Cueup & Play - Sony MVS-3000 System User Manual

Status: Status of each device.
Operating When VTR is used When video disk
status
display
XXXX Communications
with the device are
being carried out
normally, but status
information is not
received.
Local The REMOTE/
LOCAL switch of
the device is set to
LOCAL.
Tape Out No tape is loaded.
Rec Recording.
Cue> Cueing up in the
forward direction.
Cue< Cueing up in the
reverse direction.
Eject Ejecting cassette.
Stb Off Stopped in standby
off mode.
Stop Stopped in standby
on mode.
Play Playing.
FF Fast forwarding.
Rewind Rewinding.
Shtl> Playing in the
forward direction in
shuttle mode.
Shtl< Playing in the
reverse direction in
shuttle mode.
Var> Playing in the
forward direction in
variable mode.
Var< Playing in the
reverse direction in
variable mode.
Jog> Playing in the
forward direction in
jog mode.
Jog< Playing in the
reverse direction in
jog mode.
Still Playing still image.
a) Not supported by Extended VTR.
Current: Shows timecode for current device position.
Start TC: Shows timecode for start point set on device.
Stop TC: Shows timecode for stop point set on device.
Variable: Shows the variable speed set for each device.
Delay: Shows start delay time set on device.
Mode: Shows operation mode (Loop or Recue) set for
each device.
Cueup & Play
communications
You can use the device control block or Device menu to
or Extended
save Cueup & Play settings (start point timecode, stop
VTRis used
point timecode, start delay time, and so on) for a VTR, disk
Not
recorder or Extended VTR in an effect register. By
communicating, or
recalling this register, you can operate the following
communicating but
buttons in the Flexi Pad to automatically control the VTR,
the device type
disk recorder or Extended VTR.
cannot be read.
[REWIND] button: Cue up to the start point timecode
[RUN] button: Play
Port is not open.
With this function you can also stop the VTR, disk
recorder or Extended VTR used for playback at the stop
point timecode recalled from the same register.
No file loaded.
Disk recorder (video disk communications
a)
Recording.
protocol) operation when loop /recue is set
—
When loop is set: Plays repeatedly between the start point
—
When recue is set: Automatically cues up the start point
—
—
Notes
• In an effect register set on the VTR/disk recorder
Stopped.
timeline, Cueup & Play settings are not possible. To add
Cueup & Play settings to such a register, first clear the
Playing.
VTR/disk recorder timeline setting before carrying out
—
the operation.
—
• When using a disk recorder with Cueup & Play, if you
carry out the following sequence of operations, the
—
system may freeze on the frame of the start point.
Press the [RUN] button to play to a point close to the end
of a file, stop playback, then press the [RUN] button
—
once more.
In such cases, first recall a different register, then carry
Playing in the
out the following sequence:
forward direction in
Recall the original register again, press the [REWIND]
variable mode.
button, then press the [RUN] button.
Playing in the
reverse direction in
Making and saving settings relating to
variable mode.
Cueup & Play
Playing in the
forward direction in
1
jog mode.
Playing in the
2
reverse direction in
jog mode.
—
3
and stop point.
when play reaches the stop point.
In the Flexi Pad, press the [EFF] button, turning it on.
Press the button corresponding to the region you want
to select, turning it on.
You can select more than one button.
For details about the method of region selection,
1 "Selecting regions in the Flexi Pad" (p.
Enter the number of the register to be recalled with the
numeric keypad buttons.
To search for an empty register, instead of entering a
number, press the [.] (period) button.
Control of VTRs, Extended VTRs, and Disk Recorders
150).
137