Honeywell MX9 User Manual
  1. Manuals
  2. Brands
  3. Honeywell Manuals
  4. Handhelds
  5. MX9
  6. User manual
Honeywell MX9 User Manual

Honeywell MX9 User Manual

With microsoft windows mobile 6.5
Hide thumbs Also See for MX9:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Reference Manual
MX9 Mobile Computer
with Microsoft® Windows® Mobile 6.5
User's Guide

Advertisement

Table of Contents
loading

Related Manuals for Honeywell MX9

Summary of Contents for Honeywell MX9

  • Page 1 MX9 Mobile Computer with Microsoft® Windows® Mobile 6.5 User’s Guide...
  • Page 2 Disclaimer Honeywell International Inc. (“HII”) reserves the right to make changes in specifications and other information contained in this document without prior notice, and the reader should in all cases consult HII to determine whether any such changes have been made.

  • Page 3: Table Of Contents

    Inserting or Replacing the Battery Pack..................... 2-7 Insert/Replace Battery ......................... 2-7 Remove Battery ........................... 2-8 Insert Battery in HazLoc MX9 ...................... 2-8 Remove Battery from HazLoc MX9 ..................... 2-8 Charging/Recharging the Main Battery ....................2-8 LEDs, Backlights and Indicators ......................2-9 Status LEDs..........................
  • Page 4 Attaching the Hand Strap .........................2-18 Attaching the Trigger Handle ......................2-19 Adjusting the Headset / Microphone and Securing the Cable ............2-20 Connecting Cables to the MX9 ......................2-21 Connecting the USB Host and Power Cable................2-21 Connecting the USB Client and Power Cable................2-21 Connecting the Serial and Power Cable ..................2-22...
  • Page 5 Integrated Bar Code Decoders ....................3-6 Tethered Bar Code Decoders ......................3-6 Bluetooth Client Bar Code Decoders ...................3-6 GPS Module ............................3-6 Chapter 4 - Power Modes and Batteries Power Modes............................4-1 On Mode ............................4-1 Suspend Mode ..........................4-1 Off Mode ............................4-1 TSuspend.............................4-1 Suspend Primary Wake up Events ..................4-2 Batteries .............................4-3 Checking Battery Status.......................4-3 Main Battery Pack ........................4-3...
  • Page 6 Status Popup..........................5-6 HSMConnect..........................5-6 GrabTime .............................5-6 Synchronize with a local time server ..................5-6 Enhanced Launch ........................5-6 MX9 OS Upgrade ..........................5-7 Introduction ..........................5-7 OS and Language Options......................5-7 Preparation...........................5-7 Accessing the SD Card Slot......................5-7 Procedure ..........................5-8 Battery State and OS Upgrade ....................5-8 Upgrade Help ..........................5-8 Start Menu Options..........................5-8...
  • Page 7 Battery Power ........................5-33 External Power ........................5-34 Certificates ..........................5-35 Personal ..........................5-35 Intermediate.........................5-36 Root .............................5-37 Encryption ..........................5-38 External GPS ..........................5-39 Programs ..........................5-39 Hardware ..........................5-40 Access ..........................5-40 License Manager........................5-41 Managed Programs........................5-42 Memory ............................5-43 Main .............................5-43 Storage Card ........................5-43 Mixer ............................5-44 Mixer Panels ........................5-44 MX9WM Options ........................5-45 Communication........................5-45 Misc.
  • Page 8 Explore ............................5-85 Backup Data Files using ActiveSync..................5-85 Reset and Loss of Host Re-connection..................5-85 ActiveSync Help .........................5-86 Configuring the MX9 with HSM Connect (or LXEConnect)............5-86 Install HSM Connect ......................5-87 Using HSM Connect ......................5-87 Chapter 6 - AppLock (Application Locking) Introduction ............................6-1 Setup a New Device ...........................6-1...
  • Page 9 About ..............................7-11 Easy Pairing and Auto-Reconnect....................7-12 Bluetooth Indicators..........................7-12 Bluetooth Bar Code Reader Setup ....................7-12 Introduction ..........................7-12 MX9 with Label...........................7-13 MX9 without Label........................7-13 Bluetooth Reader Beep and LED Indications ...................7-13 Bluetooth Printer Setup ........................7-14 Chapter 8 - Data Collection Wedge Introduction ............................8-1 Return to Factory Default Settings .....................8-1...
  • Page 10 Symbology Settings ........................8-10 Processing Order ........................8-11 Strip Leading/Trailing Control.....................8-12 Barcode Data Match List......................8-13 Add Prefix/Suffix Control ......................8-14 Symbologies..........................8-15 AIM Symbologies.........................8-15 HHP Symbologies .......................8-16 Advanced Button (Hand Held Products Imager Only) ............8-16 Ctrl Char Mapping .......................8-31 Custom Identifiers........................8-32 Control Code Replacement Examples.................8-33 Bar Code Processing Examples ..................8-34 Length Based Bar Code Stripping....................8-35 Processing Tab..........................8-37...
  • Page 11 Chapter 10 - Enabler Installation and Configuration Introduction ............................10-1 Installation ............................10-1 Installing the Enabler ........................10-1 Enabler Uninstall Process ........................10-2 Stop the Enabler Service........................10-2 Update Monitoring Overview ......................10-2 Mobile Device Wireless and Network Settings .................10-2 Preparing a Device for Remote Management ..................10-3 User Interface ...........................10-4 Enabler Configuration ........................10-4 File Menu Options ........................10-5...
  • Page 12 Global Tab..........................11-14 Custom Parameter Option ....................11-15 Global Parameters......................11-15 Sign-On vs. Stored Credentials ......................11-19 Using Stored Credentials ......................11-19 Using a Sign On Screen......................11-19 Windows Certificate Store vs. Certs Path..................11-21 User Certificates........................11-21 Root CA Certificates.........................11-21 Using the Certs Path ......................11-21 Using the Windows Certificate Store .................11-21 Configuring Profiles ........................11-23 No Security..........................11-23 WEP ............................11-24...
  • Page 13 Connecting a USB Host and USB Client Cable..............14-7 Cradle LEDs..........................14-7 Docked LED ........................14-7 Spare Battery LED.......................14-8 MX9 System Status LED Status when Docked ..............14-8 Docking and Undocking the MX9....................14-8 Dock the MX9 ........................14-8 Undock the MX9 ........................14-8 Inserting / Removing a Spare Battery from the Desktop Cradle ..........14-8 Inserting a Spare Battery .....................14-9...
  • Page 14 Vehicle Cradle Strain Relief Cable Clamp ................14-23 Vehicle Cradle LED........................14-24 Docking the MX9 in a Vehicle Mounted Cradle................14-24 Removing the MX9 from the Mounted Vehicle Cradle .............14-25 Powered Vehicle Cradle Help ....................14-25 Chapter 15 - Technical Specifications MX9 Specifications ...........................15-1 MX9 Dimensions and Weight.

  • Page 15: Chapter 1 - Mx9 Agency Compliance

    • Do not stare directly into the laser beam. • Do not remove the laser caution labels from the MX9. • Do not connect the laser bar code aperture to any other device. The laser bar code aperture is certified for use with the MX9 only.

  • Page 16: Canadian Compliance

    “Something About Interference.” This is available at FCC local regional offices. Honeywell is not responsible for any radio or television interference caused by unauthorized modifications of this equipment or the substitution or attachment of connecting cables and equipment other than those specified by Honeywell. The correction is the responsibility of the user.
  • Page 17 Nijverheidsweg 9-13 5627 BT Eindhoven The Netherlands Honeywell shall not be liable for use of our product with equipment (i.e., power supplies, personal computers, etc.) that is not CE marked and does not comply with the Low Voltage Directive. RF Notices This device can contain transmitter Module(s) FCC ID: DDZLXE4830P, KDZBT001, E09HHSR3.

  • Page 18: Vehicle Power Supply Connection Safety Statement

    5 inches (12.7 cm) of the battery positive (+) terminal. Brazil Restrictions Bluetooth and GSM technology are not available in Brazil. In Brazil the MX9 is not available with the MX9 AC/DC power adapter and MX9 Desktop cradle. 1 - 4...

  • Page 19: Chapter 2 - Getting Started

    The keypad is available in a 62-key or 38-key configuration. The 62-key keypad is also available in an IBM 5250 configuration. Bar code reader options are: an imager or laser scanner integrated in the MX9, or a handheld scanner tethered to the port at the base of the MX9, Bluetooth mobile bar code imagers and scanners, or the Bluetooth Ring Scanner module.

  • Page 20: Software Setup

    • Place the MX9 in a powered desktop or vehicle mounted cradle. 3. Press the Power key. Software Setup Hardware setup should be completed before starting software setup. 1. Calibrate touch display. 2. Set Date and Time Zone. 3. Set Power Timers.

  • Page 21: Components

    2. Touch screen 3. Speaker 4. Scan buttons 5. Enter key 6. Scanner status LED 7. Power key The above list is the same on the 38 key MX9. Special keys are listed on the following pages. 2 - 3...

  • Page 22: 62 Key Keypad

    62 Key Keypad 1. Function Keys 2. Backspace [BS] key and Space [SPC] key 3. Escape [ESC] key 4. Power key 5. Tab key 6. Alt key 7. Control [CTL] key 8. Orange key 9. Blue key 10. Shift [SHFT] key ENTER 11.

  • Page 23: Top

    38 Key Keypad 1. Diamond 1 key 2. Function keys 3. Tab | Space | Backspace keys 4. Diamond 2 key 5. Orange key 6. Escape [ESC] key 7. Power key Caps BKSP 8. Alpha key 9. Control [CTRL] key ENTER 10.

  • Page 24: Back - Battery Bay

    Back - Battery Bay 1. Battery Charging Terminals 2. Battery Bay 3. Battery Bay Access Tab Trigger Handle 1. Trigger 2. Tether attach point Stylus storage bay in trigger handle base 2 - 6...

  • Page 25: Hand Strap

    When the MX9 is locked, the Start screen displays Unlock at the lower part of the screen. • If there is no password or PIN set, tap Unlock on the next screen to unlock the MX9. The MX9 is returned to normal operation.

  • Page 26: Remove Battery

    Hazardous Locations. New batteries must be fully charged prior to use. The main battery can be recharged in an AC powered Battery Charger after the battery has been removed from the MX9 or its packing material when new. The main battery while in the MX9 can be recharged using several different methods.

  • Page 27: Leds, Backlights And Indicators

    Toggle Vibrate Indicator The MX9 vibration motor is activated when a scan is completed successfully (good scan vibration) or with a failure (scan key released before good scan, timeout, or rejected because of Data Options configuration). The vibrations can be detected under the hand strap or through the trigger handle.

  • Page 28: Tapping The Touch Screen With A Stylus

    Adjusting the Display Backlight Timer The backlight settings use the Honeywell set of default timeouts. When the backlight timer expires, the display backlight is dimmed, not turned off. When both check boxes are unchecked, the backlight never turns off (or dims). Default values are 30 seconds for Battery, 1 minute for External and both the check boxes are enabled.

  • Page 29: Adjusting The Keypad Backlight

    Setting Date and Time Zone Note: The first time the MX9 is powered on, or the device returns from a clean boot, the operating system may reset the Time to the factory default value.

  • Page 30: Setting Speaker Volume

    Setting Speaker Volume The speaker is located on the front of the MX9 between the Scan keys and underneath the LEDs. Speaker volume can be adjusted to a comfortable level for the listener by using the keypad or by changing parameters in a control panel.

  • Page 31: Body Worn Accessories

    Protect the Touch Screen when using a Holster / Carrycase . Holster without Handle The MX9 is inserted upside-down in the holster with the touch screen facing the belt connecting the holster to the body. Holster with Handle The MX9 is inserted upside-down in the holster with the touch screen facing the belt connecting the holster to the body.

  • Page 32: Using The Input Panel / Virtual Keyboard

    • The system administrator has also assigned a Computer Friendly Name using EZPair control panel for the MX9. To connect Bluetooth devices, the MX9 should be as close as possible and in direct line of sight (distances up to 32.8 feet or 10 meters) with the targeted Bluetooth device during the discovery and pairing process.

  • Page 33: Setting Terminal Emulation Parameters

    • The LED blinks slowly (Bluetooth LED is on for one second, off for five seconds) when it is idle. • The LED blinks quickly (Bluetooth LED is on for 1/4 second, off for 2 seconds when the MX9 is discovering other Bluetooth devices.

