Icom IC-F9011 User Manual page 27

SCAN A KEY "SCNA"
For Simple/10-key models
➥Push to start and cancel scanning operation.
When Power ON Scan function is activated, push
to pause the scanning operation. The paused
scan resumes after the specified time period has
passed.
➥Push and hold this key for 1 sec to indicate the
scan list, then push [CH Up] or [CH Down] to select
the desired list. (Available depending on the
pre-set value.)
For Non-display model
Push to start and cancel scanning operation.
•When Power ON Scan function is activated, push to
pause the scanning operation. And the paused pause the scanning operation And the paused
scan resumes after the specified time period has
passed.
•LED indicator blinks green slowly while scanning.
SCAN B KEY "SCNB"
For Simple/10-key models
➥ Push to start and cancel scanning operation.
The scan restarts after the specified time period The scan restarts after the specified time period
has passed when the scan (started with this key )
is cancelled by this key.
➥Push and hold this key for 1 sec to display the
scan list, push [CH Up] or [CH Down] to select
the desired list.
For Non-display model
Push to start and cancel scanning operation.
•The scan restarts after the specified time period
has passed when the scan (started with this key) is
cancelled by this key operation.
•LED indicator blinks green slowly while scanning.
TALK AROUND KEY "TA"
(Conventional operation only) ( p
The talk around function equalizes the transmit
frequency to the receive frequency for transceiver-to-
transceiver communication.
For Simple/10-key models
Push to turn the talk around function ON and OFF.
For Non-display model For Non-display model
➥Push and hold for 1 sec to turn the talk around
function ON.
➥When the talk around function is ON, push to turn
the function OFF.
Functions Programmable to Keys
y
y)
PRIO A REWRITE AND PRIO B REWRITE KEYS
"PRAR""PRBR"
For Simple/10-key models
➥Push to select Priority A or Priority B channel.
➥Push and hold [Prio A (Rewrite)] or [Prio B
(Rewrite)] for 1 sec to rewrite the operating
channel as the Priority A or Priority B channel.
OPT OUT KEYS "OP1""OP2""OP3"
For Simple/10-key models
Push to control the output signal level from the
optional unit connector.
For Non-Display model
➥Push and hold for 1 sec to control the output
signal level from the optional unit connector. signal level from the optional unit connector
➥When this key function is activated, push to
deactivate the function.
◇For Simple/10-key models only
Following key functions cannot be programmed to
Non-Display model.
CH UP AND DOWN KEYS "UP""DOWN" CH UP AND DOWN KEYS "UP""DOWN"
➥Push to select an operating channel. When [Rotary
selector] selection mode is "operating channel,"
this function is not available.
➥Push to select a scan group after pushing and
holding [Scan A Start/Stop]/[Scan B Start/Stop].
ZONE KEY "ZONE"
Push this key, then push [CH Up] or [CH Down] to
select the desired zone.
When [Rotary selector] selects "operating zone",
push this key to switch the range of selectable
zones.
▒ What is "zone" ? --- Selected channels are assigned
▒ to a zone according to how they are to be used in a ▒ to a zone according to how they are to be used in a
▒ group. For example, 'Staff A' and 'Staff B' are
▒ assigned into a "Business" zone, and 'John' and
▒ 'Cindy' are assigned into a "Private"zone.
USER SET MODE KEY "SET"
➥Push and hold for 1 sec to enter user set mode.
• In the user set mode, push this key to
select an item that is enabled by your dealer, select an item that is enabled by your dealer
and change the value or condition by pushing
[CH Up] or [CH Down].
➥Push and hold this key again for 1 sec to exit user
set mode.
27