Mitsubishi MELDAS MDS-C1 Instruction Manual page 134

M60S
Series Abbrev. Parameter name
No.
Spindle synchro-
nization multi-step
acceleration/
3059 sptc6
deceleration
changeover
speed 6
Spindle synchro-
nization multi-step
acceleration/
3060 sptc7
deceleration
changeover
speed 7
Magnification for
time constant
changeover
3061 spdiv1
speed 1
Magnification for
time constant
changeover
3062 spdiv2
speed 2
Magnification for
time constant
changeover
3063 spdiv3
speed 3
Magnification for
time constant
changeover
3064 spdiv4
speed 4
Magnification for
time constant
changeover
3065 spdiv5
speed 5
Magnification for
time constant
changeover
3066 spdiv6
speed 6
Magnification for
time constant
3067 spdiv7
changeover
speed 7
Phase
synchronization
3068 symtm1
start confirmation
time
Phase
synchronization
3069 symtm2
end confirmation
time
Phase
synchronization
3070 syprt
speed
3071 (Not used.)
3072 (Not used.)
3. Setup
Set the spindle speed for changing the 6th step's
acceleration/deceleration time constant.
Set the spindle speed for changing the 7th step's
acceleration/deceleration time constant.
Set the acceleration/deceleration time constant between the spindle
synchronization multi-step acceleration/deceleration changeover speed
1 (sptc1) to the spindle synchronization multi-step acceleration/
deceleration changeover speed 2 (sptc2) as a magnification in respect to
the spindle synchronization acceleration/deceleration time constant
(spt).
Set the acceleration/deceleration time constant between the spindle
synchronization multi-step acceleration/deceleration changeover speed
2 (sptc2) to the spindle synchronization multi-step
acceleration/deceleration changeover speed 3 (sptc3) as a
magnification in respect to the spindle synchronization
acceleration/deceleration time constant (spt).
Set the acceleration/deceleration time constant between the spindle
synchronization multi-step acceleration/deceleration changeover speed
3 (sptc3) to the spindle synchronization multi-step
acceleration/deceleration changeover speed 4 (sptc4) as a
magnification in respect to the spindle synchronization
acceleration/deceleration time constant (spt).
Set the acceleration/deceleration time constant between the spindle
synchronization multi-step acceleration/deceleration changeover speed
4 (sptc4) to the spindle synchronization multi-step
acceleration/deceleration changeover speed 5 (sptc5) as a
magnification in respect to the spindle synchronization
acceleration/deceleration time constant (spt).
Set the acceleration/deceleration time constant between the spindle
synchronization multi-step acceleration/deceleration changeover speed
5 (sptc5) to the spindle synchronization multi-step
acceleration/deceleration changeover speed 6 (sptc6) as a
magnification in respect to the spindle synchronization
acceleration/deceleration time constant (spt).
Set the acceleration/deceleration time constant between the spindle
synchronization multi-step acceleration/deceleration changeover speed
6 (sptc6) to the spindle synchronization multi-step
acceleration/deceleration changeover speed 7 (sptc7) as a
magnification in respect to the spindle synchronization
acceleration/deceleration time constant (spt).
Set the acceleration/deceleration time constant for the spindle
synchronization multi-step acceleration/
deceleration changeover speed 7 (sptc7) and higher as a magnification
in respect to the spindle synchronization acceleration/deceleration time
constant (spt).
Set the time to confirm that synchronization is attained before phase
synchronization control is started.
When "0" is set, the time will be 2 seconds. When "100" or less is set,
the time will be 100ms.
Set the time to wait for phase synchronization control to end as the time
for the rotation speed to reach the attainment range.
When "0" is set, the time will be 2 seconds. When "100" or less is set,
the time will be 100ms.
Set the fluctuation amount to change the synchronous spindle rotation
speed during phase synchronization control as the command speed and
rate.
When "0" is set, the amount will be 100%.
Not used. Set to "0".
Not used. Set to "0".
3 - 55
Details
Setting range
(Unit)
0 to 99999
(r/min)
0 to 99999
(r/min)
0 to 127
0 to 127
0 to 127
0 to 127
0 to 127
0 to 127
0 to 127
0 to 9999 (ms)
0 to 9999 (ms)
0 to 100 (%)
0
0