Page 1 Avaya Reference Guide P460 VAYA ULTILAYER ODULAR WITCH OFTWARE ERSION February 2003...
Page 3: Table Of Contents
Tree command ....................5 terminal width ....................6 terminal length ....................6 clear screen ....................7 Avaya P460 Sessions ..................... 8 Security Levels....................... 9 Entering the Supervisor Level ..............9 Entering the CLI ..................10 Entering the Technician Level ..............10 Getting Help......................
Page 10 Contents Layer 2 CLI Commands.................... 187 Layer 3 CLI Commands.................... 191 Glossary........................195 viii Avaya P460 Reference Guide...
Page 11: Chapter 1 Using The Cli
Enter. You can also configure your Avaya P460 using the P460 Manager with its graphical user interface. For details, see the "Device Manager" chapter in the User’s Guide that accompanies the switch and the Avaya MSNM P460 Device Manager User’s Guide...
Page 12: Conventions Used
Security level - used as the suffix of the prompt (Refer to Security Level on page 9.) • Application context - used as body of the prompt, this part is not mandatory. Example: Host name of the router is London Router is module number three Application context is OSPF Avaya P460 Reference Guide...
Page 13 For example, if after you want to set the system contact and the system name you must type both set system contact and set system name. However, you can use command abbreviations. Avaya P460 Reference Guide...
Page 14: Navigation, Cursor Movement And Shortcuts
For example, version can be abbreviated ver. For ambiguous commands, type the beginning letters on the command line and then use the Tab key to toggle through all the possible commands beginning with these letters. Avaya P460 Reference Guide...
Page 15: Universal Commands
Use the retstatus command to show whether the last CLI command you performed was successful. It displays the return status of the previous command. The syntax for this command is: retstatus Example:: P460-1# set port negotiation 2/4 disable Link negotiation protocol disabled on port 2/4. P460-1# Router(enable)# retstatus Succeeded...
Page 16: Terminal Width
- Set the new screen width in characters Example: P460-1> terminal width 80 terminal width: 80 terminal length Use the terminal length command to set the length of the terminal display. The syntax for this command is: terminal length [<screen-length>] screen-length none - Displays the current length in lines.
Page 17: Clear Screen
Chapter 1 Using the CLI clear screen Use the clear screen command to clear the current terminal display. The syntax for this command is: clear screen Example: P460-1> clear screen Welcome to P460 SW version 1.0.0 P460-1> Avaya P460 Reference Guide...
Page 18: Avaya P460 Sessions
Chapter 1 Using the CLI Avaya P460 Sessions You can use sessions to switch between P460 Supervisor modules or to switch between Layer 2 and Layer 3 commands in the P460 CLI. To switch between P460 modules use the command: session [<mod_num>] <mode>.
Page 19: Security Levels
SW version 1.0.0 Login: root Password:**** Password accepted. P460-1(super)# Defining new users Define new users and access levels using the username command in Supervisor Level. Exiting the Supervisor Level To exit the Supervisor level, type the command exit. Avaya P460 Reference Guide...
Page 20: Entering The Cli
For example, version can be abbreviated ver. For ambiguous commands, type the beginning letters on the command line and then use the TAB key to toggle through all the possible commands beginning with these letters. Avaya P460 Reference Guide...
Page 21: Router Configuration Contexts
Chapter 1 Using the CLI Router Configuration Contexts You can either use the general P460 commands available from the Router(configure)# prompt or you can enter one of two router configuration context modes: • Router interface context: This allows you to define parameters individually for each interface. To enter this context, type interface <interface_name>...
Page 22 Chapter 1 Using the CLI Avaya P460 Reference Guide...
Page 23: Chapter 2 Avaya P460 Cli Commands
Chapter 2 Avaya P460 CLI Commands This chapter describes all the P460 CLI commands and parameters in alphabetical order. area User level: read-write, admin. You can only access this command in Router-OSPF mode. Type router ospf at the command prompt to enter Router -OSPF mode if necessary.
Page 24: Arp Timeout
Chapter 2 Avaya P460 CLI Commands Use the arp command to add a permanent entry to the Address Resolution Protocol (ARP) cache. Use the no arp command to remove an entry, either static entry or dynamically learned. The syntax for this command is: [no] arp <ip-address>...
