1. Manuals
  2. Brands
  3. Denwa Communications Manuals
  4. IP Phone
  5. DW-610G
  6. User manual

Denwa Communications DW-610G User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual

Advertisement

Table of Contents
loading

Related Manuals for Denwa Communications DW-610G

Summary of Contents for Denwa Communications DW-610G

  • Page 2: Safety Notices

    Safety Notices Please read the following safety notices before installing or using this phone. They are crucial for the safe and reliable operation of the device. Please use the external power supply that is included in the package. Other  powers supplies may cause damage to the phone, affect the behavior or induce noise.

  • Page 3: Table Of Contents

    Table of Content INTRODUCING DW-610G VOIP PHONE ..................... 6 DW-610G ................6 HANK YOU FOR YOUR PURCHASING ......................6 ELIVERY ONTENT ........................7 EYPAD ..................... 9 ORT FOR CONNECTING ......................9 CON INTRODUCTION ...................... 10 INTRODUCTION INITIAL CONNECTING AND SETTING ..................12 .....................
  • Page 4 4.8.2 Memo ........................ 22 4.8.3 Voice Mail ......................22 ........................22 4.10 ..................23 ROGRAMMABLE ONFIGURATION DW-610G’S OTHER FUNCTIONS ................... 26 ......................26 ANDDOWN ....................26 NONYMOUS ......................26 UTGOING ........................ 26 ........................ 26 ......................27 EDIAL ......................27 ALL COMPLETION .....................
  • Page 5 WEB ....................33 ONFIGURATION VIA 8.3.1 BASIC ........................ 33 8.3.2 Network ......................37 8.3.3 VOIP ......................... 47 8.3.4 Phone ........................ 61 8.3.5 Function Key ....................... 73 8.3.6 Maintenance ......................76 ........................84 EBOOT 8.4.1 Security ......................84 8.4.2 Logout ....................... 91 APPENDIX ........................

  • Page 6: Introducing Dw-610G Voip Phone

    Introducing DW-610G VoIP Phone Thank you for your purchasing DW-610G Thank you for your purchasing DW-610G, DW-610G is a full-feature telephone that provides voice communication over the same data network that your computer uses. This phone functions not only much like a traditional phone, allowing to place and...

  • Page 7: Keypad

    Keypad Key name Function Description Line1/2 /3/4 There are four SIP lines; user could select any one to make the call, if it has been registered. Keys combination, include functions such History/P-BOOK /DND /Menu /Del /Redial /Send / Soft key 1/2/3/4 Quit/Answer/Divert/Reject/Hold/Transfer/Conf/Clos e and so on.
  • Page 8 Access to phone book, check the record list and add new records and revise the record. When check the Directory phone book record, press this key again will return to idle mode. View the Missed call, Incoming Call and Outgoing Call. History 1.

  • Page 9: Port For Connecting

    Port for connecting Port Port name description Power switch Input: 5V AC, 1A 10/100/1000M Connect it to Network 10/100/1000M Connect it to PC External console Port type: RJ-45 direct connector interface Headset Port type: RJ-9 connector Handset Port type: RJ-9 connector Icon introduction Icon Description...

  • Page 10: Led Introduction

    Call mute Contact DND(Do not Disturb) In hand free mode In handset mode In headset mode Missed call Call forward LED introduction Table 1 Programmable key LEDs for BLF LED Status Description Steady green The object is in idle status Slow blinking red The object is ringing Steady red...
  • Page 11 Slow Blinking green The call is on hold/ Registration is unsuccessful The line is unapplied or idle Table 4 Programmable key LEDs for line LED Status Description Steady green The account is active Fast Blinking green There is an incoming call to the account Slow Blinking green The call is on hold Slow Blinking red...

  • Page 12: Initial Connecting And Setting

    Initial connecting and Setting Connect the phone 2.1.1 Connect to network Step 1: Connect the IP Phone to the corporate IP telephony network. Before you connect the phone to the network, please check if your network can work normally. You can do this in one of two ways, depending on how your workspace is set up. Direct network connection—by this method, you need at least one available Ethernet port in your workspace.

  • Page 13: Power Adaptor Connection

    Make sure that the power you use is comply with the parameters of power adaptor. 1. Plug power adaptor to power socket. 2. Plug power adaptor’s AC output to the AC5V port of DW-610G to start up. 3. There will be displayed black line and “initializing... wait logon...” on the screen.