  • Page 34: Using The Touch Screen

    (page 16-1) if you need help when installing or removing a SIM card. The expansion slots in the MX9 are accessible via the hatch. The hatch can be opened using a standard size screwdriver. When the hatch is opened, the MX9 automatically shuts down. It is good practice to save any changes then perform an orderly shutdown to preserve RAM contents before opening the hatch.
  • Page 35 When the hatch is being closed, carefully move cables and wires back into the cavity before securing the hatch. Before securing the hatch completely, examine the seam between the front and back half of the MX9. If the gasket is off-center, loosen the screws a little, adjust the gasket and re-tighten the screws.

  • Page 36: Attaching The Hand Strap

    3. Insert the screws (supplied) into each of the four holes and fasten the base securely. 4. Slide the hand strap bottom clip pins into the slots at the base of the MX9 and pull the strap towards the top of the MX9 until the top clip slips into the groove.

  • Page 37: Attaching The Trigger Handle

    Equipment needed: Torque wrench capable of torquing to 3±1 in/lb (.34±.11 N/m). Either the trigger handle or the hand strap is attached, not both. Honeywell recommends that, in the absence of a trigger handle, the hand strap be used at all times.

  • Page 38: Adjusting The Headset / Microphone And Securing The Cable

    The headset consists of an earpiece, a microphone, a clothing clip and a cable. The headset attaches to the audio cable end of the voice cable which attaches to the MX9. Align the audio connector and the headset quick connect cable end. Firmly push the cable ends together until they click and lock in place.

  • Page 39: Connecting Cables To The Mx9

    1. Holding the cable I/O connector (1), pinch the catch release buttons in until the catches are open. Connect the cable to the MX9 I/O port by matching the shape of the I/O connector on the cable with the shape of the I/O connector at the base of the MX9.

  • Page 40: Connecting The Serial And Power Cable

    1. Holding the cable I/O connector (1), squeeze the catch release buttons in until the catches are open. Connect the cable to the MX9 I/O port by matching the shape of the I/O connector on the cable with the shape of the I/O connector at the base of the MX9.

  • Page 41: Replacing The Cla Fuse

    Equipment needed: 5A fuse of the same size and amperage. 1. Remove the CLA from the cigarette lighter outlet on the vehicle. 2. Disconnect the cable from the MX9. 3. Unscrew the tip of the adapter end. 4. Replace the blown fuse with a fuse of the same rating and size.

  • Page 42: Startup Help

    New batteries must be fully charged prior to first use. Li-Ion batteries (like all batteries) gradually lose their capacity over time (in a linear fashion) and never just stop working. This is important to remember – the MX9 is always ‘on’ even when in the Suspend state and draws battery power at all times.

  • Page 43: Chapter 3 - Hardware Configuration

    WEP, WPA and LEAP are supported. Central Processing Unit The CPU is a 806 MHz Marvell PXA-320 CPU. The OS image is stored in on-board flash memory. The MX9 supports the following I/O components of the core logic: •...

  • Page 44: Input/Output Connector

    • Ethernet (only accessible when MX9 is secured in a cradle docking bay) The MX9 cables are designed to be securely connected to this port. This port is also used to connect the MX9 to the docking bay connector in cradles.

  • Page 45: Keypads

    SHFT SHIFT 62-Key Keypad 38-Key Keypad The MX9 keypad is either a 62-key full alphanumeric keypad or 38-key numeric-alpha. The 62 key keypad has an ANSI or a 5250 overlay. KeyMaps (page 12-1) are available for all keypads. Note: The keypad backlight default setting is to follow the display backlight setting until it is changed by the user.

  • Page 46: Power Key Functions

    Suspend mode Status LEDs Several LEDs are located on the front of the MX9 above the integrated speaker. They are: • System Status (SYS) LED indicates power management status. • Battery Charging Status (BATT) LED indicates main battery charging status.

  • Page 47: Scanner Status Led

    (writing to scan engine). While the changes are being saved, the scanner/imager is inoperable. • The MX9 Scan Status LED does not illuminate when the Scan button is pressed on a scanner cabled to the MX9 or cabled to an MX9 cradle communication port.

  • Page 48: Scanners And Imagers

    A scan aperture heater is implemented for low temperature environments. Tethered Bar Code Decoders The external serial port at the base of the MX9 is used to connect (via serial tether) tethered laser scanners as needed. Bluetooth Client Bar Code Decoders The Bluetooth Module in the MX9 can accept data from paired Bluetooth bar code readers.

  • Page 49: Chapter 4 - Power Modes And Batteries

    • the display backlight and keypad backlight are on until the Backlight timer expires The MX9 After a new MX9 has been received, a charged main battery inserted, and the Power key tapped, the MX9 is always On until both batteries are drained completely of power.

  • Page 50: Suspend Primary Wake Up Events

    The MX9 will only resume from a suspended state if an interrupt occurs and the CPU has been programmed to wake when an interrupt occurs. An interrupt from any listed device transitions the OS back to the On state. Suspend Primary Wake up Events Wake up Events - all configurable via command line utility: •...

  • Page 51: Batteries

    4 hours. The MX9 can be Off, in use or in Suspend Mode while the battery is recharging. Note: New main battery packs must be charged prior to use. This process takes up to four hours in an MX9 Battery Charger and six hours when the MX9 is connected to external power.

  • Page 52: Handling Batteries Safely

    Car Power Adapter The MX9 Car Power Adapter is a self-contained unit. The cable has one and a half feet of coiled cord and one and a half feet of straight cord. The coiled portion is on the end of the adapter. An LED on the adapter illuminates when the car power adapter is receiving vehicle input power.
  • Page 53 CLA plug that uses center positive (+12V) and sleeve ground. A replaceable fuse is provided on the input side. The other end of the three foot cable connects to the MX9 36-pin I/O port. It has a security latch for stability when the MX9 is connected to the Car Power Adapter cable.
  • Page 54 4 - 6...

  • Page 55: Chapter 5 - Software Configuration

    The files are stored in folders in the mobile device. This section lists the contents of the folders and the general function of the files. Files installed in each MX9 are specific to the intended function of the MX9.

  • Page 56: Boot Loader

    Installing Applications Applications can be installed on the MX9 from CAB files. CAB files are (re)installed after a cold boot, but not after a suspend/ resume since the OS was not reset and the CAB files are still in use. An unsigned executable (CAB or package file) prompts the user when executed: The program is from an unknown publisher.

  • Page 57: Start Menu

    The main screen for the MX9 is known as the Today screen. The Today screen shows various options and status icons. The Today screen appearance is configurable by selecting Start > Settings > Today. Both the appearance of the Today screen and the items displayed may be configured.

  • Page 58: Notification Bar

    When the MX9 is locked, tapping on Unlock at the bottom of the screen unlocks the MX9. Depending on the settings, a password may be required. The MX9 can also be configured to lock after a period of inactivity. For more information, see the Lock settings later in this section.

  • Page 59: Soft Keys

    Options to set up the default home page, view browsing history, setup privacy and security, preferred language, and Other options. If an Internet Explorer web page is larger than the MX9 screen can display at one time, use touch screen gestures for hori- zontal and vertical scrolling.

  • Page 60: Windows Media

    HSMConnect (or LXEConnect) allows a user with an ActiveSync connection between a PC and the MX9 to display the MX9 screen on the host PC. Any keystrokes on the host PC are passed to the MX9 as if they were keystrokes on the MX9 key- pad.

  • Page 61: Mx9 Os Upgrade

    Tools required: standard size Phillips screwdriver (customer supplied). The expansion slots in the MX9 are accessible via the hatch. The hatch can be opened using a standard size screwdriver. When the hatch is opened, the MX9 automatically shuts down. It is good practice to save any changes then perform an orderly shutdown to preserve RAM contents before opening the hatch.

  • Page 62: Procedure

    3. SD card is located in the front half of the MX9 assembly. Procedure While the hatch is open slide the installed SD card out of the slot. The MX9 may not have a SD card in the slot because the OS is in flash.
  • Page 63 (page 5-71). File Explorer. Displays a structured picture of files on the system. See File Explorer (page 5-72). Help. Access Windows Mobile help system on the MX9. Options to search using Windows Live Search are available. See Help (page 5-73).

  • Page 64: Office Mobile

    (page 5-23). Windows Live. Sign in to Microsoft Windows Live online service. Internet access required. See Windows Live Setup (page 5-76) Windows Media. Audio visual management program. Not supported on the MX9. See Windows Media (page 5-76) Office Mobile Excel Mobile. Spreadsheets can be edited, data can be sorted, formatting and changes are preserved. See Excel Mobile (page 5-80).

  • Page 65: Settings

    (wav) files to OS events. Today (page 5-23). Configure the Today screen. Connections Panel (page 5-65). Set up various connections between a host and the MX9. Personal Panels (page 5-24). Configure Buttons, Input method and Owner information. System Panels (page 5-30).
  • Page 66 Backlight (page 5-33). Set the display backlight brightness and display/keypad backlight timeout. Configure the timeout based on type of power source: battery or external power. Bluetooth. Discover then pair with nearby discoverable Bluetooth devices. See Bluetooth Configuration (page 7-1). Certificates (page 5-35).

  • Page 67: Connections

    (page 5-57). Set up the wireless Wide Area Network. The WAN utilizes a cellular network instead of a spread spectrum network. Connections Beam (page 5-65). Enable receiving InfraRed and Bluetooth beams. (Not supported on the MX9.) Connections (page 5-66). Configure connections to servers. Domain Enroll (page 5-67).
  • Page 68 The Versions tab displays the versions of many of the software programs installed. Not all installed software on the mobile device is included in this list and the list varies depending on the applications loaded on the MX9. The Image line displays the revision of the system software installed.

  • Page 69: Clock & Alarms

    Clock & Alarms Time Adjust the settings and tap ok to save the changes. Select Yes on the popup box and the changes take effect immedi- ately. The Time can be set for both a Home and a Visiting location. Alarms To set an alarm: 5 - 15...

  • Page 70: More

    1. Tap the check box to enable the alarm. If the check box has a check mark, the check mark is removed. If the check box is empty, a check mark is placed in the check box when tapped. 2. Tap < Description > and enter a description. The description is limited to 63 characters. 3.

  • Page 71: Lock

    Windows Classic Prompt if phone unused for Tap the check box to enable (checked) and set the inactivity timeout before the MX9 locks. Password Type When selecting a Password type the screen displays a numeric keypad or the input panel depending on the type of password selected.

  • Page 72: Hint

    Hint If the password entry isn’t successful after a predefined number of attempts, the password hint is displayed. Display Unlock display defaults to Windows Classic. Windows Default can be selected to be the unlock display. Changing the unlock display, and tapping OK (at the top right corner of the screen) presents the following screen: Tap Yes to restart, or cold boot.

  • Page 73: Power

    Power Reports the current battery state and allows the user to set suspend timeouts. Battery Battery power is displayed for both the main and internal Super-cap batteries. 5 - 19...

  • Page 74: Advanced

    Turn off device if not used for Enabled Timer setting 5 minutes Select the inactivity timeout period before the MX9 goes into suspend. The settings on this panel are for the suspend timers only. Backlight timers are set using the Backlight (page 5-33) settings panel.

  • Page 75: Sounds & Notifications

    Sounds & Notifications Set volume parameters and assign sound WAV files to Windows Mobile events. Options that cannot be edited by the user are dimmed. Setting Default Sounds Events Enabled Programs Enabled Notifications Enabled Screen taps Disabled Hardware buttons Disabled Notifications Play Sound Disabled...

  • Page 76: Notifications

    Notifications The Event box lists several events that can have an associated notification. The notification, depending on the event selected, may consist of playing a sound, displaying a screen message, flashing a light or triggering the vibration motor. When finished, tap ok to save the changes. Vibrations Vibration on Screen taps is disabled by default.

  • Page 77: Today

    The Today timeout timer refers to the “return to Today screen” function. When the device is placed in Suspend, and the timer expires, a return from Suspend displays the Today screen, not the application in focus when the MX9 was placed in Suspend.

  • Page 78: Personal Panels

    Personal Panels Buttons Program Buttons Program buttons can be used to assign functions to certain keys such as F1 through F5 and the diamond keys. Buttons can only be assigned to programs that have an icon in the Start menu or the Settings folder (including sub-folders). A program that is not in the above mentioned locations does not show up in the list here.

  • Page 79: Up/Down Control

    Up/Down Control Move the sliders with the stylus to customize the delay before repeating and the repeat rate for the up/down controls. 5 - 25...

  • Page 80: Input

    Input Input Method Select the preferred method of input. The default method of input is the keyboard or input panel. When the cursor is located in a field allowing text input, the input panel may automatically be displayed. If not automatically displayed, the input panel can be accessed by tapping on the keyboard icon at the bottom center of the screen.

  • Page 81: Word Completion

    Word Completion Setting Default Suggest words when entering text Enabled Suggest after entering A space Suggest _ word(s) Add a space after word Enabled Enable auto correct Enabled 5 - 27...