Page 25: Banner Login
Chapter 2 Avaya P460 CLI Commands Example: To set the arp timeout to one hour: Router-1(configure)# arp timeout 3600 To restore the default arp timeout: Router-1(configure)# no arp timeout banner login Use the banner login command to enter the login banner configuration mode.
Page 26: Clear Arp-Cache
Chapter 2 Avaya P460 CLI Commands clear arp-cache User level: read-write, admin. You can only access this command in configure mode. Type configure at the command prompt to enter configure mode. Use the clear arp-cache command to delete dynamic entries from the ARP cache and the IP route cache.
Page 27: Clear Dynamic Vlans
Chapter 2 Avaya P460 CLI Commands clear dynamic vlans User level: read-write, admin. Use the clear dynamic vlans command to clear dynamically learned VLANs. Only the VLANs learned by the switch from incoming traffic are cleared using this command. The syntax for this command is:...
Page 28: Clear Ip Route
IP address of the network, or specific host to be added destination IP address of the router mask Example: P460-1# clear ip route 134.12.3.0 255.255.255.0 Route deleted. clear ip route (Layer 3) User level: read-write, admin. You can only access this command in configure mode.
Page 29: Clear Port Mirror
Destination module number dest port Destination port number Example: P460-1# clear port mirror 9/2/10/4 this command will delete the port mirror entry - do you want to continue (Y/N)? Mirroring packets from port 9/2 to port 10/4 is cleared clear port static-vlan User level: read-write, admin.
Page 30: Clear Radius Authentication Server
Port range vlan num The VLAN to unbind from the port Example: P460-1# clear port static-vlan 3/10 5 VLAN 5 is unbound from port 3/10 clear radius authentication server User level: read-write, admin. Removes a primary or secondary RADIUS authentication server.
Page 31: Clear System-Log
Chapter 2 Avaya P460 CLI Commands Example: P460-1# clear snmp trap 192.168.173.42 SNMP trap deleted. clear system-log User level: read-write, admin. Use the clear system-log command to delete the log file of a Supervisor Module. The syntax for this command is: clear system-log [<module_number>]...
Page 32: Clear Vlan
Chapter 2 Avaya P460 CLI Commands clear vlan User level: read-write, admin. Use the clear vlan command to delete an existing VLAN and return ports from this VLAN to the default VLAN #1. When you clear a VLAN, all ports assigned to that VLAN are assigned to the default VLAN #1.
Page 33: Configure
IP address of the host Example: P460-1# copy l2-config tftp c:\p460\config 149.49.152.36 copy tftp EW_archive User level: read-write, admin. Use the copy tftp EW-archive command to download the P460 Manager application into the switch via TFTP. Avaya P460 Reference Guide...
Page 34: Copy Tftp L2-Config
If Avaya MultiService Network Manager is running, you do not require an additional TFTP server.. The syntax for this command is: copy tftp EW_archive <filename> <ip> filename P460 Manager image file name (full path) The IP address of the host Example: P460-1# copy tftp EW-archive c:\P460\switch1.cfg 192.168.49.10 copy tftp l2-config User level: read-write, admin.
Page 35: Copy Tftp Startup-Config
* it is recommended to exit from it before performing configuration * * download operations. ********************************************************************* copy tftp startup-config User level: read-write, admin. Copies the P460 configuration from the saved TFTP file to the Startup Configuration NVRAM. The syntax for this command is: copy tftp startup-config <filename> <ip> filename...
Page 36: Copy Tftp Sw_Imagea
This operation may take a few minutes... Please refrain from any other operation during this time. ********************************************************************* * If you are currently running the P460 Device Manager application, * * it is recommended to exit from it before performing configuration * * download operations.
Page 37: Default-Metric
This operation may take a few minutes... Please refrain from any other operation during this time. ********************************************************************* * If you are currently running the P460 Device Manager application, * * it is recommended to exit from it before performing configuration * * download operations.
Page 38: Enable Interface
Chapter 2 Avaya P460 CLI Commands The syntax for this command is: disable interface [outband | inband] outband Disables the outband interface inband Disables the inband interface Example: P460-1# disable interface outband You must reset the device in order for the change to take effect.