  • Page 14: Network Settings

    Make sure that network is connected already before setting network of phone. DW-610G uses DHCP to get WAN IP configurations, so phone could access to network as long as there is DHCP server in it. If there is no DHCP server available, phone has to be changed WAN network setting to Static IP or PPPoE.
  • Page 15 3. Check the status, the screen shows “DHCP”， If the screen shows the IP address and gateway which were set just now, it shows that DHCP mode takes effect.

  • Page 16: Dw-610G's Basic Function

    DW-610G’s basic function Making a call 3.1.1 Call Device You can make a phone call via the following devices: 1. Pick up the handset, icon will be showed in the idle screen. 2. Press the Speaker button, icon will be showed in the idle screen.

  • Page 17: Dnd

    Press DND softkey to active DND Mode. Further incoming calls will be rejected and the display shows: icon. Press DND softkey twice to deactivate DND mode. You can find the incoming call record in the Call History. Call Forward This feature allows you to forward an incoming call to another phone number. The display showed icon.

  • Page 18: Mute

    Mute Press Mute button during the conversation, icon will be showed in the LCD. Then the called will not hear you, but you can hear the called. Press it again to get the phone to normal conversation. Call transfer 1. Blind Transfer During talk, press the key Transf, and then dial the number that you want to transfer to, and finished by "#".
  • Page 19 same time.There are four keys used as SIP line toleranted to make calls in SIP accounts.It will blink when the account registed failed. In order to convenience the enterprise the phone support multiple call answering , call hold and multi-line call.The user can answer 10 incoming call phones at most,you can choose any call through pressing the fluctuation navigation key in taiking and the other 9 calls will be in held.You also can press the fluctuation navigation key to change the call and recover the talking then last call will be held automatic.You also can define the six line keys as multi-line...

  • Page 20: Dw-610G's Advanced Function

    DW-610G’s advanced function Call pickup Call pickup is implemented by simulating pickup function of PBX. it’s that, when A calls B, B rings but no answer, at this moment, C can hook off and input an appointed prefix plus B’s number, pick up A’s call and talk with A.

  • Page 21: Click To Dial

    *3* is appointed prefix code. After making the above configuration, A can dial *3* plus B’s phone number to make the redial function. *4* is appointed prefix code. After configuration, A can dial *4* to cancel redial function. User can set prefix in random, in the case of no affecting current dialing rules. Click to dial When user A browses in an appointed Web page, user A can click to call user B via a link (this link to user B), then user A’s phone will ring, after A hooks off, the phone...

  • Page 22: Memo

    2) Use the navigation keys to highlight the options. You can read the message in the Inbox/Outbox. 3) After view the new message, you can press Reply to reply the message, and use the 123 softkey to change the Input Method, when enter the reply message, press OK, then use the navigation keys to select the line from which you want to send, then Send.

  • Page 23: Programmable Key Configuration

    4.10 Programmable Key Configuration The phone has 12 programmable keys which are able to set up to many functions per key. The following list shows the functions you can set on the programmable keys and provides a description for each function. The default configuration for each key is N/A which means the key hasn’t been set for any functions.
  • Page 24 You need setting a server number, when you have set what represent Call park. If you have a calling and you busy now, you could press the key and hear a number, then you could choose other phone and input this number. so you can directly recover call..
  • Page 25 It needs the cooperation with the Broadsoft server. The traditional BLF is that every number will need to be subscribed, so if the numbers that subscribed is so many that it will cause to obstruction. However, BLF List Key will put the numbers that needed to be subscribed in a group, and the phone use the URL of the group to subscribe and analyze the specific information of each number such as number, name, state and so on according to the notifications from the server.

  • Page 26: Dw-610G's Other Functions

    DW-610G’s other functions Auto Handdown Press Menu ->Features-> Enter->Auto Handdown-> Enter. 2. Set the Mode Enable through the navigation key, then set Time, unit is minute, then press Save. 3. When the call ends, after the time that you have set, the phone will back to the idle interface.

