators for the Sub Groups.
1. Overview tab – Selects the Sub Group Overview
screen.
2. Preset – Shows the currently selected Preset for
this sub group. Cannot be changed from this screen.
3. Reset – Sets all controls for the sub group to the
factory default position.
4. L/R Subs – Indicates whether or not the sub group
is assigned to the Main output.
5. Parametric EQ Nraph – A graphic representation
of the equalization curve based on the EQ settings.
The trace dims to indicate that the EQ is Out
(disengaged).
• EQ Nraph Vertical Scale – Represents audio
level from -20 dB to +20 dB.
• EQ Nraph Horizontal Scale – Represents
frequency from 20 Hz to 20 kHz.
6. EQ In – Engages / disengages the equalizer for the
sub group.
7. Aux Sends –
• Displays the system numbers and user-defi ned
names for the Aux channels.
• Adjustable sliders send signal to the associated
Aux channel output.
• Mute indicates if the channel's send to an Aux is muted or not.
8. EQ Handles – Touch, hold, and drag to change the Frequency and Gain of the associated EQ band. The frequency band button must be
engaged to see the EQ Handles.
9. Low and High Cut Filter and Frequency Bands 1, 2, 3, 4, 5, 6 – These buttons engage or disengage the associated fi lter.
To adjust the following parameters, select the fi eld then use the Master encoder or the up/down nudge buttons on a mobile device.
10. Nain, Bands 1–6 – Displays and adjusts gain (+/- 15 dB) of the frequency band.
11. Low and High Cut Filter Frequency – Displays and adjusts the knee frequency for the high and low cut fi lters.
12. Frequency Bands 1–6 frequency adjustment fi elds – Displays and adjusts the center frequency for the four parametric EQ bands.
13. Comp –
• Comp – Engages or disengages the channel's dynamics processor.
• Threshold – Displays and sets the level at which compression/limiting begins.
• Attack – Displays and sets the time it takes for the compressor/limiter to reach its maximum compression when the threshold level is
exceeded.
• Release – Displays and sets the time it takes for the compressor/limiter to cease gain reduction when signal drops below threshold.
• Ratio – Displays and sets the amount of compression applied to the signal.
• Nain – Displays and sets the overall output gain to makeup any loss after the signal is compressed.
• N.R. – Gain reduction meter shows the amount of compression applied to the signal.
14. FX Sends –
• Displays the system numbers and user-defi ned names for the FX channels.
• Adjustable sliders send signal from this channel to the associated FX processors.
15. Aux Number & Name – Displays the system numbers and user-defi ned names for the Aux mixes.
1001108-01-C
Press
Home
Sub Groups
Sub 1
Inputs 1-8
Main Mix 1
L/R
Overview EQ
2
Joe's Ears
Aux 1
Preset Ele Gtr Dyn Rock 1
Aux 2
4
Aux 2
L/R Subs L/R
Aux 3
Aux 3 EQ
5
20
Aux 4
Aux 4
10
1 1
8
Aux 5 2
2
0 3 3
Aux 5
4
4
-10
Aux 6
Aux 6
-20
20Hz 50 100 200 500 1K
Aux 7
9 1 2 3 4
Aux 7
10
0.00 0.00 0.00 0.00
Aux 8
11
120 80.0 200 500 12 1.0k
Aux 8
Aux 9
Comp FX Sends
Aux 9
13
Threshold 1 Mono Delay
Aux 10
G.R.
-12.0
Aux 10
Lush Reverb
2
Attack
Aux 11
16.0
Aux 11
3 Dense Reverb
Release
Aux 12
50.0
Aux 12
4 Pitch Shift
Ratio
Aux 13
Aux 13 4.0
5 Mono Delay
Gain
Aux 14
Aux 14 0.00
6 Lush Reverb
61
Touch Sub Touch a Sub
Group Bank Group
Overview
Comp FX Auxes Presets Setup
3
Reset
6
AUX Sends 7
20 1 Joe's Aux
10
2 Aux 2
5 5 6 6
0
3 Aux 3
-10
4 Aux 4
-20
20K
2K 5K 10K
5 6
5 Aux 5
0.00 0.00
6 Aux 6
11
3.0k 8.0k 8.0k
7 Aux 7
14
L C R
8 Aux 8
Aux 9
9
10 Aux 10
15
11 Aux 11
12 Aux 12
13 Aux 13
14 Aux 14
Touch
Overview Tab
Scene:
Default
Next
Prev
Sub 1 Main
Cue Cue
M
L C R
M
Sub Main
1 L/R
M
10 10 10 10
M
5
5
L L
M
u u
F
G
5
M
48
5
10
M
10
20
0 20 0
M
M
LR
40
40
M
∞
M
M
Mute Mute
M