  • Page 82: Options

    Options Setting Default Voice recording format 8000 Hz, 8 Bit, Mono Default zoom level for writing 200% Default zoom level for typing 100% Capitalize first letter of sentence Enabled Scroll upon reaching the last line Enabled 5 - 28...

  • Page 83: Owner Information

    Owner Information Set the MX9 owner details. Setting Default Identification Name, Company, Address, Telephone, E-mail Blank Notes Notes Blank Enter the information and tap ok to save the changes. The changes take effect immediately. Note: Owner Identification name listed in Start > Settings > Personal > Owner > Information is not used during Bluetooth operation.

  • Page 84: System Panels

    System Panels About The About panels show OS versions, allow device name and description input and display copyright information. The fol- lowing screens are examples only. Version This screen displays information on the installed operating system and the hardware. Note that Windows Mobile is based on a Windows CE engine. The underlying version of Windows CE is displayed here.

  • Page 85: Device Id

    Device Name [device_specific]001 Device Description WM_ MX9 The device name and description can be changed. Enter the name and description using either the keypad or the Input Panel and tap ok to save the changes. The changes take effect immediately.

  • Page 86: Copyrights

    Copyrights This screen is presented for information only. The Copyrights information cannot be changed by the user. 5 - 32...

  • Page 87: Backlight

    Power key press. When the MX9 is on battery power and the backlight timer expires, the display and the backlights for the display and keypad are turned off. Default value is 30 seconds and both the check boxes are enabled. Adjust the settings and tap OK to save the changes.

  • Page 88: External Power

    When the MX9 is on external power and the backlight timer expires, the display and the backlights for the display and keypad are turned off. Default value is 1 minute and both the check boxes are enabled. Adjust the settings and tap ok to save the changes.

  • Page 89: Certificates

    Certificates Manage digital certificates used for secure communication. View – displays details of the certificate. Personal certificates may be extended from the view screen. Delete – removes the certificate from the device. Delete is not available if the certificate was installed by a device adminis- trator.

  • Page 90: Intermediate

    To install an Intermediate certificate: 1. Copy a DER-encoded .cer file, a base64-encoded .cer file or a .pfx file to a folder on the MX9. 2. Use File Explorer to browse to the location of the file and open the file by tapping the file name.

  • Page 91: Root

    To install a Root certificate: 1. Copy a DER-encoded .cer file, a base64-encoded .cer file or a .pfx file to a folder on the MX9. 2. Use File Explorer to browse to the location of the file and open the file by tapping the file name.

  • Page 92: Encryption

    Encryption This panel enables or disables encryption of data files on removable storage cards. The default is Disabled. There may be a delay while files on removable storage cards are encrypted. 5 - 38...

  • Page 93: External Gps

    External GPS Setting Default GPS Program Port None GPS Hardware Port None Baud Rate 4800 Access Automatic This panel configures serial GPS access over hardware serial ports using the Microsoft GPS manager. The port used, baud rate and port sharing must be specified. In order to use the configuration items on these panels, applications must use the Microsoft GPS API interface rather than reading the serial port directly.

  • Page 94: Hardware

    Hardware Access 5 - 40...

  • Page 95: License Manager

    Note: Following image is a sample screen. Your License Manager panel may show more tabs, e.g., RFTerm, depending on the number of software applications run- ning on the MX9 that require a license. Information on this panel cannot be edited by the user.

  • Page 96: Managed Programs

    Managed Programs This panel displays the install history for .NET managed programs. The list is read only. Remove Programs (page 5-53). 5 - 42...

  • Page 97: Memory

    Memory These panels report the current state of virtual memory. Main The split between Storage memory and Program memory is not adjustable. Storage Card The pop-up list shows all mounted storage, both fixed and removable. The Find prompt at the bottom of the screen launches the Search utility.

  • Page 98: Mixer

    Mixer The MX9 has a speaker located above the scan button. It is active when a headset is not connected to the device. Use the settings on these panels to adjust the volume, record gain and sidetone for microphone input, speaker and speaker output.

  • Page 99: Mx9Wm Options

    By default, TCP/IP version 6 is enabled and dimmed on the MX9. By default, the Remote Desktop Autologin is disabled. Tap this check box to enable Remote Desktop Autologon. Autolaunch TimeSync enables time synchronization when the MX9 boots. Tap this check box to enable TimeSync to autolaunch.

  • Page 100: Misc

    Enable Keypad Backlight is enabled by default. Uncheck this check box to disable the keypad backlight. Enable Ethernet on AC Power and Battery are enabled and dimmed. Ethernet is only available when the MX9 is docked in a powered desktop cradle.

  • Page 101: Status Popup

    Status Popup When the Status popup window is enabled, and displayed, it is placed on top of the window in focus and hides any data beneath it. The Status Popup window is closed by pressing the assigned Status User or Status Admin key sequence. Note: Use a Diamond key for the assigned key sequence to use when opening and closing the popup.

  • Page 102: Peripherals

    Peripherals This panel is used to enable and disable the touch screen heater and scan window heater, flashlight time delay to Off, and GPS On/Off. Settings have no effect if module is not installed. Setting Default Heaters Touch screen heater Enabled Scan window heater Enabled...

  • Page 103: Flashlight

    Flashlight Note: Setting has no effect if the flashlight is not installed. Select an option to set the timeout for the flashlight. Options are: • 1 minute • 2 minutes • 3 minutes 5 - 49...

  • Page 104: Gps

    GPS presence is displayed on the GPS panel. Power can be toggled on or off only when a GPS is installed. The default setting is Off. Regional Settings 5 - 50...
  • Page 105 5 - 51...

  • Page 106: Registry

    Registry Choose an MX9 software reload scheme. Load User Defaults Button When tapped, a standard load file dialog is opened, to allow the user to pick a Registry Save (.RSG) file. The applet then copies the specified User registry file to the Active registry. The user is asked to verify a reboot, and then the applet does a warmboot to activate the new registry.

  • Page 107: Remove Programs

    Remove Programs This panel is used to uninstall programs. The Remove Program listing is for all programs installed via ActiveSync or via a CAB file. Screen General 5 - 53...

  • Page 108: Align Screen

    Align Screen Tap the Align Screen button. The align screen opens and displays a large cross-hair in the middle of the screen. Tap the middle of the cross-hair as it moves around the screen. When the process is complete, the General screen is dis- played.

  • Page 109: Text Size

    Text Size Tap the marker and slide it across the bar. As the marker moves, the example text increases or decreases. Tap ok and the change is saved. The new text size is in effect immediately. 5 - 55...

  • Page 110: Task Manager

    If memory runs out, the programs are released from memory. However, to avoid out of memory operational problems, it is best to manually terminate unwanted tasks using this option. Wi-Fi Use this option to set parameters and manage profiles for the wireless client in your MX9. Summit Client Utility (page 11-1) (SCU) for more information.

  • Page 111: Wan

    These panels can be used to set the parameters for the wireless Wide Area Network (WAN) on the MX9. The WAN is a form of wireless network that utilizes a cellular network instead of the spread spectrum network most used by wireless Local Area Networks (LAN).

  • Page 112: Initial Setup

    Initial Setup 1. Enable the radio by tapping the Admin Login button on the Connection panel (the Connect button is dimmed). 2. Enter the password in the Admin Password Entry popup text box. The default case-sensitive password is LXEW- WAN. The Connect button is enabled. 3.

  • Page 113: Connection

    OK button. Admin Login causes all dimmed buttons and configurable fields on Network, TCP/IP, Autoconnect, and Admin tabs to be enabled. Network Enter the following information for the MX9: • Phone (data access number) • Username 5 - 59...
  • Page 114 • Password • APN (Access Point Name) Note: Some fields may not require an entry. Contact your system administrator for the information needed. 5 - 60...

  • Page 115: Tcp/Ip

    TCP/IP The TCP/IP tab contains a check box for indicating that TCP/IP parameters are to be obtained from the network DHCP server. This tab also contains fields for entering a static IP address and the addresses of the primary and secondary DNS servers, if DHCP and DNS are not used.

  • Page 116: Autoconnect

    Autoconnect The Autoconnect tab contains two checkboxes. Automatically connect to network when device is turned on. When this check box is enabled (checked) the radio auto- matically connects to the network when the device is turned on (power button is pressed). Automatically reconnect to network when connection lost or resuming from suspend.

  • Page 117: Admin

    SIM card PIN number entry is locked from further use. If the radio is disabled, entering and submitting the PIN saves the PIN value on the MX9. The next time the radio is enabled and requires a PIN, the saved PIN will be sent and a PIN will not need to be entered again.

  • Page 118: About

    About The About tab displays information about the WWAN radio and the current network connection. The About tab displays the SW Version, FW Version and Serial Number of the radio if there is a WAN radio installed in the device. the Local Phone Number shows the subscriber’s own number from the SIM card.

  • Page 119: Connections Panel

    Enable or disable receiving OBEXdata beams, either by IrDA or Bluetooth. Note: The MX9 does not support beaming. The default setting for Beam Settings is Disabled as the MX9 does not support beaming. A communications protocol used to exchange information between...

  • Page 120: Connections

    Connections Configure connections to a host PC. Advanced Panel Options: 5 - 66...

  • Page 121: Domain Enroll

    Domain Enroll Enroll in Active Directory. To begin enrollment, tap Enroll in the Status bar. Contact your system administrator for the applicable information to com- plete the screens. 5 - 67...

  • Page 122: Network Cards

    Network Cards This panel displays a listing of network adapters. The list is based on drivers installed in the registry whether the adapter is actually supported by the hardware or not. The Network Cards may not always be displayed. If this icon is not displayed, access Network Cards by selecting Start > Settings >...

  • Page 123: Wireless Manager

    The Bluetooth radio is off The Bluetooth radio is on Visible The MX9 is discoverable If the Bluetooth radio is Off, tapping the Bluetooth bar turns the radio On. Once the radio is On, it may cycle to Visible if the MX9 is discoverable.

  • Page 124: Miscellaneous Start Panels

    Miscellaneous Start Panels Standard Microsoft Applications Note: The intent of this segment is to document standard Microsoft applications loaded on the MX9. Documentation only consists of a panel and minimal explanation. These are standard Microsoft small form applications for which help is available on the MX9 and the Internet.

  • Page 125: Address Book

    Address Book Address book application. Contacts can be synchronized with PC Outlook address book using ActiveSync. Email Email application. Can be synchronized with PC Outlook email using ActiveSync or it can synchronize with an Exchange server. 5 - 71...

  • Page 126: File Explorer

    File Explorer File Explorer displays a structured picture of files on the system. Getting Started This application provides several wizards to walk a user through device configuration. 5 - 72...

  • Page 127: Help

    Help Access Windows Mobile help system on the MX9. Options to search using Windows Live Search are available. Windows Live Messenger Windows Live Messenger. Instant Messaging service. Internet access required. Not supported on the MX9. 5 - 73...

  • Page 128: Notes

    Notes Notes. Notebook application. Select Menu > View Recording Toolbar to create an audio note. Can be synchronized with PC Outlook notes using ActiveSync. Pictures and Video Pictures and Video. Picture/video viewer application. Can be synchronized with PC My Documents folder using ActiveSync. 5 - 74...

  • Page 129: Tasks

    Tasks Tasks. Task list application. Can be synchronized with PC Outlook task list using ActiveSync. Text Messaging Text Messaging application. Can be synchronized with PC Outlook email using ActiveSync or it can synchronize with an Exchange server. 5 - 75...

  • Page 130: Windows Live Setup

    Windows Live Setup Windows Live. Sign in to Microsoft Windows Live online service. Internet access required. Windows Media Windows Media. Audio visual management program. Not supported on the MX9. 5 - 76...

  • Page 131: Internet Explorer Mobile

    Internet Explorer Mobile Set options for Internet connectivity. The navigation icons change state based on the web page contents. Navigation Icon Action Navigation Icon Action Add folder Favorites Add to Favorites Options Go Back Soft Input Panel Delete Favorite Zoom In / Zoom Out Edit Favorites 5 - 77...

  • Page 132: Options

    Options 5 - 78...
  • Page 133 5 - 79...

  • Page 134: Office Mobile

    Office Mobile A suite of business related applications. Files can be created, opened, viewed, saved in different formats, etc. Note: For Microsoft Office Mobile instruction for Word, PowerPoint, Excel and OneNote, refer to commercially available Microsoft Office Mobile user guides. Excel Mobile Spreadsheets can be edited, data can be sorted, formatting and changes are preserved.

  • Page 135: Word Mobile

    Word Mobile Open, view, edit documents. Formats are saved. Spelling checker, cut and paste are available, undo and redo com- mands. Select Menu > Options to change default settings. OneNote Mobile Open, view, edit text-only notes. Select Menu to change default settings. 5 - 81...

