BodyCraft K2 Instruction Manual page 12

STEP 5
1. Attach the Seat Frame (8) to the Front Upright (5), using two 3/8" X 3" Hex Bolts (131), four 3/8" Washers
(152) and two 3/8" Nuts (159). Attach the Seat Frame (8) to the Base Frame (1) using one 3/8" X 4-1/2"
Hex Bolt (130), two 3/8" Washers (152) and one 3/8" Nut (159).
2. Attach the Leg Extension Arm (13) to the Seat Frame (8) by aligning holes and then inserting the Leg
Extension Axle (74). Fasten the Leg Extension Axle (74) using two 5/16" Washers (154), two 5/16" Spring
Washers (155) and two 5/16" X 5/8" Inner Hex Screw (141).
3. Insert two 3/4" Steel Bushings (107) into the holes in the Leg Extension Arm (13). Attach the Left and
Right Leg Extension Arms (38 & 39) to the Leg Extension Arm (13) by tightening the 5/16" X 1/2" Set
Screw (148A). Moisten the center of two Foam Pads (80) and slide onto each end of the Left and Right
Leg Extension Arms (38&39). Attach Plastic Washer (103) to both side of Cover of Foam Pads (80) and
secure the Pads with Plastic Cover (103A) using 5/16" X 1-1/4" Sunken Head Screw (142).
4. Attach the Seat Pad (67) to the Chromed Seat Adjuster (9), using two 3/8" X 1-3/4" Hex Bolts (135) and
two 3/8" Washers (152). Then insert the Chromed Seat Adjuster (9) into the Seat Frame (8). Pull the
Spring Knob (112) out to adjust the Chromed Seat Adjuster (9) to your desired height.
5. Insert a Foam Roller Holder (71) into the tube on the front of the Chromed Seat Adjuster (9). Moisten the
center of two Foam Pads (80) with
Holder (71). Attach Plastic
(80) and secure the Pads with
Sunken Head Screw (142).
6. Attach the Back Pad Adjuster
3/8" X 3-1/8" Hex Bolt (130A),
(159). It may be necessary
Adjuster (12) pivot freely.
Pad Adjuster (12) in place.
7. Slide Metal Hinge (40) to
Pad
Bolts
Foam
hole of Back Pad
Pads (80) with
Holder (71). Attach
of Cover of Foam
Pads (80) and secure the
Pads with Plastic Cover
(103A) using 5/16" X
1-1/4"
Sunken
Head
Screw (142).
Seat And Back Assembly
67
97
9
152
135
103
80
103A
135
159
8
154
142
152
112
155
131
141
152
130
39
103A 80
103
142
water and slide onto each end of the Foam Roller
Washer (103) to both side of Cover of Foam Pads
Plastic Cover (103A) using 5/16" X 1-1/4"
tighten this bolt, then loosen just to let Back Pad
Insert Pop Pin (113) to Front Upright (5) to hold Back
top of Back Pad Adjuster (12), then attach Back
(68) to Metal Hinge (40), using two 3/8" X 1" Hex
113
Adjuster (12). Moisten the center of Foam
water and slide onto each end of Foam Roller
5
152
103
71
148
80
103A
152
141
142
155
154
74
107A
107A
103
38
148A
101
13
101
11
(12) to the Front Upright (5), using one
two 3/8" Washers (152) and one 3/8" Nut
(136) and 3/8" Washers (152). Inserting
Roller Holder (71) through the bottom
Plastic Washer (103) to both side
159
40
136
152
136
152
12
71
142
152 148
152
130A
80
103
103A
142
80
103A
103A 142
80
103
68
159
152