Output Channels; Output Channel - Overview - QSC TouchMix-30 Pro User Manual

Output Channels

Output Channel − Overview
Output Channel – Overview
Provides a single-screen view of frequently used
controls and indicators for the output channel.
1. Overview tab – Selects the Channel Overview screen.
2. Preset – Shows the currently selected Preset for
this channel.
3. Pick-off point – (Auxes only) Determines where
the signal for the output channel is taken.
4. Delay – Controls and indicates the amount of delay
(up to 100 msec.) applied to the signal.
5. Delay In – Applies / bypasses the delay.
6. Reset – Sets all controls for the input channel to
the factory default position.
7. Description of the Current Preset
8. DCA – Indicates which DCA groups are assigned to
the channel.
9. Mute – Indicates which Mute groups control the channel.
10. Parametric EQ Nraph – A graphic representation
of the equalization curve based on the EQ settings.
When the EQ is engaged, the trace becomes
brighter.
• EQ Nraph Vertical Scale – Represents audio
level from -20 dB to +20 dB.
• EQ Nraph Horizontal Scale – Represents
frequency from 20 Hz to 20 kHz.
11. EQ Out/In – Engages / disengages the equalizer for the channel.
12. EQ Handles – Touch, hold, and drag to change the Frequency and Gain of the associated EQ band. The frequency band button must be
engaged to see the EQ Handles.
13. Aux Sends – (TouchMix-30 Pro only)
• Aux sends 9 – 14 are available for Aux Outputs 1 – 8 only,
• Displays the system numbers and user-defi ned names for the Aux channels.
• Adjustable sliders send signal to the associated Aux channel output.
• Mute indicates if the channel's send to an Aux is muted or not.
14. Low and High Cut Filter and Frequency Bands 1, 2, 3, and 4 – These buttons engage or disengage the associated fi lter.
To adjust the following parameters, select the fi eld then use the Master encoder or the up/down nudge buttons on a mobile device.
15. Nain, Bands 1, 2, 3, and 4 – Displays and adjusts gain (-15 to +15 dB) for the selected frequency band.
16. Low and High Cut Filter Frequency – Displays and adjusts the knee frequency for the high and low cut fi lters.
17. Frequency Bands 1–4 frequency adjustment fi elds – Displays and adjusts the center frequency for the four parametric EQ bands.
NOTE!: The following section can be a Compressor or Limiter depending on the Comp/Limit switch on the Comp/Limiter tab.
18. Comp –
• Comp – Engages or disengages the channel's compressor.
• Threshold – Displays and sets the level at which compression begins.
• Attack – Displays and sets the rate at which the compressor reaches its maximum compression when the threshold level is exceeded.
• Release – Displays and sets the rate at which the compressor ceases gain reduction when signal drops below threshold.
• Ratio – Displays and sets the amount of compression applied to the signal.
1001108-01-C
Home
Aux Out 1-8
Aux 1
Inputs 1-8
1
Main Mix
L/R
Overview PEQ GEQ
Feedback
2 3
Joe's Ears
Aux 1
Pre Fdr Post Fdr
Preset E10 Monitor
Aux 2
7
Aux 2
Tuned for QSC E10 Monitor DCA
Aux 3
Aux 3 PEQ 10
20
Aux 4
Aux 4
10
12
1
1
Aux 5
2 2
0 3
3
Aux 5
4
4
-10
Aux 6
Aux 6
-20
20Hz 50 100 200 500 1K
14
Aux 7
1 2 3
Aux 7 15
0.00 0.00 0.00
16
Aux 8
120 80.0 400 2.0k
Aux 8
18
Aux 9
Comp
Aux 9
Threshold
GR
Aux 10
-12.0
Aux 10
Attack
Aux 11
16.0
Aux 11
Release
Aux 12
50.0
Aux 12
Ratio
Aux 13
Aux 13 4.0
Aux 14
Aux 14
51
Select an
Select
Output
Channel
Bank
Overview
Limiter
Anti-
Auxes Presets Setup
(Comp)
4 5 6
Pre Dyn Pre All
Delay In Reset
0.00
ms
8 9
1 2 3 4 5 6 7 8 Mute Groups 1 2 3 4 5 6
11 AUX Sends 13
Out In
20
10
5
5 6 6
0
-10
-20
20K
2K 5K 10K
4
0.00
17
6.0k 8.0k
9 Aux 9
10 Aux 10
11 Aux 11
12 Aux 12
13 Aux 13
14 Aux 14
Select
Overview
Tab
Scene:
Default
Prev Next
Main
E10 Monitor
7 8
Cue Cue
Aux Main
1 L/R
10 10 10 10
5 5
C L
u u
F
AF
5
5
10
10
20
0 20 0
M
M
LR
40
40
M 1 2
3 4
∞
5 6
M
7 8
M
Mute Mute
M