Table of Contents
Advertisement
List of Functions
This section describes the overview of each function to be set and set values that can be registered in user types.
• About default "HOST" function
You can operate this by the setting value specified in RIP software.
When you set to other than "HOST", it operates by that setting value, not by the instruction from RIP software.
Depending on RIP software, there are some functions that cannot be instructed by software. In such a
case, it operates by the setting value of "When no instruction from RIP exists".
• For the specifying method with the RIP software, refer to the operation manual of the RIP software.
Function name
FEED COMP. (
P.2-34)
DROP. POS CORRECT
(
P.2-36)
MEDIA
HEATER
HEATER
(
P.2-28)
INK
HEATER
LOGICAL SEEK(
P.3-5)
INK LAYERS (
P.3-16)
LEFT
MARGIN
(
P.3-6)
RIGHT
HOST
UV MODE
(
P.3-16)
MANUAL
REFRESH (
)
P.3-16
VACUUM (
P.3-16)
FEED SPEED (
P.3-16)
PRINT SPEED
MAPS1
ADJUST
MAPS
AUTO
(
P.3-9)
MAPS2
MANUAL
OFF, PAGE,
LENGTH, TIME
PAGE
AUTO
CLEANING
LENGTH
(
P.3-14)
TIME
3-2
Set value
-9999 ~ 0 ~ 9999
-40.0 ~ 0 ~ 40.0
OFF/ 20 ~ 60°C
PRE
(OFF/ 68 ~ 140°F)
OFF/ 20 ~ 60°C
PRINT
(OFF/ 68 ~ 140°F)
OFF/ 20 ~ 70°C
POST
(OFF/ 68 ~ 158°F)
Standby
Switcho
NONE, 0 to 60min
verTIM
HOST / ON / OFF
HOST /1 ~ 9
HOST / -10 ~ 85mm
(1mm unit)
HOST / -10 ~ 85mm
(1mm unit)
-50 ～ +50％
Lv.1 ～ 10
HOST / Lv.0 (Refresh
interval long) ~ 3 (Refresh
interval short)
HOST / STANDARD /
STRONG
HOST / 10 ~ 200%
OFF/MAPS1/MAPS2
-50 to +50%
PATTERN(1 to 5)/
Smoothing level (AUTO/
5 to 100%)
INTERVAL 1 to 1000 page
TYPE
NORMAL / SOFT / HARD
INTERVAL 0.1 to100.0m
TYPE
NORMAL / SOFT / HARD
INTERVAL 10 to 120 min
TYPE
NORMAL / SOFT / HARD
When no instruction
Default
from RIP exists
0
0
OFF
OFF
OFF
2min
ON
HOST
1
HOST
0 mm
HOST
0 mm
HOST
0％
Lv.10
Lv.3
HOST
STANDARD
HOST
*2
100%
HOST
MAPS2
0%
OFF
1 page
SOFT
0.5m
SOFT
10 min
SOFT
Outline
*1
Used to print a pattern for
correcting a media-feeding rate
and correct it.
Used to adjust the dot position in
go and return printing.
Sets heater conditions.
Sets the movement time until the
head heater and ink heater
standby status.
Sets the scan movable area
during printing.
Sets the number of layers in
which ink is to be applied.
Sets a non-printing area along
the right and left edges of the
media.
Sets and adjusts the intensity of
the UV lamp.
Refreshes the print heads
during printing.
Sets the absorbability of the
media.
Changes
the
media
speed in printing.
Perform setting to reduce
stripes between passes.
Sets
the
automatic
operation for the head performed
before printing or during printing.
feeding
cleaning
Advertisement
Table of Contents
