Input Channel - Fx Sends; Fx Signal Flow - QSC TouchMix-30 Pro User Manual

Input Channel – FX Sends

FX Signal Flow

Input Channel − FX Sends
Controls how much of the Input channel's audio is sent
to the FX devices.
1. FX tab – Selects the FX Sends screen.
2. FX Overview button – Navigates to the FX Overview
screen for a view of all 6 FX sends from all inputs.
3. Simple button – Hides the Global FX Parameters
for simplifi ed operation.
4. Reset button – Resets the FX sliders, Pre/Post
settings, and the Pitch Correct settings. This button
does not reset the settings for the FX processors
including the Global FX Parameters on this screen.
5. FX Buses – The thumbnail representation of the
FX processor takes you to a screen where you can
select the processor for that FX send, and adjust the
parameters for the selected FX processor.
6. FX Label – The larger text identifi es the FX bus
number, and does not change. The smaller text can
be changed in the FX processor Setup screen.
7. FX Send sliders – Sets the level of audio sent from
the channel to the FX mix; "-inf" is off. The digital read-
out to the right of the slider indicates the slider setting.
8. Nlobal FX Parameters – Provides control over the
two most important parameters of the selected FX
device. The parameters will differ depending on the
selected processor.
9. Pre/Post Fader button – Selects a pre-fader or post-fader (default) pick-off point for the FX send. Changing this setting will change the pick-
off for all inputs.
10. Pitch Correct – Refer to the Pitch Correct topic.
FX Signal Flow
Input audio passes through the EQ, and Dynamics (compressor and gate). At this point you can split the audio and send it to the FX system (Pre-
fader), then the Channel Fader. Or, send the audio through the Channel Fader then split it and send it to the FX system (Post-fader).
"Dry" audio (no FX processing) continues through the Pan control to the Main L/R Fader and Main outputs.
The Pre-fader or Post-fader audio is sent to the Channel FX sends (The diagram shows just one of the FX Sends).
The FX Send slider determines how much of the channel audio is sent (or routed) to the assigned FX processor.
The FX processor works its magic on the audio and transforms the mono input into a stereo signal. The FX Master fader controls how much or how
little of the processed ("wet") signal is combined with the unprocessed ("dry") audio before going to the Main L/R fader and on to the Main L/R
Audio Input
Input Channels
NOTE!: For detailed information, refer to the
1001108-01-C
Main Mix
L/R
Joe's Monitor
Aux 1
Aux 2
Aux 2
Aux 3
Aux 3
Aux 4
Aux 4
Aux 5
Aux 5
Aux 6
Aux 6
Aux 7
Aux 7
Aux 8
Aux 8
Aux 9
Aux 9
Aux 10
Aux 10
Aux 11
Aux 11
Aux 12
Aux 12
Aux 13
Aux 13
Aux 14
Aux 14
Channel
Fader
EQ Dynamics
Pre
FX
-40 -20
Send
Block Diagram on page 122
Home
Input 1-8
In 1 FX
Inputs 1-8
Overview EQ Comp Gate
6
FX Buses
5
FX 1
Chorus
Joe's FX
-40 7 -20 -10 U
Dense Reverb
FX 2
FX 2
-40 -20 -10 U
Lush Reverb FX 3
FX 3
-40 -20 -10 U
Mono Delay
FX 4
FX 4
-20 -10 U
-40
None
FX 5
FX 5
-40 -20 -10 U
Basic Chorus
FX 6
FX 6
-40 -20 -10 U
10
Pitch Correct
Enable Key E
Channel
10 10
Pan
5
u
5
10
L C R
20
40
Post
10 10
5
u
-10 -5 U 5 10
5
10
20
FX 40
FX
Master
47
Touch
Touch a
an Input
Channel
Bank
1
FX Auxes Presets Setup
2 3 4
FX Overview Simple Reset
Pre/Post
Global FX Parameters
Fader
8 8 9
Hz
Rate Depth
10
-11.5 2.3 0.63 Pre
Sec mSec
Rev Time Initial Delay
10
-23.0 34.0 0.00 Post
m mSec
Size Pre Delay
10
-inf 1.43 0.5 Pre
%
mSec
Delay Regen
10
-inf 1.7 0.5 Pre
Param 1 Param 2
10
-inf 32 0.00 Pre
Hz
Rate Depth
10
-inf 1.5 0.5 Pre
Blend Correct
20% 8.3
Amount Rate
Dry Wet Slow Fast
Main
Main
L/R
Left
10 10
5
u
5
10
20
40
∞
Main
Right
Touch the
FX Tab
Scene:
Default
Next
Prev
In 1 Main
Cue Cue
L C R
Mic Main
1 L/R
10 10 10 10
5 5
L
u u
L
F
5
G
5
48
10
10
20 20
0 0
LR
40
40
1 2
3 4
∞ ∞
5 6
7 8
Mute Mute