Canon iR2030 Series Service Manual page 315

No. Tx/Rx Description
##0282 [Tx] at time of transmission, the procedural signal has been transmitted more than specified.
##0283 [Tx] at time of transmission, the procedural signal has been transmitted more than specified.
##0284 [Tx] at time of transmission, DCN is received after transmission of TCF.
##0285 [Tx] at time of transmission, DCN is received after transmission of EOP.
##0286 [Tx] at time of transmission, DCN is received after transmission of EOM.
##0287 [Tx] at time of transmission DCN is received after transmission of MPS.
##0288 [Tx] after transmission of EOP, a signal other than PIN, PIP, MCF, RTP, or RTN has been received.
##0289 [Tx] after transmission of EOM, a signal other than PIN, PIP, MCF, RTP, or RTN has been received.
##0290 [Tx] after transmission of MPS, a signal other than PIN, PIP, MCF, RTP, or RTN has been received.
##0670 [Tx] at time of V.8 late start, the V.8 ability of DIS front the receiving party is expected to be detected, and the CI signal is expected
to be transmitted in response; however, the procedure fails to advance, and the line is released because of T1 time-out.
##0671 [Rx] at time of V.8 arrival, procedure fails to move to phase 2 after detection
releasing line
##0672 [Tx] at time of V.34 transmission, a shift in procedure from phase 2 to phase 3 and thereafter stops, causing the machine to release
the line and suffer T1 timeout.
##0673 [Rx] at time of V.34 reception, a shift in procedure from phase 2 to phase 3 and thereafter stops, causing the machine to release the
line and suffer T1 timeout.
##0674 [Tx] at time of V.34 transmission, a shift in procedure from phase 3 and phase 4 to the control channel and thereafter stops, causing
the machine to release the line and suffer T1 timeout.
##0675 [Rx] at time of V.34 reception, a shift in procedure from phase 3 and phase 4 to the control channel and thereafter stops, causing the
machine to release the line and suffer T1 timeout.
##0750 [Tx] at time of ECM transmission, no meaningful signal is received after transmission of PPS-NULL, causing the procedural signal
to be transmitted more than specified.
##0752 [Tx] at time of ECM transmission, DCN is received after transmission of PPS-NULL.
##0753 [Tx] at time of ECM transmission, the procedural signal has been transmitted more than specified after transmission of PPS-NULL,
or T5 time-out (60 sec) has occurred.
##0754 [Tx] at time of ECM transmission, the procedural signal has been transmitted more than specified after transmission of PPS-NULL.
##0755 [Tx] at time of ECM transmission, no meaningful signal is received after transmission of PPS-MPS, causing the procedural signal to
be transmitted more than specified.
##0757 [Tx] at time of ECM transmission, DCN is received after retransmission of PPS-MPS.
##0758 [Tx] at time of ECM transmission, the procedural signal has been transmitted more than specified after transmission of PPS-MPS, or
T5 time-out (60 sec) has occurred.
##0759 [Tx] at time of ECM transmission, the procedural signal has been transmitted more than specified after transmission of PPS-MPS.
##0760 [Tx] at time of ECM transmission, no meaningful signal is received after transmission of PPS-EOM, causing the procedural signal to
be transmitted more than specified.
##0762 [Tx] at time of ECM transmission, DCN is received after transmission of PPS-EOM.
##0763 [Tx] at time of ECM transmission, the procedural signal has been transmitted more than specified after transmission of PPS-MPS, or
T5 time-out (60 sec) has occurred.
##0764 [Tx] at time of ECM transmission, the procedural signal has been transmitted more than specified after transmission of PPS-EOM.
##0765 [Tx] at time of ECM transmission, no meaningful signal is received after transmission of PPS-EOP, causing the procedural signal to
be transmitted more than specified.
##0767 [Tx] at time of ECM transmission, DCN is received after transmission of PPS-EOP.
##0768 [Tx] at time of ECM transmission, the procedural signal has been transmitted more than specified after transmission of PPS-EOP, or
T5 time-out (60 sec) has occurred.
##0769 [Tx] at time of ECM transmission, the procedural signal has been transmitted more than specified after transmission of PPS-EOP.
##0770 [Tx] at time of ECM transmission, no meaningful signal is received after transmission of EOR-NULL, causing the procedural signal
to be transmitted more than specified.
##0772 [Tx] at time of ECM transmission, DCN is received after transmission of EOR-NULL.
##0773 [Tx] at time of ECM transmission, the procedural signal has been transmitted more than specified after transmission of EOR-NULL,
or T5 time-out (60 sec) has occurred.
##0774 [Tx] at time of ECM transmission, ERR is received after transmission of EOR-NULL.
##0775 [Tx] at time of ECM transmission, no meaningful signal is received after transmission of EOR-MPS, causing the procedural signal to
be transmitted more than specified.
##0777 [Tx] at time of ECM transmission, DCN is received after transmission of EOR-MPS.
##0778 [Tx] at time of ECM transmission, the procedural signal has been transmitted more than specified after transmission EOR-MPS, or
T5 time-out (60 sec) has occurred.
##0779 [Tx] at time of ECM transmission, ERR is received after transmission of EOR-MPS.
##0780 [Tx] at time of ECM transmission, no meaningful signal is received after transmission of EOR-EOM, causing the procedural signal
to be transmitted more than specified.
##0782 [Tx] at time of ECM transmission, DCN is received after transmission of EOR-EOM.
##0783 [Tx] at time of ECM transmission, the procedural signal has been transmitted more than specified after transmission of EOR-EOM,
or T5 time-out (60 sec) has occurred.
##0784 [Tx] at time of ECM transmission, ERR is received after transmission of EOR-EOM.
##0785 [Tx] at time of ECM transmission, no meaningful signal is received after transmission of EOR-EOP, causing the procedural signal to
be transmitted more than specified.
##0787 [Tx] at time of ECM transmission, DCN is received after transmission of EOR-EOP.
##0788 [Tx] at time of ECM transmission, the procedural signal has been transmitted more than specified after transmission of EOR-EOP, or
T5 time-out (60 sec) has occurred.
##0789 [Tx] at time of ECM transmission, ERR is received after transmission of EOR-EOP.
##0790 [Rx] at time of ECM reception, ERR is transmitted after transmission of EOR-Q.
##0791 [Tx/Rx] while ECM mode procedure is under way, a signal other than a meaningful signal is received.
##0792 [Rx] at time of ECM reception, PPS-NULL cannot be detected over partial page processing.
of CM signal from caller, causing T1 time-out and
Chapter 14
14-11