  • Page 136: Remote Desktop

    For example, instead of running Word Mobile on the MX9, you can run the desktop computer version of Word and access all of the .doc files on that computer from your device.
  • Page 137 1. Configure the radio. 2. Enter the name of the computer to which you want to connect. If needed, enter the port number at the end of the computer name (remotecomputername:portnumber). 3. Enter the user name, password and domain. 4. Tap the Save password check box if it is blank. 5.

  • Page 138: Using Activesync

    The default connection type is USB Client. This is the only connection option supported on the MX9. Connect the USB cable to the host computer and the MX9 (the client) as detailed below. ActiveSync will start automat- ically when the USB cable is connected.

  • Page 139: Explore

    Explore From the ActiveSync Dialog on the host computer, tap the Explore button, which allows you to explore the MX9 from the PC side, with some limitations. You can copy files to or from the mobile device by drag-and-drop. You will not be allowed to delete files or copy files out of the \Windows folder on the mobile device.

  • Page 140: Activesync Help

    HSM Connect allows a user to view the MX9 screen remotely from a host computer using the ActiveSync connection. ActiveSync is already installed on the MX9. The MX9 is configured to establish a USB ActiveSync connection to a host PC when the USB cable is attached to the MX9 and the host PC.

  • Page 141: Install Hsm Connect

    Using HSM Connect 1. Power up the MX9. 2. Connect the MX9 to the host PC using the USB connection cable. Once connected, the ActiveSync dialog box appears and the ActiveSync connection is automatically established. 3. Select “No” for partnership when prompted. Dismiss any ActiveSync dialog boxes warning a partnership is not set up.
  • Page 142 6. Tap the OK button to dismiss the About CERDisp dialog box on the MX9 desktop by tapping the OK button in the HSM Connect window on the PC desktop. The dialog box automatically times out and disappears after approxi- mately 20 seconds.

  • Page 143: Chapter 6 - Applock (Application Locking)

    MX9 and no password prompt is displayed. After the administrator specifies applications to lock, a password is assigned and the device is rebooted or the hotkey is pressed, the MX9 switches to end-user mode.

  • Page 144: Administration Mode

    Administration Mode Administration mode gives full access to the mobile device, hardware and software configuration options. The administrator must enter a valid password (when a password has already been assigned) before access to Administration mode and configuration options are allowed. The administrator can configure the following options: •...

  • Page 145: Passwords

    A checkmark in the switchpad menu (see image above) indicates applications currently active or available for Launching by the user. When Keyboard is selected, the MX9 default input method (Input Panel, Transcriber, or custom input method) is activated. The check to the left of the application name indicates that the application is active.

  • Page 146: Hotkey (Activation Hotkey)

    Hotkey (Activation hotkey) If the mobile device uses AppLock to allow the user to switch between applications, the default Activation key is Ctrl+Spc. The key sequence switches the focus between one application and another. Data entry affects the application running in the foreground only.

  • Page 147: Application Configuration

    Use the Application tab options to select the applications to launch when the device boots up in End-user Mode. If no application is specified when the Administrator Panel is closed, the MX9 reboots into Administrator mode. If a pass- word has been set, but an application has not been specified, the user will be prompted for the password before entering administration mode.
  • Page 148 Option Explanation Internet Default is Disabled. Enable the Internet checkbox to use the End-user Internet Explorer (EUIE.EXE) When the checkbox is enabled, the Internet Menu and Internet Status are available. See the section titled End User Internet Explorer (EUIE) (page 6-4) for more details. Launch Button See following section titled Launch Button...

  • Page 149: Launch Button

    Launch Button When the Launch button is clicked, it displays the Launch options panel for the Filename selected on the Administra- tion panel. Note: Launch order is determined by the Order specified in the Application tab. The Order value does not have to be sequential.

  • Page 150: Auto Re-Launch

    Auto Re-Launch Default is Enabled. When enabled for a specific application. automatically re-launches it (subject to the specified Auto Re-Launch Delay in seconds) after it terminates. This option allows the Administrator to disable the re-launch operation. AppLock cannot prevent all applications from closing. When an application that AppLock cannot prevent from closing terminates, per- haps because of an error condition, AppLock re-launches the application when this option is enabled.

  • Page 151: Allow Close

    Allow Close Default is Disabled. When enabled, the associated application can be closed by the end-user. This option allows the administrator to configure applications that consume system resources to be terminated if an error condition occurs or at the end-user’s request. Error conditions may generate a topmost popup requiring an end- user response, memory resource issues requiring an end-user response, etc.

  • Page 152: Setting A Password In The Security Panel

    Setting a Password in the Security Panel Move the cursor to the Password text box. The passwords entered in the Password and Confirm Password fields must match. Passwords are case sensitive. When the user exits the Administrator panel, the two passwords are compared to verify that they match. If they do not match, a dialog box is displayed notifying the user of the error.

  • Page 153: Status Panel

    Status Panel Use the Status panel to view the log of previous AppLock operations and to configure which messages are to be recorded during AppLock operation. Status information is stored in a specific location on the storage device and in a specific logfile specified by the Administra- tor.

  • Page 154: Log

    Solution: When the Administrator is selecting a hotkey sequence to use when switching user modes, they are not allowed to enter key combinations that are reserved by installed software applications. Honeywell has validated RFTerm key combinations ONLY. When RFTerm is installed on the mobile device and an RFTerm restricted key sequence is specified as a hotkey sequence by the Administrator, the following error message is displayed in a message box: Selected hotkey is not allowed.

  • Page 155: Applock Error Messages

    AppLock Error Messages Any messages whose first word ends in ‘ing’ is output prior to the action described in the message. For example, “Switching to admin-hotkey press” is logged after the administrator has pressed the hotkey but prior to starting the switch process. For all operations that can result in an error, an Error level message is displayed when a failure occurs.
  • Page 156 Message Explanation and/or corrective action Level Cannot find kbdhook.dll The load of the keyboard filter failed. This occurs LOG_ERROR when the dll is missing or is corrupted. Look in the \Windows directory for kbdhook.dll. If it exists, delete it. Also delete AppLock.exe from the \Windows directory and reboot the unit.
  • Page 157 Message Explanation and/or corrective action Level Enter AppLockEnumWindows In order for AppLock to control the application being LOG_EX locked so it can prevent the application from exiting, AppLock launches the application and has to wait until it has created and initialized its main window. This message is logged when the function that waits for the application initialization is entered.
  • Page 158 Message Explanation and/or corrective action Level Exit ToAdmin Exiting the function that handles the mode switch LOG_PROCESSING into admin mode. Exit ToUser Exiting the user mode switch function. LOG_PROCESSING Exit ToUser-Registry read failure The AppName value does not exist in the registry so LOG_PROCESSING user mode cannot be entered.
  • Page 159 Message Explanation and/or corrective action Level Loading keyboard hook When AppLock first loads, it loads a dll that contains LOG_PROCESSING the keyboard hook processing. This message is logged prior to the load attempt. Open failure The status information is being saved to a file and LOG_ERROR the file open has failed.
  • Page 160 Message Explanation and/or corrective action Level Registry read failure The registry read failed. The registry information LOG_ERROR read when this message is logged is the application information. It the Administration key cannot be opened or if the AppName value is missing or empty, this error is logged.
  • Page 161 Message Explanation and/or corrective action Level Timeout looking for app window After the application is launched, AppLock must wait LOG_ERROR until the application has initialized itself before proceeding. The application did not start successfully and AppLock has timed out. ToUser after admin, not at boot The user mode switch is attempted when the device LOG_EX boots and after the administrator presses the...
  • Page 162 6 - 20...

  • Page 163: Chapter 7 - Bluetooth Configuration

    Bluetooth Configuration Introduction Discover and manage pairing with nearby Bluetooth devices. Contact Technical Assistance (page 16-1) for upgrade availability if your Bluetooth panels are not the same as the panels presented in this section. Setting Default Discovered Devices None Settings Bluetooth button (Toggle client On/Off) Bluetooth client is Off.
  • Page 164 • It is not necessary to disconnect a paired scanner and printer before a different scanner or printer is paired with the MX9. • The target Bluetooth device should be as close as possible (up to 32.8 ft (10 meters) Line of Sight) to the MX9 during the pairing process.

  • Page 165: Initial Configuration

    LED on the device, or a dialog box is placed on the MX9 display. 14. Whenever the MX9 is turned On, all previously paired, live, Bluetooth devices in the vicinity are paired, one at a time, with the MX9.

  • Page 166: Bluetooth Devices

    When the Discover button is tapped, the Bluetooth client discovers and displays all Bluetooth devices in the vicinity. Blue- tooth managed devices should be as close as possible, in direct line of sight, with the MX9 during the Discover process.

  • Page 167: Discovering

    2. Tap Stop at any time to end the Discover and Query for Unique Identifier functions. Note: When an active paired device enters Suspend Mode, is turned Off or leaves the MX9 Bluetooth scanning range, the Bluetooth connection between the paired device and the MX9 is lost. There may be audible or visual signals as paired devices disconnect from the MX9.
  • Page 168 An icon with a red background indicates the device's Bluetooth connection is inactive. An icon with a white background indicates the device is connected to the MX9 and the device's Bluetooth connection is active. Double-tap a device in the list to open the device properties menu. The opened device does not need to be active.

  • Page 169: Bluetooth Device Menu

    Communicate with the highlighted DUN (Dial-Up Networking) device. This option is available when Filtered Mode is dis- abled/unchecked. Disconnect Stop the connection between the MX9 and the highlighted paired Bluetooth device. Delete Remove an unpaired device from the Bluetooth device list. The highlighted device name and identifier is removed from the MX9 Bluetooth Devices panel when the user taps the Clear button.

  • Page 170: Bluetooth Properties

    Bluetooth Properties Data on the Bluetooth Properties panel cannot be changed by the user. The data displayed is the result of the device Query performed during the Discovery process. The Status dialog box reflects the current state of the highlighted device. Settings Note: Options can be checked or unchecked whether Bluetooth connection is enabled or disabled.

  • Page 171: Reconnect

    Prompt if devices request to pair This option is Enabled (checked) by default. A dialog box appears on the MX9 screen notifying the user a Bluetooth device requests to pair with the MX9. The requesting Bluetooth device does not need to have been Discovered by the MX9 before the pairing request is received.

  • Page 172: Options

    Options Report when connection lost This option is Enabled by default. There may be an audio or visual signal when a connection between a paired, active device is lost. A visual signal may be a dialog box placed on the display notifying the user the connection between one (or all) of the paired Bluetooth devices has stopped.

  • Page 173: About

    About This panel shows the Computer Friendly Name (that other devices may discover during their Discovery and Query process), the Bluetooth Client MAC address, and software version levels. The data cannot be edited by the user. 7 - 11...

  • Page 174: Easy Pairing And Auto-Reconnect

    MX9 is out of range of all paired Bluetooth device(s). Connection is inactive. Note: When an active paired device enters Suspend Mode, is turned Off or leaves the MX9 Bluetooth scan range, the Bluetooth connection between the paired device and the MX9 is lost. There may be audible or visual signals as paired devices disconnect from the MX9.

  • Page 175: Mx9 With Label

    The devices are paired. The Bluetooth bar code reader responds with a series of beeps and an LED flashes. Note: After scanning the MX9 Bluetooth label, if there is no beep and no LED flash from the Bluetooth device, the devices are currently paired.

  • Page 176: Bluetooth Printer Setup

    Refer to the remote Bluetooth printer manufacturer’s User Guide; it may be available on the manufacturer’s web site. Contact Technical Assistance (page 16-1) for Bluetooth product help. Note: If there is no beep or no LED flash from the remote Bluetooth printer, the MX9 and the printer are currently paired. 7 - 14...

  • Page 177: Chapter 8 - Data Collection Wedge

    • Symbol Multi-Range “LORAX” Laser, 1524ER • Hand Held Products 2D Area Imager, 5300 The integrated scan engine activates when the Scan button on the front of the MX9 is depressed or when the trigger on an installed trigger handle is depressed.

  • Page 178: Data Processing Overview

    Data Processing Overview Bar code data processing involves several steps. Some steps may be skipped during the processing depending on user selections on the Symbology Settings panels. The steps are presented below in the order they are performed on the scanned data.

  • Page 179: Main Tab

    The Data Collection Wedge supports up to three concurrent data collection devices. For example, the internal scanner could be used to collect data at the same time a Bluetooth scanner is paired and/or a serial device is attached to COM1. The MX9 must be in a desktop cradle to use a tethered scanner.

