Programming Your Controller - Rinnai Symmetry RDV3611 Operation Manual

Programming your controller

The clock must be set before the programmed timers will operate.
Each day of the week can be programmed for four periods, making a total of 28 programmed
periods.
Setting the clock
1. With the controller (heater)
off, press T for two seconds.
2. Using the UP and DOWN
buttons adjust to the correct
time. Ensure you have the
correct time of the day (AM/
PM). Press OK to accept.
3. Repeat process to adjust the
minutes and day of the week.
UP
OK
A/M T P PWR
DOWN
Week settings available
MO > TU > WE > TH > FR >
MO TU WE TH FR > SA > SU >
SA SU > MO TU WE TH FR SA SU
A weekday program can be set
so the program is used Monday
to Friday. Similarly, a weekend
program can be set for Saturday to
Sunday.
If you do nothing to change
the programming the default
settings would be available if you
set it to automatic mode. When
in this setting, the heater will
automatically turn itself on and off
depending on the temperatures
set (similar to an air conditioning
unit).
For example:
If the room temperature at 1 am
falls below 15 °C, the heater will
turn on and stay on until the room
temperature increases above 15°C.
12 | RDV3611 Operation Manual: 11158-A 01-12
DEFAULT SETTINGS
Time Start Temp.
°C
period time
20 °C
Period 1 6.00 am
15 °C
Period 2 8:30 am
21 °C
Period 3 5:00 pm
10:30 pm 15 °C
Period 4
If you would like to stop the
heater from coming on at all,
for example, during the night
and before period 1, you can
reduce the temperature setting
using the DOWN button until
–– °C is reached. This means
no set temperature has been
programmed, and your heater
will stay off until the next period
setting.
For example:
Time Start Temp.
°C
period time
20 °C
Period 1 5.30 am
15 °C
Period 2 8.00 am
20 °C
Period 3 5.30 pm
11:30 pm - - °C
Period 4
To revert back to the default
settings, press the following
sequence of buttons:
P > T > T > DOWN
To begin programming
With the controller off, press
and hold the 'P' button for two
seconds to initiate programming.
The LCD will display 'PROG',
'Pd' and the time at which the
controller is currently set will flash.
Period 1 can now be set.
Setting the day of the week
1. Press and release the 'UP' or
'DOWN' button to change
the day of the week. Scrolling
order is as follows:
MO > TU > WE > TH > FR
> SA > SU > SA SU > MO
TU WE TH FR SA SU
2. To accept the selected day(s)
of the week press OK.
Setting the period starting time
1. After setting the day the AM/
PM settings will flash. To set
the P1 starting time, press and
release the 'UP' or 'DOWN'
button for the hour setting.
Ensure that the AM/PM is set
correctly.
2. To accept press OK. The
minute setting will now flash
as in step 1—press OK to
accept.
Setting the temperature
1. After setting the time period
the temperature will flash.
Press and release the 'UP'
or 'DOWN' button for two
seconds to adjust.
2. To accept press 'OK' Period
.
one is now set for the day(s)
of the week you have chosen.
The LCD will display P2 to
indicate period 2, which can
now be set for the same day(s)
of the week.
3. Repeat programming process
for remaining periods.
If you want to check what has
been programmed, press P for
two seconds and select OK
continuously to cycle through the
settings for each period.