Table of Contents
Advertisement
29
19
8
DETAIL
A
29
19
DETAIL
B
10
25
2 PL
20
26
3
DETAIL
C
11
25
2 PL
20
26
3
DETAIL
D
4 TO ASSEMBLE LOWER TRAY, USE 2 LOWER
LIGHT BLOCK GUIDES (ITEM NO. 5) IN PLACE
OF ITEMS NO. 21 & 22. SEE DRAWING.
3 APPLY LOCTITE (82ADH04) TO THREADS
WHERE INDICATED.
2. PLACE MYLAR FRAME ASSEMBLY (ITEM 3) ATOP
GLASS FRAME ASSEMBLY (ITEM 2) AND TRAY
WELDMENT (ITEM 1). ASSEMBLE AS SHOWN.
10-4
Tray Assembly Drawing (cont.)
50
2
49
161"
48
2
47
5
1
46
12
45
10
44
1
43
1
42
6
41
2
40
39
8
38
18
37
18
36
2
35
2
9
34
8
33
32
28
31
6
9
13
30
29
2
1
28
1
27
26
2
2
25
1
24
1
23
1
22
1
21
2
20
19
2
1
18
17
1
16
6
2
15
2
14
4
13
12
3
1
11
10
1
9
1
8
1
7
1
6
2
5
2
4
4
3
1
2
1
1
1
QTY
GAS SPRING (80 LBS)
ADHESIVE RUBBER GASKET
HINGE BLOCK CLAMP
NSI CABLE TIE, UV, 4"
CABLE, MAGNETIC TRAY SWITCH
NSI 6-32 X 1/2 PHIL PAN BLK
NSI #6 KEP NUT ZINC
RAMP SWITCHES, AP30/OV33
1/4-20 X 3/8 BOTTON HEAD
NSI 10-32 X 3/8 PPMS BLK
NSI LOCKWASHER SPLIT 1/4"
10-32 X 3/4 SHCS
NSI #10 FLAT WASHER BLACK
NSI #10 LOCKWASHER SPLIT
5/16-18 HEX NUTS BLK ZINC
NSI 1/4 - 20 X 1 SKT HD CAP
1/4-20 X 5/8 SKT BTN HD SCREW
NSI #6 SPLIT LOCK WASHER
NSI #6 FLAT WASHER, BLACK ZINC
NSI 6-32 X 3/8 PHIL PAN MS BLK
NSI 10-32 X5/8 SOC HD CAP BLK
NSI 6-32 X 1/4 PHIL PAN MS BLK
NSI 8-32 X 3/16 PPMS BLK ZINC
WASHER, .380 ID .625
NSI SOCKET SHOULDER BOLT-
WASHER, NYLON, 3/8 X3/4 X1/16
PIVOT BAR, OV45
BRACKET, VACUUM HOSE OV45
GUIDE, LT. BLOCK (65SEAL)R.
GUIDE, LT. BLOCK (65SEAL)L.
WHEEL
LINEAR BEARING 1/2" DIA.
MOUNT, LIGHT BLOCK GIUDE
SWITCH, MAGNETIC INTE.
BALL STUD, MODIFIED
GAS SPRING 60 LBS.
BALL STUD MOUNT PLATE
HINGE, BLOCK
END PIVOT BLOCK
FRONT WHEEL BLOCK
REAR WHEEL BLOCK
FRONT BEARING BLOCK
REAR BEARING BLOCK
TIE WRAP ADHESIVE MOUNT BASE
HANDLE, 6", ALUM. BLACK
GIUDE, LIGHT BLOCK, LOWER
SOCKET HEAD, CAP SCREW
MYLAR FRAME ASSEMBLY
GLASS FRAME ASSEMBLY
WELDMENT, TRAY, OV42
DESCRIPTION
6 CUT TWO PIECES OF GASKET (ITEM 49) AT
37" LONG, AND TWO PIECES AT 43.25".
ASSEMBLE AS SHOWN.
5 CONNECT MAG. SWITCH CABLE (ITEM 46) TO SWITCH ON
WELDMENT (ITEM 1); ROUTE TOWARD REAR. SECURE WITH
FIVE CABLE TIES (ITEM 47), AND ONE TIE WRAP (ITEM 7).
BE SURE HARNESS DOES NOT COME IN CONTACT WITH ANY
SHARP EDGES ON WELDMENT.
43SPR24
SEE BOM
19D3815A02
44TIE08
16D2970A99
41BO6PPS.50
41-06NKP
11D2112A62
41-F0SHB.37
41B12PPS.37
41-F0WLS
41B12SHC.75
41B10WFR
41 10WLS
41BF2NHX
41BOSHC1.0
41BFOSHC.62
41-06WLS
41B06WFR
41B06PPS.37
41B12SHC.62
41B06PPS.25
41B08PPS.18
41WFR03
41BF2BHX.75
41HHS2679
12D1727B99
11D1696A02
11D2709B62
11D2709A62
43BLB17
43BLB12
12D1737A62
55SW50-B
43SDB03
43SPR25
43SDB03
19D3825A76
12D1895A99
12D1731A71
12D1733A00
12D1730A71
12D1732A71
44PAD03
44HDL05
11D2145A62
SEE BOM
91MYLFRM-AP42
91GLFRM-42
19D3826A02
PART NO.
94MS42 Rev.B1 S/W Ver 2.06
Advertisement
Table of Contents