  • Page 180: Continuous Scan Mode

    Continuous Scan Mode Continuous scan mode is only available if the MX9 is equipped with a Symbol scanner. Continuous scan mode draws power from the main battery every time a scan read/decode sequence is performed. Enabling Continuous Scan Mode will ensure the laser is always on and decoding.

  • Page 181: Com1 Tab

    If these values are changed, the default values are restored after a cold boot or reflashing. Note: COM1 does not support 5V switchable power on Pin 9 for tethered scanners connected to the MX9 I/O port. Tethered scanners must be connected to a MX9 cradle.

  • Page 182: Notification Tab

    Vibration Vibration on the MX9 is activated when a scan is completed successfully or with a failure (scan key released before good scan, timeout, or rejected because of Data Options configuration). It is not activated when a trigger or scan key is pressed.
  • Page 183 Volume and Vibration Since the Data Collection Wedge uses the operating system interface to emit sounds/beeps, if the volume/vibrate icon is set to anything other than On, Wedge beeps do not sound. Wedge vibration is not affected by the System setting. Beep/sound volume and vibration can be quickly toggled on and off by tapping the volume icon on the Windows Mobile Today screen.

  • Page 184: Data Options Tab

    Bar code manipulation parameter settings on this tab are applied to the incoming data resulting from successful bar code scans sent to the MX9 for processing. Note: The Data Options tab contains only those options available for one type of decoding engine.

  • Page 185: Enable Code Id

    Panel for a Hand Held Products scan engine Panel for Symbol scan engine The HHP Properties button is only present if the MX9 is equipped with a Hand Held products imager. 1. Choose an option in the Enable Code ID drop-down box: •...

  • Page 186: Symbology Settings

    • The external scanner operation cannot be controlled by the MX9 scanner driver; therefore, a ‘good’ beep may be sounded from the external scanner even if a bar code from an external scanner is rejected because of the configuration specified.

  • Page 187: Processing Order

    Each time a Symbology is changed, the settings are saved as soon as ok is clicked. Settings are also saved when a new Symbology is selected from the Symbology drop down list. Clear Button This button will erase any programmed overrides, returning to the default settings for the selected symbology. If Clear is pressed when All is selected as the symbology, a confirmation dialog appears.

  • Page 188: Strip Leading/Trailing Control

    Enable, Min, Max Enable This checkbox enables (checked) or disables (unchecked) the symbology field. The scanner driver searches the beginning of the bar code data for the type of ID specified in the Data Options tab -- Enable Code ID field plus any custom identifiers. When a code ID match is found as the scanner driver processes incoming bar code data, if the symbology is disabled, the bar code is rejected.

  • Page 189: Barcode Data Match List

    Barcode Data Match List The Barcode Data panel is used to strip data that matches the entry in the Match list from the bar code. Enter the data to be stripped in the text box and tap the Insert or Add button. The entry is added to the Match list. To remove an entry from the Match list, highlight the entry in the list and tap the Remove button.

  • Page 190: Add Prefix/Suffix Control

    together. More than one * in a configuration string is not allowed. (The User Interface will not prevent it, but results would not be as expected, as only the first * is used in parsing to match the string.) • The question mark wildcard ? may be used to match any single character in the incoming data. For example, the data AB?D will match ABCD, ABcD, or AB0D, but not ABDE.

  • Page 191: Symbologies

    Symbologies The Code ID drop-down box filters the available symbologies, in the Symbology drop down box, by the selected Code ID. When a Hand Held Products imager scan engine is installed, AIM, Custom and HHP symbologies are displayed. HHP does not support Symbol IDs.

  • Page 192: Hhp Symbologies

    HHP Symbologies Advanced properties are available when an integrated Hand Held Products imager is installed. Advanced properties are applicable regardless of the ID type selected (AIM or HHP). HHP = Hand Held Products. Not all HHP symbologies have Advanced options. Click the symbology link in the table below for the symbology Advanced options.
  • Page 193 Codabar - Advanced Properties Check Character Required – When enabled, the check character is required. Default is disabled. Transmit – When enabled, the check character is transmitted. Default is disabled. Start / Stop Character Transmit – When enabled, the start / stop characters are transmitted. Default is disabled. Code 11 - Advanced Properties Check Digits Required –...
  • Page 194 Code 39- Advanced Properties Check Character Required – When enabled, the check character is required. Default is disabled. Transmit – When enabled, the check character is transmitted. Default is disabled. Transmit Start / Stop Character – When enabled, the start / stop characters are transmitted. Default is disabled. Full ASCII –...
  • Page 195 Read 5-Digit – When enable, transmit the 5 digit addenda. Default is disabled. Required – When enabled, only transmit bar codes with a 2 or 5 digit addenda. Default is disabled. Insert Separator – When enabled, insert a space between the code and addenda. Default is enabled. EAN 13 - Advanced Properties Transmit Check Character –...
  • Page 196 Interleaved 2 of 5 - Advanced Properties Check Character Required – When enabled, the check character is required. Default is disabled. Transmit – When enabled, the check character is transmitted. Default is disabled. 8 - 20...
  • Page 197 Mesa - Advanced Properties UPCA – When enabled, decode UPCA Mesa. Default is disabled. EAN13 – When enabled, decode EAN 13 Mesa. Default is disabled. Code39 – When enabled, decode Code 39 Mesa. Default is disabled. Code128 – When enabled, decode Code 128 Mesa. Default is disabled. Interleaved 2 of 5 –...
  • Page 198 MSI Plessy - Advanced Properties Transmit Check Character – When enabled, transmit the check character. Default is enabled. 8 - 22...
  • Page 199 OCR Properties - Advanced Properties Font – Font selection. Default is disabled. • A = OCR A • B = OCR B • Money = OCR Money • MICR = Magnetic Ink Character Recognition Direction – Decoder reads OCR fonts in any direction, but setting direction parameter correctly can increase decoding speed.
  • Page 200 2. To read the same string with a modulo 10 check digit in the seventh character position, use the following template: aaaaaac Then enter 0123456789 for the Check parameter. 3. To read either a string of 6 alphabetic letters OR a string of 8 numeric digits, use this template: lllllltdddddddd Note the use of the “t”...
  • Page 201 Posicode - Advanced Properties Limited Labels – Select the type of Posicode Limited labels: • None • A – Posicode Limited A • B – Posicode Limited B Telepen - Advanced Properties Original Output – When enabled, output is Original Telepen. When disabled, output is AIM. Default is enabled. 8 - 25...
  • Page 202 UPCA - Advanced Properties Transmit Check Character – When enabled, transmit the check character. Default is enabled Transmit Number System Digit – When enabled, transmit the number system digit. Default is enabled. Addenda Read 2-Digit – When enabled, transmit the 2 digit addenda. Default is disabled. Read 5-Digit –...
  • Page 203 UPCE0 - Advanced Properties Note: The UPCE0 and UPCE1 parameters are always set to match each other. Therefore if a change is made to a parameter to either the EPCE0 or UPCE1 Advanced Properties that same change is automatically made to the Advanced Properties for the other symbology.
  • Page 204 UPCE1 - Advanced Properties Note: The UPCE0 and UPCE1 parameters are always set to match each other. Therefore if a change is made to a parameter to either the EPCE0 or UPCE1 Advanced Properties that same change is automatically made to the Advanced Properties for the other symbology.

  • Page 205: Hhp Properties

    HHP Properties When the MX9 is equipped with a Hand Held Products imager, this option is used to configure imager parameters. Option Action Centering The centering feature is used to allow the user to accurately scan a selected bar code among a group of bar codes that are located closely together.
  • Page 206 Option Action Aim Time Duration of the imager aim beam in 0.1 second increments. Valid:0 – 50 (0 to 5 seconds) Default:0 Lights Specifies if the imager's lights and aimer should be left on during the entire decode process. The default is disabled. If disabled, the lights are turned on only during image capture, then turned off while the imager attempts to process and decode the bar code.

  • Page 207: Ctrl Char Mapping

    Ctrl Char Mapping The Ctrl Char Mapping button activates a dialog to define the operations the Data Collection Wedge performs on con- trol characters (values less than 0x20) embedded in bar codes. Control characters can be replaced with user-defined text which can include hat encoded or hex encoded values. In key message mode, control characters can also be translated to their control code equivalent key sequences.

  • Page 208: Custom Identifiers

    List Box The list box shows all user-defined control characters and their assigned replacements. All replacements are enclosed in single quotes to delimit white space that has been assigned. Delete This button is grayed unless an entry in the list box is highlighted. When an entry (or entries) is highlighted, and Delete is selected, the highlighted material is deleted from the list box.

  • Page 209: Control Code Replacement Examples

    Entering data into both the Name and ID Code fields enables the Add button. Tap the Add button and the data is added to the next empty location in the Custom ID list. Insert Tap on an empty line in the Custom ID list. The Add button changes to Insert. Enter data into both the Name and ID Code fields and tap the Insert button.

  • Page 210: Bar Code Processing Examples

    Bar Code Processing Examples The following table shows examples of stripping and prefix/suffix configurations. The examples assume that the scan- ner is configured to transmit an AIM identifier. Symbology EAN-128 (]C1) EAN-13 (]E0) Intrlv 2 of 5 (]IO) Code93 Enable Enabled Enabled Enabled...

  • Page 211: Length Based Bar Code Stripping

    Length Based Bar Code Stripping Use this procedure to create symbology rules for two bar codes with the same symbology but with different discrete lengths. This procedure is not applicable for bar codes with variable lengths (falling between a maximum value and a mini- mum value).
  • Page 212 5. Tap the Barcode Data button. 6. Tap the Add button. 7. Add the data for the match codes. 8. Refer to the previous section Barcode Data Match List (page 8-13) for instruction. 9. Scan a bar code and examine the result. 8 - 36...

  • Page 213: Processing Tab

    Processing Tab The Processing tab contains a user configurable key delay that applies to scanned bar codes as they are input when Remote Desktop is the application with the input focus. Setting Default Enable buffered key output Enabled and dimmed Same buffer limit (characters) Delay between (key) buffers 75 ms...

  • Page 214: About Tab

    About Tab The About tab lists the version of the Data Collection Wedge (DCWedge) software and the type of scanner/imager installed in the MX9. Hand Held Products Imager Symbol Scanner Valid scanner / imager types: • HHP – Hand Held Products 5300 2D Imager •...

  • Page 215: Hat Encoding

    Hat Encoding Hat Encoded Characters Hex 00 through AD. 8 - 39...
  • Page 216 Hat Encoded Characters Hex AE through FF. 8 - 40...

  • Page 217: Chapter 9 - Enhanced Launch Utility

    Enhanced Launch Utility Introduction The launch utility has two functions: • Process registry based Launch items • Process script based Launch items. The registry based Launch items are processed before the script based Launch items. Registry Based Launch Items Note: The Registry based Launch items (documented here) are processed before the Script Based Launch items. The Launch utility can use registry entries to auto-launch Windows CAB files.

  • Page 218: Launch Startup Options

    • The Order field is used to force a sequence of events; Order=0 is first, and Order=99 is last. Two items which have the same order are installed in the same pass, but not in a predictable sequence. • The Delay field is used to add a delay after the item is loaded, before the next is loaded. The delay is given in seconds, and defaults to 0 if not specified.

  • Page 219: Script Based Launch Items

    Script Based Launch Items Note: The Script Based Launch items (documented here) are processed after the Registry Based Launch items. The Enhanced (script based) portion of the Launch utility provides several features: • Launch .CAB file • Run .EXE file •...

  • Page 220: Command Line Structure

    Command line structure Each command takes up one line. Every command uses the format: COMMAND,PARAMETER1,PARAMETER2,...etc. Parameters are separated by a single comma. If a parameter requires a comma within it, the whole parameter must be enclosed in quote marks ("). Extra spaces are ignored between the comma and the next parameter. For Example To delete a file called Ive, got, commas, in, my, name.txt, use the command delete,"Ive, got, commas, in, my, name.txt".

  • Page 221: Commands Supported By Launch

    Commands Supported by Launch Copy ElseIfFile IfFile Mkdir Delete EndIf IfTerm Rmdir DelRegData EndIfFile Launch SetRegData DelRegKey EndIfTerm LaunchCmd SetRegKey ElseIf FCopy Message Shortcut The commands supported by Launch are detailed below. Square brackets indicate that a parameter is optional. Characters in Italics represent a variable, and not a literal.

  • Page 222: Delregkey

    DelRegKey Description Deletes a specified registry subkey. Syntax Delregkey,key,subkey Parameter key: The abbreviated major registry key where you want to delete the subkey. Can be one • cr or hkcr (HKEY_CLASSES_ROOT) • cu or hkcu (HKEY_CURRENT_USER) • lm or hklm (HKEY_LOCAL_MACHINE). The case of key does not matter.

