Table of Contents
Advertisement
X6$
= Port timeout (10‑sec. increments) 1 (= 10 seconds) – 65000 (default is 30 = 300 seconds = 5 minutes)
X6%
= SMNP port number
X6^
= SNMP contact name and location Up to 64 alphanumeric characters. Default = Not•Specified.
X6&
= SNMP community name
X6*
= Trap target
X6(
= SNMP trap version
X7)
= SNMP target 1 through 3
Command and Response Table for IP- and SNMP-Specific SIS Commands
Command Function
IP setup commands
Set matrix name
Read matrix name (location)
Reset matrix name to factory default
Set time and date
Read time and date
Set GMT offset
Example:
Read GMT offset
Set Daylight Saving Time
Read Daylight Savings Time
Set IP address
Read IP address
Read hardware address
Read # of open connections
Set subnet mask
Read subnet mask
Set gateway IP address
Read gateway IP address
Set administrator password
Read administrator password
Reset (clear) administrator
password
Set user password
Read user password
Reset (clear) user password
Set mail server, domainname
Read mail server, domainname
Set e‑mail recipient
Example:
Read e‑mail recipient
00000 (= disable) – nnnnn. Default = 00161. Leading zeroes are not necessary for entry.
Up to 64 alphanumeric characters.
Default = public (for read community) or private (for read‑write community).
1 – 3
2 or 3, or 0 = empty (default) if no target set
70 – 72 . 70 = SNMP target 1, ... 72 = target 3
SIS Command
Response
(Host to Unit)
(Unit to Host)
EX4)
}
CN
Ipn •
E
}
X4)]
CN
E
}
• CN
Ipn •
X4@
}
E
CT
Ipt
E
}
X4#]
CT
EX4$
}
CZ
Ipz
E
}
8.3CZ
Ipz+08:30
E
}
X4$]
CZ
EX4%
}
X4%]
CX
E
}
X4%]
CX
EX4^
}
CI
Ipi
E
}
X4^]
CI
E
}
X4&]
CH
E
}
X4*]
CC
EX4^
}
CS
Ips
E
}
X4^]
CS
EX4^
}
CG
Ipg
E
}
X4^]
CG
EX4(
}
Ipa •
CA
E
}
X4(]
CA
E
}
• CA
Ipa •
EX4(
}
CU
Ipu •
E
}
X4(]
CU
E
}
• CU
Ipu •
EX4^
X5)
X4(
}
,
,
CM
Ipm
E
}
X4^
CM
EX5!
X5@
}
,
CR
Ipr
E
69,Jsmith@folklore.netCR
Ipr69,Jsmith@folklore.net,
EX5!
}
X5@
CR
FOX Matrix 3200 and 7200 Switchers • Programming Guide
Additional description
X4)]
X4)]
" FOX-Matrix-3
3 pairs of the MAC address.
X4@]
X4$]
In the command, the divider between
hours and minutes can be either a
colon or a period. In the response, the
divider is a colon.
]
8 . 3 = 8:30
X4^]
Reads MAC address.
X4^]
X4^]
X4(]
]
X4(]
]
X4^
X5)
X4(]
,
,
X5)
X4(]
,
,
X5!
X5@
]
This command sets the e‑mail recipient.
,
,
To receive e‑mail notifications, you must
then set the events that the switcher
reports, using one or more separate
Set e-mail
next page).
}
]
]
,
( 7 )‑"
plus the last
(EM) SIS commands (on the
68
Advertisement
Table of Contents