  • Page 27: Auto Redial

    example: Number: 1T, Dest.: 0.0.0.0, Port: 5060, Mode: SIP, Alisa: all:3333, Suffix: no suffix, Del Len: 0. Then press Save. Then press Save. 3. Input 1+number (1234) in the dial interface, you can dial out 3333. You can refer to 8.3.3.4 DIAL PEER. Auto Redial 1.

  • Page 28: Password Dial

    set. 5.11 Password Dial 1. Press Menu ->Features-> Enter->Password Dial-> Enter. 2. Enable this function, you can also set Prefix and Length. For example，you want call out 1234567 and you set Password Dial Prefix 123 and Password Length 3, then enter the dial interface and input 1234567, and then the screen will show 123***7.

  • Page 29: Dw-610G's Basic Setting

    DW-610G’s basic setting Keyboard 1. Press Menu ->Settings-> Enter->Basic Setting-> Enter->Keyboard->Enter. 2. There are four items: DSS Keys, Multiplex, Long Click, SoftKey, You can set up respectively on them. Press the key Enter to the interface, then use the navigation keys to choose the function for the key according to you want.

  • Page 30: Greeting Word

    2. You can enter the message and press Save, it will display in the phone screen when the phone start up. Language Set 1. Press Menu ->Settings-> Enter->Basic Setting-> Enter->Language Set->Enter. 2. DW-610G support two languages, you can use the navigation keys to make a choice.The default two languages are English and Chinese.

  • Page 31: Dw-610G's Advanced Settings

    DW-610G’s advanced settings Account Press Menu->Enter->Advanced settings, and then input the password to enter the interface, the default password is 123. You can set it through the web page. Then choose Account then press Enter, you can do some sip settings.

  • Page 32: Web Configuration

    Web configuration Introduction of configuration 8.1.1 Ways to configure There are three different configurations with DW-610G for different users.. Use phone keypad.   Use web browser（recommendatory way）.  Use telnet with CLI command. 8.1.2 Password Configuration There are two levels to access to phone: root level and general level. User with root level can browse and set all configuration parameters, while user with general level can set all configuration parameters except SIP (1-6) or IAX2’s that some parameters...

  • Page 33: Configuration Via Web

    After you configure the IP phone, you need click save button in config under Maintenance in the left catalog to save your configuration. Otherwise the phone will lose your modification after power off and on. Configuration via WEB 8.3.1 BASIC 8.3.1.1 Status Status Field name...
  • Page 34 8.3.1.2 Wizard Wizard Please select the proper network mode according to the network condition. DW-610G provide three different network settings: Static: If your ISP server provides you the static IP address, please select this  mode, and then finish Static Mode setting. If you don’t know about parameters of Static Mode setting, please ask your ISP for them.
  • Page 35 IP Gateway Input the Gateway address distributed to you. DNS Domain Set DNS domain postfix. When the domain which you input cannot be parsed, phone will automatically add this domain to the end of the domain which you input before and parse it again.
  • Page 36 Display detailed information that you manual config. Choose DHCP MODE，click【NEXT】can config SIP(default SIP1)simply, also can browse too. Click【BACK】can return to the last page. Like Static IP MODE。 Choose PPPoE MODE，click【NEXT】can config the PPPoE account/password and SIP(default SIP1)simply, also can browse too. Click【BACK】can return to the last page.