  • Page 223: Endif

    EndIf Description Ends conditional command block begun with the previous IF command. Syntax EndIf Parameter None Example IfFile (page 9-8). Notes Results are unpredictable if not paired properly with If... command. EndIfFile Description Ends conditional command block begun with the previous IF command. Syntax EndIfFile Parameter...

  • Page 224: Iffile

    IfFile Description Begins the conditional execution of a block of commands only if the specified file exists. Syntax IfFile,file Parameter file: The path and filename to determine if the commands should be executed Example IfFile,\System\MyData.dat any number of commands, executed if file exists ElseIfFile any number of commands, executed if file does not exist EndIfFile...

  • Page 225: Launchcmd

    LaunchCmd Description Runs a program with arguments. Syntax Launchcmd,program,arguments,wait-code Parameters program: The full path and filename of the program to be run. arguments: The command line arguments for program. wait-code: Tells Launch how to behave when the program is running. w(ait) causes Launch to stop processing the script until the program has finished executing.

  • Page 226: Rmdir

    Rmdir Description Removes a directory. Syntax Rmdir,dir Parameters dir: The full path and name of the directory to be removed. Example rmdir,\Program Files\MyApp Notes A directory cannot be removed if it contains files or subdirectories. SetRegData Description Adds or updates a data field in the registry. Syntax Setregdata,key,subkey,type,field,data[,data2][,data3]...

  • Page 227: Setregkey

    SetRegKey Description Adds a sub key to the registry. Syntax Setregkey,key,subkey Parameters key: The abbreviated major registry key where you want to create the subkey. Can be one • cr or hkcr (HKEY_CLASSES_ROOT) • cu or hkcu (HKEY_CURRENT_USER) • lm or hklm (HKEY_LOCAL_MACHINE). The case of key doesn’t matter.

  • Page 228: Launch Error Messages

    Launch Error Messages Launch displays a message if it encounters an error during the processing of a script. It is possible to get cascading error messages, as Launch does not stop processing the script if it encounters an error. An example of this would be a failure creating a directory causing the failure of all files copied to that directory.

  • Page 229: Example Script File

    Error Message Given by Description Shortcut Creation Failed error-code Shortcut There was a problem encountered creating the shortcut. Unable to open file script-file There was a problem opening the script-file. This message is only displayed when manually running Launch. Example Script File iffile,\System\applock.cab launchcmd,\Windows\wceload.exe,"/noaskdest /noui \System\applock.cab",w launch,\Windows\applockprep.exe,c...
  • Page 230 9 - 14...

  • Page 231: Chapter 10 - Enabler Installation And Configuration

    Doing so results in unnecessary delays when booting the device. The Avalanche Enabler installation file HSM_ENABLER_CAB is loaded on the MX9 by Honeywell; however, the device is not configured to launch the Enabler installation file automatically. The installation application must be run manually the first time Avalanche is used.

  • Page 232: Enabler Uninstall Process

    7. Reboot the MX9 if necessary. Update Monitoring Overview There are three methods by which the Enabler on the MX9 can communicate with the Mobile Device Server running on the host machine. • Wired via a serial cable between the Mobile Device Server PC and the MX9.

  • Page 233: Preparing A Device For Remote Management

    To configure the Avalanche Enabler management of the network and wireless settings: 1. Open the Enabler Settings Panels by tapping the Enabler icon on the desktop. 2. Select File > Settings. 3. Select the Adapters tab. 4. Choose settings for the Use Manual Settings parameter. 5.

  • Page 234: User Interface

    Enabler Configuration Depending on the version of the Enabler running on the MX9, the Enabler icon may look like one of the following: Enabler Settings Icon The Enabler user interface application is launched by clicking either the Enabler Settings icon on the desktop or Taskbar or by selecting Avalanche Enabler from the Programs menu.

  • Page 235: File Menu Options

    Avalanche Mobility Center User Guide for details. Settings The Settings option under the File menu allows the MX9 user to access the control panel to locally configure the Enabler settings. The Enabler control panel is, by default, password protected.

  • Page 236: Avalanche Update Using File > Settings

    Avalanche Update using File > Settings Use these menu options to setup the Avalanche Enabler on the MX9. Change the settings and then save the changes (reboot) before connecting to the network. Alternatively, the Mobile Device Server can be disabled until needed (refer to the Wavelink Avalanche Mobility Center User’s Guide for details).

  • Page 237: Connection

    Connection Avalanche Server Address Enter the IP Address or host name of the Mobile Device Server assigned to the MX9. Check Serial Connection Indicates whether the Enabler should first check for serial port connection to the Mobile Device Server before checking for a wireless connection to the Mobile Device Server.

  • Page 238: Execution

    Execution Note the dimmed options on this MX9 panel. This menu option is designed to manage downloaded applications for automatic execution upon startup. Auto-Execute Selection An application that has been installed with the Avalanche Management system can be run automatically following each boot.

  • Page 239: Data

    The Data tab controls when data is transferred between the MX9 and the Mobile Device Server. Transfer Data When Device is Idle When enabled, periodic updates from the Mobile Device Server are postponed until the MX9 has been idle for the specified period of time. The default is disabled.

  • Page 240: Preferences

    Application Startup Behavior of the Enabler when the MX9 boots up. The default is Monitor for Updates. • Do not Monitor - When the device boots, do not launch the Enabler application and do not attempt to connect to the Mobile Device Server.

  • Page 241: Taskbar

    • Basic Output - General information is displayed. • Critical - Critical errors are displayed in addition to those above. • Error - Communication or configuration problems are displayed in addition to those above. • Warning - Possible operation problems are displayed in addition to those above. •...

  • Page 242: Scan Config

    For best results use eXpress Config and eXpress Scan for this function. eXpress Scan is included with the updated MX9 enablers. Scan Config functionality is a standard option of the Wavelink Avalanche MC system but is not currently supported on the MX9.

  • Page 243: Display

    Display The user interface for the Enabler can be configured to dynamically change based on the status of the MX9 connection with the Mobile Device Server. At startup Default is Half Screen. Options are Half screen, Hidden or Full screen.

  • Page 244: Shortcuts

    For best results use AppLock for this function. AppLock is resident on each mobile device. Configure shortcuts to other applications on the MX9. Shortcuts are viewed and activated in the Programs panel. This limits the user’s access to certain applications when the Enabler is controlling the mobile device display.

  • Page 245: Saas

    SaaS Use to configure the Enabler to connect with Avalanche on Demand. This is a Software-as-a-Service version of Ava- lanche. Using either of the SaaS configuration options below assumes the user has registered with Wavelink. Disable SaaS No SaaS connection is used. Scan Configure SaaS Scan bar codes printed from within the Avalanche Console to configure the Enabler for the SaaS connection.

  • Page 246: Adapters

    Current Adapter Lists all network adapters currently installed on the MX9. Primary Adapter Indicates if the Enabler is to attempt to configure the primary adapter (active only if there are multiple network adapt- ers).
  • Page 247 Manual Settings Properties) Do not enable Manage Wireless Settings for Summit Client devices. Note: When you download a profile that is configured to manage network and wireless settings, the Enabler will not apply the manage network and wireless settings to the adapter unless the global Manage wireless settings and Manage network settings options are enabled on the Adapters panel.

  • Page 248: Status

    It also searches for new adapters and may cause a slight delay to refresh the contents of the drop-down menu. Link speed indicates the speed at which the signal is being sent from the adapter to the MX9. Speed is dependent on signal strength.

  • Page 249: Exit

    The Exit option is password protected. The default password is leave. The password is not case-sensitive. If changes were made on the MX9 Startup/Shutdown tab screen, then after entering the password, tap OK and the fol- lowing screen is displayed: Change the option if desired.

  • Page 250: Using Remote Management

    Scan Desktop Icon If the MX9 has an eXpress Scan icon on the desktop, eXpress Scan may be used for the initial configuration of the device. If the eXpress Scan icon is not present on the desktop, install the Enabler. If the icon is still not present, the Enabler must be updated.
  • Page 251 3. Click Start. 4. Bar code 1 must be scanned first. The scanned data is displayed in the “Data” text box. The password, if any, entered above is compared to the password entered when the bar codes were created. 5. If the passwords match, the bar code data is processed and the screen is updated to reflect the number of bar codes included in the set.

  • Page 252: Process Complete

    Process Complete After the last bar code is scanned, the settings are automatically applied. Once configured, the MX9 is warmbooted. Once connected to the wireless network and the Mobile Device Server, any soft- ware updates and additional configuration data are downloaded.

  • Page 253: Chapter 11 - Wireless Network Configuration

    Summit Client Utility Note: When making changes to profile or global parameters, tap the power key to place the MX9 in Suspend. When the MX9 resumes from suspend the parameters are applied. The MX9 can be resumed by tapping the power key or the touch screen or by pressing any key.

  • Page 254: Summit Tray Icon

    Summit Tray Icon The Summit tray icon provides access to the SCU and is a visual indicator of radio status. The Summit tray icon is displayed when: • The Summit radio is installed and active • The Windows Zero Config utility is not active •...

  • Page 255: Create A New Network Connection

    Create a New Network Connection 1. Tap on the Wi-Fi icon. A list of available networks is displayed. 2. If the desired network is not displayed, tap Add New. If the desired network is displayed in the list, tap the network name.

  • Page 256: Edit A Network Connection

    SSID. 4. In the Connects to box, select The Internet if the MX9 connects directly to the Internet, select Work if the MX9 con- nects to a network (even if the network provides an Internet connection).

  • Page 257: Main Tab

    Main Tab Setting Default Admin Login SUMMIT Radio Enabled Active Config/Profile Default Regulatory Domain Varies by location The Main tab displays information about the wireless client device including: • SCU (Summit Client Utility) version. • Driver version. • Radio Type (BG is an 802.11 b/g radio, ABG is an 802.11 a/b/g radio). •...

  • Page 258: Admin Login

    The Auto Profile selection screen displays all currently configured profiles. Tap on the check box for any profiles that are to be included in Auto Profile selection then tap ok to save. To enable Auto Profile, tap the On button on the Main tab. When Auto Profile is On, if the radio goes out of range from the currently selected profile, the radio then begins to attempt to connect to the profiles listed under Auto Profile.
  • Page 259 • View radio status, software versions and regulatory domain on the Main tab. • Access additional troubleshooting features on the Diags Tab (page 11-13). After Admin Login, the end-user can also: • Create, edit, rename and delete profiles on the Profile tab. •...

  • Page 260: Profile Tab

    Profile Tab Note: Tap the Commit button to save changes before leaving this panel or the SCU. If the panel is exited before tapping the Commit button, changes are not saved! Setting Default Profile Default SSID Blank Client Name Blank Power Save Fast Tx Power...
  • Page 261 Allows entry of WEP keys or pass phrase as required by the type of encryption. Credentials Button Allows entry of a user name and password, certificate names, and other information required to authenticate with the access point. The information required depends on the EAP type. Commit Button Saves the profile settings made on this screen.

  • Page 262: Profile Parameters

    WPA PSK, WPA TKIP, WPA CCKM, WPA2 PSK, WPA2 AES, or WPA2 CCKM. CKIP is not supported in the MX9. Note: The Encryption type chosen determines if the WEP Keys / PSK Keys button is active and also determines the available entries in the WEP or PSK pop-up window.
  • Page 263 It is important the Radio Mode parameter correspond to the Access Point (AP) to which the device is to connect. For example, if this parameter is set to G rates only, the MX9 may only connect to APs set for G rates and not those set for B and G rates.

  • Page 264: Status Tab

    Status Tab This screen provides information on the radio: • The profile being used. • The status of the radio card (down, associated, authenticated, etc.). • Client information including device name, IP address and MAC address. • Information about the Access Point (AP) maintaining the connection to the network including AP name, IP address and MAC address.

  • Page 265: Diags Tab

    Diags Tab The Diags screen can be used for troubleshooting network traffic and radio connectivity issues. (Re)connect Button Use this button to apply (or reapply) the current profile and attempt to associate or authenticate to the wireless LAN. All activity is logged in the Diagnostic Output box on the lower part of the screen. Release/Renew Button Obtain a new IP address through release and renew.

  • Page 266: Global Tab

    Global Tab The parameters on this panel can only be changed when an Admin is loggin in. The current values for the parameters can be viewed by the general user without requiring a password. Note: Tap the Commit button to save changes. If the panel is closed before tapping the Commit button, changes are not saved! Setting Default...

