Canon iR2030 Series Service Manual page 17

15.4.7 <No.010 Frequency of the pseudo CI signal> ................................................................................................... 15- 18
15.5 Setting of Numeric Parameter (NUMERIC Param.)..............................................................................15- 18
15.5.1 Numerical Parameter Composition.................................................................................................................... 15- 18
15.5.2 <002: RTN transmission condition (1)><003: RTN transmission condition (2)><004: RTN transmission condition (3)>
15- 19
15.5.3 <005: NCC pause length (pre-ID code)> ........................................................................................................... 15- 19
15.5.4 <006: NCC pause length (post-ID code)> ......................................................................................................... 15- 19
15.5.5 <010: line connection identification length>....................................................................................................... 15- 19
15.5.6 <011: T.30 T1 timer (for reception)>.................................................................................................................. 15- 19
15.5.7 <013: T.30 EOL timer> ...................................................................................................................................... 15- 19
15.5.8 <016: time length to first response at time of fax/tel switchover> ...................................................................... 15- 20
15.5.9 <017: pseudo RBT signal pattern ON time length><018: pseudo RBT signal pattern OFF time length (short)><019:
pseudo RBT signal pattern OFF time length (long)> ............................................................................................... 15- 20
15.5.10 <020: pseudo CI signal pattern ON time length><021: pseudo CI signal pattern OFF time length (short)><022:
pseudo CI signal pattern OFF time length (long)>................................................................................................... 15- 20
15.5.11 <023: CNG detention level for fax/tel switchover>........................................................................................... 15- 20
15.5.12 <024: pseudo RBT transmission level at time of fax/tel switchover> ............................................................... 15- 20
15.5.13 <025: Answering machine connection function signal detection time>............................................................ 15- 20
15.5.14 <027: V.21 low-speed flag preamble identification length> ............................................................................. 15- 20
15.5.15 <055: Acquisition period of environmental log data> ....................................................................................... 15- 20
15.5.16 <056 - 061: Count type select >....................................................................................................................... 15- 20
15.6 Setting of Scanner Functions (SCANNER)...........................................................................................15- 23
15.6.1 Setting of Bit Switch........................................................................................................................................... 15- 23
15.6.2 Numeric Parameter Functional configuration .................................................................................................... 15- 24
15.6.3 <024:CIS scan position during ADF scanning> ................................................................................................. 15- 25
15.6.4 <026:Distance from the standby position of CIS to the shading start point> ..................................................... 15- 25
15.6.5 <031Vertical scan start position adjustment> .................................................................................................... 15- 25
15.6.6 <032Horizontal scan start position adjustment>................................................................................................ 15- 25
15.6.7 <033Vertical scan magnification correction> ..................................................................................................... 15- 25
15.6.8 <035: - 036:Reader motor speed change>........................................................................................................ 15- 25
15.6.9 <041: Vertical scan start position adjustment (when scanning on a document fed from ADF)> ....................... 15- 26
15.6.10 <042: Horizontal scan start position adjustment (when scanning on a document fed from ADF)> ................. 15- 26
15.6.11 <043: Horizontal scan end position correction ((copy:scanning on ADF)> ...................................................... 15- 26
15.6.12 <044: Horizontal scan end position correction (superfine:scanning on ADF)> ................................................ 15- 26
15.6.13 <045: Horizontal scan end position correction (fine:scanning on ADF)> ......................................................... 15- 26
15.6.14 <046: Horizontal scan end position correction (standard:scanning on ADF)> ................................................. 15- 26
15.6.15 <047: Vertical scan magnification correction (when scanning on a document fed from ADF)>....................... 15- 26
15.6.16 <048: Horizontal scan magnification correction (when scanning on a document fed from ADF)> .................. 15- 26
15.6.17 <193: ADF special standard-sized paper: LGL misidentification-ready> ......................................................... 15- 26
15.6.18 <194: ADF special standard-sized paper: LTR misidentification-ready> ......................................................... 15- 26
15.6.19 <195: ADF special standard-sized paper: LTR_R misidentification-ready> .................................................... 15- 26
15.6.20 <196: Shading Target Value (Red)> ................................................................................................................ 15- 27
15.6.21 <197: Shading Target Value (Green)>............................................................................................................. 15- 27
15.6.22 <198: Shading Target Value (Blue)> ............................................................................................................... 15- 27
15.6.23 <213: XYZ correction value (X) of standard white plate> (if equipped with SEND functions)) ........................ 15- 27
15.6.24 <214: XYZ correction value (Y) of standard white plate> (if equipped with SEND functions).......................... 15- 27
15.6.25 <215: XYZ correction value (Z) of standard white plate> (if equipped with SEND functions) .......................... 15- 27
15.7 Setting of Printer Functions (PRINTER) ...............................................................................................15- 28
15.7.1 Service Soft Switch Settings (PRINTER)........................................................................................................... 15- 28
15.7.1.1 SSSW-SW05...................................................................................................................................................................... 15- 28
15.7.1.2 SSSW-SW14...................................................................................................................................................................... 15- 28
15.7.1.3 SSSW-SW15...................................................................................................................................................................... 15- 29
15.7.1.4 SSSW-SW18...................................................................................................................................................................... 15- 30
15.7.2 Numerin Parameter Settings (Numeric Prama.) ................................................................................................ 15- 31
15.7.2.1 List of Functions ................................................................................................................................................................. 15- 31
15.7.2.2 <031: Top registration adjustment (manual feed tray)> ..................................................................................................... 15- 31
15.7.2.3 <032: Top registration adjustment (cassette)>................................................................................................................... 15- 31
Contents