Table of Contents
Advertisement
Programming your controller
The clock must be set before the programmed timers will operate. Each day of the
week can be programmed for four periods.
Setting the clock
With the controller (heater) off,
press T for two seconds. Using
the UP and DOWN buttons set
the time. Ensure you have the
correct time of the day (AM/
PM). Press OK to accept.
Repeat process to adjust the
minutes and day of the week.
If after setting the clock you did
nothing else, the controller, if
set to operate in auto mode,
would operate using the default
settings.
DEFAULT SETTINGS
time
Start time temp. °C
period
Period 1
6.00 am
Period 2
8:30 am
Period 3
5:00 pm
Period 4
10:30 pm
In this setting the fire will
automatically turn itself on and
off based on the temperature
in the room, similar to an air
conditioning unit. For example;
if the room temperature at 1am
falls below 15 °C, the heater will
turn on and maintain the room
temperature at or close to
15 °C until the next programmed
period of 6am.
Typically we find people want
the fire to turn on in the
morning and then off a few
hours later, then on again in the
evening, and off when everyone
goes to bed. To do this you
would program the settings
something like this.
14 | Neo operation guide: 11907-E 05-14
time
period
Period 1
Period 2
Period 3
Period 4
In this setting the fire would
come on at 6am and heat
the room to 20 °C. It would
then turn off at 8am, come on
again at 5:30pm and turn off at
11:30pm.
* -- °C means no set temperature has
been programmed and the fire will
stay off until the next programmed
setting.
To revert to the default settings,
press the following sequence of
20 °C
buttons:
15 °C
P > T > T > DOWN
21 °C
to begin programming
15 °C
With the controller off,
press and hold the 'P' button
for two seconds to initiate
programming. The LCD will
display 'PROG', 'Pd' and the
time at which the controller is
currently set will flash. Period 1
can now be set.
Setting the day of the week
1. Press and release the 'UP'
or 'DOWN' button to
change the day of the week.
Scrolling order is as follows:
MO > TU > WE > TH > FR
> SA > SU > SA SU > MO
TU WE TH FR SA SU
2. To accept the selected
day(s) of the week press OK.
Start time temp. °C
6:00 am
20 °C
8.00 am
- - °C*
5.30 pm
20 °C
11:30 pm
- - °C*
Setting the period starting
time
1. After setting the day the
AM/PM settings will flash.
To set the P1 starting time,
press and release the 'UP' or
'DOWN' button for the hour
setting. Ensure that the AM/
PM is set correctly.
2. To accept press OK. The
minute setting will now flash
as in step 1—press OK to
accept.
Setting the temperature
1. After setting the time
period the temperature
will flash. Press and release
the 'UP' or 'DOWN' button
for two seconds to adjust.
Using the DOWN button
you can set the -- °C
mentioned previously.
2. To accept press 'OK'.
Period one is now set for
the day(s) of the week you
have chosen. The LCD will
display P2 to indicate period
2, which can now be set
for the same day(s) of the
week.
3. Repeat programming
process for remaining
periods.
If you want to check what has
been programmed, press P
for two seconds and select OK
continuously to cycle through
the settings for each period.
Advertisement
Table of Contents