  • Page 267: Custom Parameter Option

    Custom Parameter Option Honeywell does not support the property Custom option. The parameter value is displayed as “Custom” when the operating system registry has been edited to set the Summit parameter to a value that is not available from the param- eter’s drop down list.
  • Page 268 Parameter Default Function Ad Hoc Channel Use this parameter when the Radio Mode profile parameter is set to Ad Hoc. Specifies the channel to be used for an Ad Hoc connection to another client device. If a channel is selected that is not supported by the by the radio, the default value is used.
  • Page 269 Parameter Default Function TX Diversity BG: On How to handle antenna diversity when transmitting packets to the Access A: Main Point. Only Options are: Main only (use the main antenna only), Aux only (use the auxiliary antenna only), or On (use diversity or both antennas). TX Diversity option should be set based on the antenna configuration as follows: •...
  • Page 270 Parameter Default Function Auth Timeout 8 seconds Specifies the number of seconds the Summit software waits for an EAP authentication request to succeed or fail. If the authentication credentials are stored in the active profile and the authentication times out, the association fails. No error message or prompting for corrected credentials is displayed.

  • Page 271: Sign-On Vs. Stored Credentials

    Sign-On vs. Stored Credentials When using wireless security that requires a user name and password, the Summit Client Utility offers these choices: • The User name and Password may be entered on the Credentials screen. If this method is selected, anyone using the device can access the network.
  • Page 272 10. Verify the device is authenticated by reviewing the Status tab. When the device is property configured, the Status Tab (page 11-12) indicates the device is Authenticated and the method used. 11. The sign-on screen is displayed after a reboot. Note: See Configuring Profiles (page 11-23) for more details.

  • Page 273: Windows Certificate Store Vs. Certs Path

    Windows Certificate Store vs. Certs Path Note: It is important that all dates are correct on the MX9 and host computers when using any type of certificate. Certificates are date sensitive and if the date is not correct authentication will fail.
  • Page 274 6. Tap to uncheck (and disable) the Use full trusted store check box. 7. Select the desired certificate and tap the Select button to return the selected certificate to the CA Cert text box. 8. Tap OK to exit the Credentials screen and then tap Commit to save the profile changes. 11 - 22...

  • Page 275: Configuring Profiles

    Configuring Profiles Use the instructions in this section to complete the entries on the Profile tab according to the type of wireless security used by your network. The instructions that follow are the minimum required to successfully connect to a network. Your system may require more parameters than are listed in these instructions.

  • Page 276: Wep

    To connect using WEP, make sure the following profile options are used. 1. Enter the SSID of the Access Point assigned to this profile. 2. Set EAP Type to None. 3. Set Encryption to WEP or Manual WEP (depending on SCU version). 4.

  • Page 277: Leap

    LEAP To use LEAP (without WPA), make sure the following profile options are used. 1. Enter the SSID of the Access Point assigned to this profile. 2. Set EAP Type to LEAP. 3. Set Encryption to WEP EAP or Auto WEP (depending on SCU version). 4.
  • Page 278 8. Enter the password. Tap OK then tap the Commit button. 9. Ensure the correct Active Profile is selected on the Main tab and Warmboot. The SCU Main tab shows the device is associated after the radio connects to the network. 11 - 26...

  • Page 279: Peap/Mschap

    PEAP/MSCHAP Note: The date must be properly set on the device to authenticate a certificate. To use PEAP/MSCHAP, make sure the following profile options are used. 1. Enter the SSID of the Access Point assigned to this profile. 2. Set EAP Type to PEAP-MSCHAP. 3.
  • Page 280 9. Enter the Domain\User name (if the Domain is required), otherwise enter the User name. 10. Enter the password. 11. Leave the CA Certificate File Name blank for now. 12. Tap OK then tap Commit. Ensure the correct Active profile is selected on the Main Tab. 13.

  • Page 281: Peap/Gtc

    PEAP/GTC To use PEAP/GTC, make sure the following profile options are used. 1. Enter the SSID of the Access Point assigned to this profile. 2. Set EAP Type to PEAP-GTC. 3. Set Encryption to WPA TKIP. 4. Set Auth Type to Open. 5.
  • Page 282 12. Tap OK then tap Commit. Ensure the correct Active Profile is selected on the Main Tab. 13. See Windows Certificate Store vs. Certs Path (page 11-21) for more information on certificate storage. 14. Once successfully authenticated, import the CA certificate into the Windows certificate store. 15.

  • Page 283: Wpa/Leap

    WPA/LEAP To use WPA/LEAP, make sure the following profile options are used. 1. Enter the SSID of the Access Point assigned to this profile. 2. Set EAP Type to LEAP. 3. Set Encryption to WPA TKIP. 4. Set Auth Type as follows: •...
  • Page 284 9. Enter the password. 10. Tap OK then tap the Commit button. 11. Ensure the correct Active Profile is selected on the Main Tab and Warmboot. The SCU Main tab shows the device is associated after the radio connects to the network. 11 - 32...

  • Page 285: Eap-Fast

    RADIUS server must have auto provisioning enabled to send the PAC provisioning credentials to the MX9. For automatic PAC provisioning, once a username/password is authenticated, the PAC information is stored on the MX9. The same username/password must be used to authenticate each time. See the note below for more details.
  • Page 286 8. To use Stored Credentials, tap on the Credentials button. No entries are necessary for Sign-On Credentials with automatic PAC provisioning as the user will be prompted for the User name and Password when connecting to the network. 9. To use Sign-On credentials: •...

  • Page 287: Eap-Tls

    EAP-TLS To use EAP-TLS, make sure the following profile options are used. 1. Enter the SSID of the Access Point assigned to this profile. 2. Set EAP Type to EAP-TLS. 3. Set Encryption to WPA TKIP. 4. Set Auth Type to Open. 5.
  • Page 288 Tap OK then tap Commit. The MX9 should be authenticating the server certificate and using EAP-TLS for the user authentication. Ensure the correct Active Profile is selected on the Main tab and Wamboot. The SCU Main tab shows the device is associ- ated after the radio connects to the network.

  • Page 289: Wpa Psk

    WPA PSK To connect using WPA/PSK, make sure the following profile options are used: 1. Enter the SSID of the Access Point assigned to this profile. 2. Set EAP Type to None. 3. Set Encryption to WPA PSK or WPA2 PSK. 4.

  • Page 290: Certificates

    Note: Refer to the Security Primer (available at www.honeywellaidc.com) to prepare the Authentication Server and Access Point for communication. Note: It is important that all dates are correct on the MX9 and host computers when using any type of certificate. Certificates are date sensitive and if the date is not correct authentication will fail.
  • Page 291 3. Tap the Download a CA certificate, certificate chain or CRL link. 4. Make sure the correct root CA certificate is selected in the list box. 11 - 39...
  • Page 292 5. Tap the DER button. 6. To download the CA certificate, tap on the Download CA certificate link. 7. Tap the Save button and save the certificate. Make sure to keep track of the name and location of the certificate. 11 - 40...

  • Page 293: Installing A Root Ca Certificate

    \System folder or other path specified in the Summit Certs global parameter. 1. Copy the certificate file to the MX9. The certificate file has a .CER extension. Locate the file and tap it. 2. A certificate installation warning text box is displayed: Your device is being asked to install a security certificate.
  • Page 294 4. Tap the Request a certificate link. 5. Tap on the User Certificate link. 11 - 42...

  • Page 295: Exporting A User Certificate

    6. Tap on the Submit button. If there is a message box asking if you want to confirm the request, tap Yes. 7. The User Certificate is issued. 8. Install the user certificate on the requesting computer by clicking the Install this certificate link. 9.

  • Page 296: Installing A User Certificate

    12. Install the user certificate. Installing a User Certificate 1. After generating and exporting the user certificate, copy it from the PC to the MX9. Copy the certificate to a location on the MX9, such as a storage card or the \System folder.

  • Page 297: Chapter 12 - Keymaps

    62-Key Keypad KeyMap The following keymap is used on an MX9 that is not running a Terminal Emulator. Terminal emulators use a separate keymap. A modifier key pressed after itself toggles that modifier key off.
  • Page 298 To get this function Press these keys in this order Result / Notes Alt mode Alt mode Ctl mode Control mode Escape Escape Space Space Enter Enter Enter Capslock toggle Blue Capslock is on or off Mapped Diamond 1 Key Diamond 1 Use the Keymap Control Panel to change default...
  • Page 299 To get this function Press these keys in this order Result / Notes Blue F20 mode SHFT F21 mode SHFT F22 mode SHFT F23 mode SHFT F24 mode a (lowercase is the default) SHFT SHFT SHFT SHFT SHFT SHFT SHFT SHFT SHFT SHFT...
  • Page 300 To get this function Press these keys in this order Result / Notes SHFT SHFT SHFT SHFT SHFT SHFT SHFT SHFT SHFT SHFT SHFT SHFT SHFT 0 (zero) 0 (zero) . (period) Orange Period . (period) Orange Period Blue Dash or minus sign Blue Reverse Solidus or Backslash Orange...
  • Page 301 To get this function Press these keys in this order Result / Notes SHFT 5 (number) Percent sign Orange Caret or circumflex SHFT 6 (number) Caret or circumflex & Orange Ampersand & SHFT 7 (number) Ampersand Orange I (alpha i) Asterisk SHFT 8 (number)

  • Page 302: 62-Key 5250 Keypad Overlay Keymap

    62-Key 5250 Keypad Overlay KeyMap ENTER Attn > < Fld+ Fld- E-Inp sReq & Caps SHFT To get this function Press these keys in this order Result / Notes Attention (Attn) 5250 Attn Clear (Clr) 5250 Clr Delete (Del) 5250 Del Duplicate (Dup) 5250 Dup Erase Input (E-Inp)
  • Page 303 To get this function Press these keys in this order Result / Notes Ctl mode Control mode Escape Escape Space Space Enter Enter Enter Capslock toggle Blue Capslock is on or off Mapped Diamond 1 Key Diamond 1 Use the Keymap Control Panel to change default Mapped Diamond 2 Key Blue...
  • Page 304 To get this function Press these keys in this order Result / Notes Blue F20 mode SHFT F21 mode SHFT F22 mode SHFT F23 mode SHFT F24 mode a (lowercase is the default) SHFT SHFT SHFT SHFT SHFT SHFT SHFT SHFT SHFT SHFT...
  • Page 305 To get this function Press these keys in this order Result / Notes SHFT SHFT SHFT SHFT SHFT SHFT SHFT SHFT SHFT SHFT SHFT SHFT SHFT SHFT 0 (zero) 0 (zero) . (period) Orange Period . (period) Orange Period Blue Dash or minus sign Blue Reverse Solidus or Backslash...
  • Page 306 To get this function Press these keys in this order Result / Notes Orange Percent sign SHFT 5 (number) Percent sign Orange Caret or circumflex SHFT 6 (number) Caret or circumflex & Orange Ampersand & SHFT 7 (number) Ampersand Orange I (alpha i) Asterisk SHFT...

  • Page 307: 38-Key Keypad Keymap

    38-key Keypad KeyMap The following keymap is used on an MX9 that is not running a Terminal Emulator. Terminal emulators use a separate keymap. A modifier key pressed after itself toggles that modifier key off. Any key press, other than a modifier key following any modifier key unsticks the modifier keys.
  • Page 308 To get this function Press these keys in this order Result / Notes Backtab Orange Backtab Cursor Up Up Arrow Cursor up one line Cursor Down Down Arrow Cursor down one line Cursor Right Blue Up Arrow Cursor right one space Cursor Left Blue Down Arrow...
  • Page 309 To get this function Press these keys in this order Result / Notes Alpha Alpha Alpha Alpha Alpha Alpha Alpha Alpha Alpha Alpha 7777 Alpha Alpha Alpha Alpha Alpha Alpha Alpha 9999 SHFT Alpha SHFT Alpha SHFT Alpha SHFT Alpha SHFT Alpha SHFT...
  • Page 310 To get this function Press these keys in this order Result / Notes 0 (zero) 0 (zero) . (period) Orange Period Blue Dash or minus sign Blue Reverse Solidus or Backslash Orange Solidus or Forward slash Orange Left square bracket Blue Left square bracket Orange...
  • Page 311 To get this function Press these keys in this order Result / Notes Blue Tilde < Blue Less than mark > Blue More than mark Orange 0 (zero) Colon Blue BKSP Plus sign (Backspace) Orange Question mark Orange Underscore or horizontal bar 12 - 15...
  • Page 312 12 - 16...

  • Page 313: Unpacking Your Battery Charger

    This device cannot charge/recharge coin cell batteries sealed inside the mobile device, if any. This chapter is intended to familiarize the user with the safety and operating instructions necessary to use the MX9 Battery Charger (Model MX9385CHARGER, MX9384CHARGER) to charge rechargeable lithium-ion battery packs (MX9380BATTERY, MX9381BATTERY).

  • Page 314: Lithium-Ion Battery Pack

    • Do not store the Li-Ion battery pack in direct sunlight or anywhere the battery pack cannot cool down. • If the Li-Ion battery pack is hot after removal from the MX9, allow it to cool at room temperature or in a cool air stream before placing it in the charger.