  • Page 37: Network

    8.3.1.4 LANGUAGE LANGUAGE SET Field name explanation Language Set the language of phone, English is default. The greeting message will display on LCD when phone is Greeting Words idle. It can support 16 chars. the default chars are VOIP PHONE. Notice: the maximal length of the greeting message is sixteen English characters and five Chinese characters 8.3.2...
  • Page 38 MAC Timestamp Shows the time of getting MAC address Please select the proper network mode according to the network condition. DW-610G provide three different network settings: Static: If your ISP server provides you the static IP address, please select this ...
  • Page 39 Subnet Mask Input the Netmask distributed to you. IP Gateway Input the Gateway address distributed to you. Set DNS domain postfix. When the domain which you DNS Domain input cannot be parsed, phone will automatically add this domain to the end of the domain which you input before and parse it again.
  • Page 40 8.3.2.2 LAN Config LAN Config Field name explanation IP Address Specify LAN static IP. Subnet Mask Specify LAN Netmask. Select the DHCP server of LAN port or not. After you DHCP Service modify the LAN IP address, phone will amend and adjust the DHCP Lease Table and save the result amended automatically according to the IP address and Netmask.
  • Page 41 In chart 1, there is a layer 2 that switches without setting VLAN. Any broadcast frame will be transmitted to the other ports except the send port. For example, a broadcast information is sent out from port 1 then transmitted to port 2,3and 4. In chart 2, red and blue indicate two different VLANs in the switch, and port 1 and port 2 belong to red VLAN, port 3 and port 4 belong to blue VLAN.
  • Page 42 QoS&VLAN Configuration LLDP Setting Enable LLDP Enable LLDP by selecting it After enabling LLDP Learn, telephone can automatically Enable Learning learn the data of DSCP, 802.1p, VLAN ID from the switch. If Function the data is different from the data of the LLDP server, telephone will change its own value as the value of the switch（Synchronous with VLAN in switch）...
  • Page 43 LAN Port VLAN ID Specify the value of the Port VLAN ID different from WAN ID, the range of the value is 0-4095 8.3.2.4 Service Port You can set the port of telnet/HTTP/RTP by this page. SERVICE PORT Field name explanation Service Port Web Server Type...
  • Page 44 2) Please REBOOT the system if you modify the HTTP or telnet port number (the new number should be greater than 1024.) 3) If you set 0 for the HTTP port, it will disable HTTP service. 8.3.2.5 DHCP SERVER DHCP SERVER Field name explanation DHCP Lease Table...
  • Page 45 DNS Server Address Set the default DNS server IP of the lease table; Click the Add button to submit and add this lease table Select name of lease table, click the Delete button will delete the selected lease table from DHCP lease table. DNS Relay Select DNS Relay, the default is enabled.
  • Page 46 TIME&DATE Field name explanation Simple Network Time Protocol (SNTP) Settings Enable SNTP Enable SNTP by selecting it Enable DHCP Time Enable DHCP Time by selecting it, then the phone will automatically synchronize the standard time. Primary Server Set SNTP Primary Server IP address. Secondary Server Set SNTP Secondary Server IP address Time Zone...

  • Page 47: Voip

    Settings Enable Enable daylight saving time Offset(minutes) Setup the variety length Month Setup start and end month Week Setup start and end week Setup start and end day Hour Setup start and end hours Minute Setup start and end minutes Manual Time Settings Notice: You need specify the above all items.
  • Page 49 SIP Config Field name explanation SIP Line Choose line to set info about SIP, there are 4 lines to choose. You can switch by 【Load】button. Basic Settings Status Shows if the phone has been registered the SIP server or not; or so, show Unapplied. Server Address Input your SIP server address.
  • Page 50 Disable Codecs/Enable Use the navigation keys to highlight the desired one in Codecs the Enable/Disable Codecs list, and press the desired to move to the other list. Advanced SIP Setting Select call forward mode, the default is Off Off：Close down calling forward Forward Type Busy：If the phone is busy, incoming calls will be forwarded to the appointed phone.
  • Page 51 Session Timeout Set the session timeout Subscribe for MWI Enable the Subscribe for MWI by selecting it, the phone will send subscribe message for MWI to the SIP Server MWI Number Specify the MWI Number; Please contact your system administrator for the connecting code. Different systems have different codes.
  • Page 52 Always CFwd Off Code Set the Always CFwd Off Code, when you choose to disable the always forward function on your phone, it will send message to the server, and the server will turn off the function immediately. Busy CFwd On Code Set the Busy CFwd On Code, when you choose to enable the busy forward function v on your phone, it will send message to the server, and the server will turn on the...
  • Page 53 to keep alive. If the type is UDP, the phone will send UDP message to server to keep alive every NAT Keep Alive Period(s). Keep Alive Interval Set examining interval of the server, default is 60 seconds User Agent Set the user agent if have, the default is VoIP Phone 1.0 Select DTMF sent mode, there are three modes: DTMF_RELAY ...
  • Page 54 Answer With A Single Enable/Disable the function when call is incoming, Codec phone replies SIP message with just one codec which phone supports. Auto TCP Set to use automatically TCP protocol to guarantee usability of transport as message is above 1300 byte Enable Strict Proxy Support the special SIP server-when phone receives the packets sent from server，...
  • Page 55 Notice: the deployment will become effective in all sip lines. 8.3.3.2 IAX2 Config IAX2 Config Field name explanation Status Shows if the phone has been registered the IAX2 server or not. Server Address Input your IAX2 server address. Server Port Set your IAX2 server port, the default is 4569.
  • Page 56 Voice Mail Number Specify the voice mail’s number. Voice Mail Text Specify the voice mail’s name. Set echo test number. If IAX2 server supports echo test, and Echo Test Number echo test number is non- numeric, system could set an echo test number to replace the echo test text.
  • Page 57 STUN Field name explanation Simple Traversal of UDP through NATs (STUN) Settings STUN NAT Traversal Shows STUN NAT Transverse estimation, true means STUN can penetrate NAT, while False means not. Server Address Set your SIP STUN Server IP address Server Port Set your SIP STUN Server Port Set STUN blinding period(s).
  • Page 58 Choose line to set info about SIP, There are 6lines to choose. You can switch by 【Load】 button. Use STUN Enable/Disable SIP STUN. Notice: SIP STUN is used to realize SIP penetration to NAT. If your phone configures STUN Server IP and Port (default is 3478), and enable SIP Stun, you can use the ordinary SIP Server to realize penetration to NAT.
  • Page 59 separated by commas, or a list of digits. If user makes the above configuration, after user dials 11 digit numbers started with from 132 to 139, the phone will send out 0 plus the dialed numbers automatically. Use this phone you can realize dialing out via different lines without switch in web interface.
  • Page 60 1) Add: xxx, it means that you need dial xxx in front of phone number, which will reduce dialing number length. 2) All: xxx, it means that xxx will replace some phone number. 3) Del: It means that phone will delete the number with length appointed. 4) Rep: It means that phone will replace the number with length and number appointed.

  • Page 61: Phone

    The phone will automatically send out alias When you dial number adding your dialed “8309“, the SIP1 number, if your dialed server will receive number starts with your set “07558309” phone number. You need set Phone Number, Alias and Delete Length.
  • Page 62 DSP Configuration Field name explanation First Codec The first preferential DSP codec:G.711A/U,G.722,G.723,G.729,G.726-32 Second Codec The second preferential DSP codec: G.711A/U,G.722,G.723,G.729,G.726-32,NONE Third Codec The third preferential DSP codec: G.711A/U,G.722,G.723,G.729,G.726-32 ,NONE Fourth Codec The forth preferential DSP codec: G.711A/U,G.722,G.723,G.729,G.726-32 ,NONE Fifth Codec The fifth preferential DSP codec: G.711A/U,G.722,G.723,G.729,G.726-32,NONE Sixth codec...
  • Page 63 Tone Standard Select Tone Standard. EnableVAD Select it or not to enable or disable VAD. If enable VAD, G729 Payload length could not be set over 20ms. DTMF Payload Type Set DTMF Payload Type. 8.3.4.2 FEATURE In this web page, you can configure Call Transfer, Call Waiting, 3 Ways Call, Black List, white list Limit List and so on.
  • Page 64 FEATURE Field name explanation Do Not Select DND, the phone will reject any incoming call, the callers will Disturb be reminded by busy, but any outgoing call from the phone will work well. Ban Outgoing If you select Ban Outgoing to enable it, and you cannot dial out any number.
  • Page 65 Auto Redial Specify the Auto Redial interval, interval Auto Redial Specify the Auto Redial interval Times Enable the function and put on the headset, when there has a Auto Headset incoming call ,you can press the answer key or line key to answer the call through the headset ,and it’s the same if enable auto answer function.
  • Page 66 Enable Silent Enable Silent Mode by selecting it, the phone light will red blink to Mode remind that there is a missed call instead of playing ring tone Turn Off Enable Turn Off Power Light by selecting it Power Light Emergency Specify the Emergency Call Number.
  • Page 67 Settings FileName is name of xml that contains the action message ） Block Out Settings Set Add/Delete Limit List. Please input the prefix of those phone numbers which you forbid the phone to dial out. For example, if you want to forbid those phones of 001 as prefix to be dialed out, you need input 001 in the blank of limit list, and then you cannot dial Block out out any phone number whose prefix is 001.
  • Page 68 DIAL PLAN Configuration Field name explanation Basic Setting Press "#" to Send Set Enable/Disable the phone ended with “#” dial. Dial Fixed Length Specify the Fixed Length of phone ending with. Send after （3-30） Set the timeout of the last dial digit. The call will be sent seconds after timeout.
  • Page 69 length. n is mandatory and can have a value of 0 to 9 seconds. Tn must be the last 2 characters of a dial plan. If Tn is not specified it is assumed to be T0 by default on all dial plans. Cause extensions 1000-8999 to be dialed immediately Cause 8 digit numbers started with 9 to be dialed immediately Cause 911 to be dialed immediately after it is entered.
  • Page 70 CONTACT Field name explanation Phonebook Table Name Shows the name corresponding to the phone number Number Shows the phone number Ring Type Shows the ring type of the incoming call. Group Shows the group of the contact Notice: the maximum capability of the phonebook is 500 items, you can select many or a contact to add to group and add to blacklist, and delete many or a contact, and delete all contacts.
  • Page 71 model Export CSV Click export xml button to export phonebook file of csv model Export VCF Click export xml button to export phonebook file of vcf model Blacklist Settings Type Select the blacklist type, you can select number or prefix of number Value Input number or prefix of number Line...
  • Page 72 Setting Phonebook Name Custom the phonebook name displayed on the phone Server URL Specify the server url of the remote phonebook Sip Line Specify the sip line for the remote phonebook Authentication Specify the authentication mode for remote phonebook Username/password Input the authentication username and password remote book support the modes as HTTP ,FTP ,TFTP ,LDAP （Note:...