  • Page 315: Front View

    5. AC Power port Installation Assemble the Power Supply Assemble the AC adapter for the MX9 Battery Charger before connecting it to the charger. The AC power supply for the battery charger is shipped with the battery charger. Contact Customer Support (page 16-1) if there is no AC cable.

  • Page 316: Setup

    Setup Place the battery charger on a flat, horizontal, hard surface or fasten securely to a stable surface using the keyhole open- ings on the bottom of the battery charger. See Mounting. Do not insert battery packs until the battery charger has finished powering up: 1.

  • Page 317: Inserting A Battery Into The Charging Pocket

    Inserting a Battery into the Charging Pocket It is important that battery packs are inserted into the charging pocket correctly. Inserting the battery incorrectly could result in damage to the battery pack or the charger. Do not “slam” the battery pack into the charging pocket. Damage may result. 1.

  • Page 318: Battery Charger Help

    Issue Cause Solution Battery pack does not fit in charging Different manufacturer's battery Check if the MX9 battery pack has pocket. pack, or there is an object in the Honeywell part number MX9380BATT or charging pocket. MX9381BATT (Low Temperature) on the label.

  • Page 319: Charger Cleaning, Storage And Service

    Issue Cause Solution LED is flashing RED at any pocket. The battery pack voltage has not Contact Customer Support (page 16-1) for reached 6.0V within 30 minutes battery pack replacement options. and the charger has timed out.The battery pack voltage has not reached 2.5V within 60 minutes and the charger has timed out.

  • Page 320: Service

    Do not store battery packs in direct sunlight, on a metal surface, or anywhere the battery pack cannot cool down. Do not leave the battery pack in a non-operating charger. The battery pack may discharge through the charger rather than hold its charge.

  • Page 321: Chapter 14 - Cradles

    Bluetooth device connection and use, while the MX9 is docked, are managed by the MX9 Bluetooth program, not the cradle. The MX9 can be either On, Off or in Suspend Mode while in the cradle. Special purpose and power cables are available from Honeywell.

  • Page 322: Tethered Scanners And The Mx9 Cradles

    Use a clean soft cloth to wipe any dirt, moisture or grease from the MX9, charging contacts or the cradle. Do not use any liquid to clean the cradle, battery pack, MX9, or charging terminals (pins). Spray or dampen the cleaning cloth with liquids/sprays. If possible, clean only those areas which are soiled.

  • Page 323: Battery Cleaning, Storage And Service

    Main battery recharging in a docked MX9 is managed by the Power Management settings in the MX9. Refer to the Power control panel on the MX9. The spare battery in the spare battery well re-charges with or without an MX9 in the dock. The spare battery is fully charged in approximately four hours.

  • Page 324: Front View

    3. AC/DC Power port 4. Serial port 5. Ethernet port 6. USB Client port 7. USB Host port Side View 1. Front / MX9 Docking/Charging Bay 2. Spare Battery Charging Bay 3. Back / Power port 4. Table Mounting Holes 14 - 4...

  • Page 325: Top View

    3. Back Not to Scale Bolts, washers, screws, screwdriver or wrench needed when attaching the MX9 desktop cradle to a protected flat surface are not supplied by Honeywell. Periodically check the table mounting hardware and re-tighten if necessary. Table mounting hardware can be finger-tight- ened.

  • Page 326: Assemble/Attach The Ac Power Adapter

    Note: Route all cables to ensure they are protected from jostling, tugging or being disconnected by passing objects. The cradle must be receiving power from an external power source before MX9 battery charging can begin. Note: Periodically test the connections for stability and adjust as necessary.

  • Page 327: Desktop Cradle Connector Identifiers

    Test the connection for stability. Connecting a USB Host and USB Client Cable Firmly press the cable end into the MX9 USB Client (5) or USB Host (6) Port connector on the back of the cradle. Test the connections for stability.

  • Page 328: Spare Battery Led

    Docking and Undocking the MX9 When the MX9 is in Suspend Mode it wakes up when it is docked in a powered cradle. There is no change in mode state settings or behavior when the MX9 is docked in a cradle without a power source.

  • Page 329: Inserting A Spare Battery

    The spare battery charger can recover a battery that has had its safety circuit tripped. The spare battery well is molded in the shape of the MX9 main battery. The spare battery can be inserted in the battery well in only one direction. When there is an MX9, with or without a handle, docked in the cradle, a spare battery can still be inserted in the charging bay.
  • Page 330 However, depending on the temperature of the MX9 battery, it may take 2-3 hours to adjust. The battery pack can cool down faster if the battery is not in the battery well.

  • Page 331: Using A Powered Vehicle Cradle

    Never put the MX9 into the vehicle mounted assembly until the assembly is securely fastened to the vehicle. The MX9 must have a main battery installed when it is docked in a vehicle mounted cradle. The main battery in the MX9 is recharged when the MX9 is docked in a powered vehicle cradle.

  • Page 332: Components

    Components Before installation begins, verify you have the applicable vehicle mounting bracket assembly components necessary for your mount type. Front View 1. Docking Guide Pin (left) 2. Release Latch (left) 3. Docking Bay 4. Charge/Communicate port 5. Power LED Back View 1.

  • Page 333: Ram Bracket Mounting

    The figure shown below is an example RAM ball mounting screws are included in the mounting kit. Contact Technical Assistance (page 16-1) for the MX9 RAM Mount Kit for the vehicle cradle. RAM Bracket Mounting Points 1. RAM ball mounted on the back of the vehi- cle cradle 2.

  • Page 334: Vehicle Cradle Ram Ball Assembly

    Periodically test the mounting device and re-tighten bolts, RAM balls and/or squeeze arm adjustment knob as needed. RAM Circular Base Footprint Bolts, washers and nuts for mounting the RAM ball to the vehicle are supplied by Honeywell: • Qty 4 – Hex Cap 1/4-20 x 3/4 bolts •...

  • Page 335: Dc/Dc Power Supply Installation, Screws On Side Of Lid

    DC/DC Power Supply Installation, Screws on Top of (page 14-18) for installation instruction. Connecting Electrical Cables to Power Sources The DC/DC power supply is used to provide vehicle power to the MX9 when it is placed in a DC powered vehicle cradle. Specifications for Electrical Supply Input Voltage Always observe input voltage range specified for the DC/DC power supply.

  • Page 336: Wiring Schematic

    Warning: Risk of ignition or explosion. Explosive gas mixture may be vented from battery. Work only in well ventilated area. Avoid creating arcs and sparks at battery terminals. Wiring Schematic Connecting to Vehicle Power The vehicle cradle must be empty. The last connection must be to the vehicle power source. 1.
  • Page 337 6. Attach the stripped wire ends to the output side of the DC/DC power supply. Note: The input block has V and GND terminals. The output block has V and V terminals. 7. Connect the ground wire from the cradle to the GND terminal on the input side of the DC/DC power supply. 8.

  • Page 338: Dc/Dc Power Supply Installation, Screws On Top Of Lid

    (page 14-15) for installation instruction. Connecting Electrical Cables to Power Sources The DC to DC power supply is used to provide vehicle power to the MX9 when placed in a DC powered vehicle cradle. Specifications for Electrical Supply Input Voltage Always observe input voltage range specified on the DC to DC power supply.

  • Page 339: Wiring Schematic

    Wiring Schematic Connecting Vehicle Electrical Supply 1. The vehicle cradle must be empty. 2. Begin by connecting the power cable to the vehicle cradle. Work from this connection with the last connection being to the vehicle’s power source. 3. Route the cable from the cradle to the DC to DC power supply. 4.
  • Page 340 9. Wire colors depend on the type of device attached. Please refer to the Wiring Schematic for wire colors. 10. Use the looms and wire ties to secure all wiring as shown above, then reattach the lid. 11. Connect the DC to DC power supply to the vehicle’s electrical system as directed below:. Caution: For battery powered vehicles: + is connected to battery positive.

  • Page 341: Vehicle 12V Bare Wire Adapter

    Vehicle 12V Bare Wire Adapter Part Number: 9000A079CBL12ML3 Caution: For proper and safe installation, the input power cable must be connected to a fused circuit on the vehicle. This fused circuit requires a ten Amp maximum time delay (slow blow) high interrupting rating fuse. If the supply connection is made directly to the battery, the fuse should be installed in the positive lead within 5 inches of the battery positive (+) terminal.

  • Page 342: Connecting Vehicle 12 Vdc Supply

    Vehicle Cradle Strain Relief Cable Clamp (page 14-23). 4. The power LED on the MX9 illuminates when it is receiving external power and the MX9 is docked. Attaching a Serial or I/O Connector The serial cable can originate with a tethered scanner, a desktop/laptop PC, a printer or another serial device.

  • Page 343: I/O Port

    (page 14-23). Vehicle Cradle Strain Relief Cable Clamp Equipment Required: Phillips screwdriver (not supplied by Honeywell) There are two strain relief cable clamps secured to the back of the vehicle cradle. They are located at the back of the cradle, below the trigger handle opening.

  • Page 344: Vehicle Cradle Led

    Note: Do not put the MX9 into the vehicle cradle until the cradle is securely fastened to the vehicle. 1. The MX9 is docked in the vehicle cradle by sliding the base of the MX9 down into the cradle docking bay until the con- nector at the base of the MX9 clicks into place with the charging/communication connector at the bottom of the docking bay.

  • Page 345: Removing The Mx9 From The Mounted Vehicle Cradle

    Removing the MX9 from the Mounted Vehicle Cradle 1. Place one hand on the MX9 and press one of the release latches (located on either side of the cradle docking bay). 2. The MX9 disconnects from the cradle pins and springs forward.
  • Page 346 14 - 26...

  • Page 347: Chapter 15 - Technical Specifications

    One SD port for I/O expansion (capable) One SIM port for WAN One serial port (DTE) for interface with GPS receiver chip One camera port for non-decoding imager MX9 Dimensions and Weight. Length (overall) 9.94 in / 25.2 cm Width at Display 3.87 in / 9.8 cm...

  • Page 348: Mx9 Environmental Specifications

    For 5 GHz frequency band, the site survey limit is -65 dBm signal strength, 15 dB SNR as measured by Honeywell. The noise levels for each of the radios (as measured by the MX9 appropriate antenna) is less than or equal to the values...

  • Page 349: Bluetooth System Compatibility

    Serial Interface The GPS module supports serial interface for data communication. Transmission (TX) and Reception (RX) signals are implemented to send commands and to receive GPS data. Honeywell designs use UART B on the module for communica- tion. The default baud rate for the NMEA 0183 protocol is 9600 bps, 8 bits, Parity None, 1 Stop. The baud rate can be increased to 115Kbps.

  • Page 350: Desktop And Vehicle Cradle Pinout - Rs232 Connector

    Accuracy Position to within 10 meters, 2D Root Mean Square (RMS) and 5 meters 2D RMS, Satellite Based Augmentation System (SBAS) corrected. Velocity to within 24 meters per second. SBAS is compatible with the Wide Area Augmentation System (WAAS) satellite signal augmenter (United States) and the EGNOS satellite signal augmenter (Europe).

  • Page 351: Desktop Cradle Technical Specifications

    Note: Battery packs may leak up to 1mA current through the battery contacts when left in an unpowered battery charger charging pocket. Do not store MX9 batteries above 140°F (60°C) for extended periods. Standard Battery: Li-Ion 3.9A 2400mAh battery with a 500 charge/discharge life cycle.

  • Page 352: Dimensions

    Dimensions Weight 3 lb 10 oz / 1.6 kg (with a battery in each charging bay 2 lb 0 oz / 0.9 kg (no batteries) Length 16” / 40 cm Width 5.75” / 14.6 cm Height 1.5” / 4 cm Plug Type IEC320 (3 prong, grounded) / barrel connector Mounting...

  • Page 353: Chapter 16 - Customer Support

    Limited Warranty Honeywell International Inc. (“HII”) warrants its products to be free from defects in materials and workmanship and to conform to HII’s published specifications applicable to the products purchased at the time of shipment. This warranty does not cover any HII product which is (i) improperly installed or used;...
  • Page 354 The duration of the limited warranty for the MX9 Battery Charger is 1 year. The duration of the limited warranty for the MX9 2400mAh Li-Ion and 2100mAh Li-Ion Battery is 6 months. The duration of the limited warranty for the MX9 AC power supply and cables is 1 year.
  • Page 355 Back Cvr - 1...
  • Page 356 Honeywell Scanning & Mobility 9680 Old Bailes Road Fort Mill, SC 29707 www.honeywellaidc.com ™ MX9-WM-UG Rev A 6/14...

Table of Contents