  • Page 73: Function Key

    8.3.5 Function Key 8.3.5.1 Function Key Field name explanation Contrast Set contrast of screen Enable Backlight Set enable/disable backlight Line Key Settings Line: select Auto, SIP1, SIP2, SIP3, SIP4, or IAX2 in function key type. After you set it, you pick up handset or hands-free, press this function key, and then you...
  • Page 74 can use the corresponding SIP line. Function Key Settings Show the function key's serial number Type Memory Key: settings can be stored in key storage for each number, the standby or off-hook, select the function keys on the keyboard can call this number. Line, set the dial mode (Auto, SIP1, SIP2, SIP3, SIP4, IAX2).Key Key Event functions, monitor state.
  • Page 75 8.3.5.2 EXT KEY EXT KEY has the same usage with the Function key. “In” port connects the phone, “Out” port connects the next one, if there is only, you don’t need for power supply, if there are more than one, you need supply 5V power for the first one, and use RJ-45 direct connector.

  • Page 76: Maintenance

    8.3.5.3 SOFTKEY You can configure different functions in different screens for every softkey. 8.3.6 Maintenance 8.3.6.1 Auto Provision...
  • Page 77 Supports PnP and DHCP and Phone Flash to obtain the parameters. The PnP and DHCP and Phone Flash are all deployed, endpoint will go by the following process to try to obtain the server address and other parameters, when it boots up: DHCP option ...
  • Page 78 Config Encrypt Key Input the Encrypt Key, if the configuration file is encrypted. Common Config Input the Common Encrypt Key, if the Common Encrypt Key Configuration file is encrypted Save Autoprovision Save the username and password authentication message Information of http/https/ftp and input ID message in the phone until the URL in the server changes DHCP Option Setting DHCP Option Setting...
  • Page 79 Enable TR069 Enable TR069 by selecting it ACS Server Type Specify the ACS Server Type ACS Server URL Specify the ACS Server URL ACS User Specify ACS User ACS Password Specify ACS Password It will check every 6 minutes Periodix Interval TR069 Auto Login Enable TR069 Auto Login by selecting it "Inform"...
  • Page 80 Syslog Configuration Field name explanation Syslog Setting Server Address Set Syslog server IP address. Server Port Set Syslog server port. MGR Log Level Set the level of MGR log. SIP Log Level Set the level of SIP log. IAX2 Log Level Set the level of IAX2 log.
  • Page 81 configurations and restore factory default; if you login as Guest, the phone will reset all configurations except for VoIP accounts (SIP1-4 and IAX2) and version number. 8.3.6.4 Update You can update your configuration with your config file in this web page. Update Field name explanation...
  • Page 82 can download a config file just keep with SIP module. After reboot, other modules of system still use previous setting and are not lost. Action type that system want to execute： 1. Application update: download system update file Type 2. Config file export: Upload the config file to FTP/TFTP server, name and save it.
  • Page 83 Access Configuration Field name explanation Keyboard Password Set the password for entering the setting menu of the phone by the phone‘s key board. The password is digit. This table shows the current user existed. User Set account user name. User Level Set user level, Root user has the right to modify configuration, General can only read.

  • Page 84: Reboot

    Reboot If you modified some configurations which need the phone’s reboot to be effective, you need click the Reboot, then the phone will reboot immediately. Notice: Before reboot, you need confirm that you have saved all configurations. 8.4.1 Security 8.4.1.1 WEB Filter WEB Filter User could make some device own IP, which is pre-specified, access to the MMI of the phone to config and manage the phone.
  • Page 85 8.4.1.2 Firewall Firewall Configuration In this web interface, you can set up firewall to prevent unauthorized Internet users from accessing private networks connected to the Internet (input rule), or prevent unauthorized private network devices from accessing the Internet (output rule). Firewall supports two types of rules: input access rule and output access rule.
  • Page 86 Port Range Set the filter Port range Src Address Set source address. It can be single IP address, network address, complete address 0.0.0.0, or network address similar to *.*.*.0 Des Address Set the destination address. It can be IP address, network address, complete address 0.0.0.0, or network address similar to *.*.*.* Set the source address’...
  • Page 87 DMZ config： In order to make some intranet equipments support better service for extranet, and make internal network security more effectively, these equipments open to extranet need be separated from the other equipments not open to extranet by the corresponding isolation method according to different demands. We can provide the different security level protection in terms of the different resources by building a DMZ region which can provide the network level protection for the equipments environment, reduce the risk which is caused by providing service to distrust...
  • Page 88 NAT Configuration Field name explanation IPSec ALG It is an encryption technology. Select it to enable IPSec ALG, the default is enable FTP is a service of connection layer which can transform FTP ALG intranet IP into extranet IP when intranet IP is sending out packet.
  • Page 89 Transfer Type Select the NAT mapping protocol style, TCP or UDP Inside IP Set the IP address of device which is connected to LAN interface to do NAT mapping. Inside Port Set the LAN port of the NAT mapping Outside Port Set the WAN port of the NAT mapping Notice: After finish setting, click the Add button to add new mapping table;...
  • Page 90 VPN Configuration Field name explanation VPN IP Shows the current VPN IP address Select L2TP. You can choose only one for current state. After you select it, you’d better save configuration and reboot your phone. Enable VPN Select it or not to enable or disable VPN； VPN Server Addr Set VPN L2TP Server IP address VPN User Name...

  • Page 91: Logout

    Delete button to update SIP TLS File Show SIP TLS authentication certification file HTTPS File Show HTTPS authentication certification file Open VPN Files Show Open VPN File authentication certification file 8.4.2 Logout Click Logout，and you will exit web page. If you want to enter it next time, you need input user name and password again.

  • Page 92: Appendix

    Appendix Specification 9.1.1 Hardware Item DW-610G(P) Adapter Input: 100-240V (Input / Output) Output: 5V 1A port 10/100/1000Base- T RJ-45 1 PORT 10/100/1000Base- T RJ-45 1 PORT Power Consumption Idle: 2.5W/Active: 2.8W LCD Size 128x96 53.5 x 70mm Operation 0～40℃ Temperature Relative Humidity 10～65%...

  • Page 93: Network Features

    SIP application: SIP Call forward/transfer （ blind/attended） /hold/waiting/3 way  talking/SMS/pickup /join call /redial /unredial/multi line/intercom/BLF/presence/push to talk/auto redial/call return Call control features: Flexible dial map, hotline, empty calling No. reject  service, black list for reject authenticated call, white list, limit call, no disturb, caller ID, CLIR(reject the anonymous call), CLIP(make a call with anonymous), Dial without register.

  • Page 94: Maintenance And Management

    QoS with DiffServ  Network tools in telnet server: including ping, trace route, telnet client  9.1.4 Maintenance and management Upgrade firmware through POST mode  Web ,telnet and keypad management  Management with different account right  LCD and WEB configuration can be modified into requested language, and ...

Table of Contents