Page 39: Enable Vlan Commands
Chapter 2 Avaya P460 CLI Commands enable vlan commands User level: read-write, admin. You can only access this command in interface mode. Type interface [name] at the command prompt to enter interface mode. Use the enable vlans commands command before configuring VLAN- oriented parameters, when there is more than one interface on the same VLAN.
Page 40: Hostname (Layer 3)
Chapter 2 Avaya P460 CLI Commands Example: P460-1# hostname Session hostname is ‘P460’ P460-1# hostname “gregory” P460-1(super)# If you wish to enter a name which includes spaces, you must enclose the entire name in quotation marks, for example “new york”.
Page 41: Ip Access-Default-Action
Chapter 2 Avaya P460 CLI Commands The syntax for this command is: [no] interface <interface name> interface name String (up to 32 characters) Example: Router-1(configure)# interface marketing Done! Router-1(config-if:marketing)# If you wish to define a name which includes spaces, you must enclose the entire name in quotation marks, for example “new york”.
Page 42: Ip Access-List
Chapter 2 Avaya P460 CLI Commands Use the ip access-group command to activate a specific policy list. Use the no ip access-group command to deactivate the policy list. The syntax for this command is: [no] ip access-group <policy-list-number>[<default-action>] <priority-list-number> integer (100...199) <default-action>...
Page 43: Ip Access-List-Cookie
Chapter 2 Avaya P460 CLI Commands <source-ip> ip network <source-wildcard> ip network wildcard <operator> eq | lt | gt | range <port> integer (1...65535) <destination-ip> ip network <destination-wildcard> ip network wildcard <precedence> mandatory | optional] Example: Router-1(configure)# ip access-list 101 23 deny ip any 1.2.0.0 0.0.255.255...
Page 44: Ip Access-List-Name
Chapter 2 Avaya P460 CLI Commands necessary. Use the ip access-list-copy command to copy a configured source policy list to a destination policy list. The syntax for this command is: ip access-list-copy <source-list> <destination-list> <source-list> integer (100...199) <destination-list> integer (100...199)
Page 45: Ip Address
Chapter 2 Avaya P460 CLI Commands necessary. Use this command to set the owner for a specific policy list. The syntax for this command is: ip access-list-owner <policy-list-number> <owner> <policy-list-number> integer (100...199) <owner> list owner Example: Router-1> ip access-list-owner 101 admin...
Page 46: Ip Admin-State
Chapter 2 Avaya P460 CLI Commands ip admin-state User level: read-write, admin. You can only access this command in interface mode. Type interface [name] at the command prompt to enter interface mode. Use the admin-state command to set the administrative state of an IP interface.
Page 47: Ip Bootp-Dhcp Relay
Chapter 2 Avaya P460 CLI Commands allocated for bootp/dhcp requests: Router-1(configure-if:marketing) # ip bootp-dhcp network 192.168.169.0 Done! ip bootp-dhcp relay User level: read-write, admin. You can only access this command in configure mode. Type configure at the command prompt to enter configure mode if necessary.
Page 48: Ip Broadcast-Address
Chapter 2 Avaya P460 CLI Commands The syntax for this command is: ip bootp-dhcp server <ip-address> ip-address The IP address of the server. Example: To add station 192.168.37.46 as a bootp/dhcp server to handle bootp/dhcp requests arriving at the interface “marketing”: Router-1(configure-if:marketing) # ip bootp-dhcp server 192.168.37.46...
Page 49: Ip Default-Gateway
Chapter 2 Avaya P460 CLI Commands ip default-gateway User level: read-write, admin. You can only access this command in configure mode. Type configure at the command prompt to enter configure mode. Use the ip default-gateway command to define a default gateway (router).
Page 50: Ip Icmp-Errors
Chapter 2 Avaya P460 CLI Commands ip icmp-errors User level: read-write, admin. You can only access this command in configure mode. Type configure at the command prompt to enter configure mode if necessary. Use the icmp-error command to turn ICMP error messages on.
Page 51: Ip Max-Route-Entries
Chapter 2 Avaya P460 CLI Commands To restore the maximum number of ARP cache entries to its default: Router-1(configure)# no ip max-arp-entries ip max-route-entries User level: read-write, admin. The ip max-route-entries command exists for compatibility with Avaya™ P550. There is no limitation on the size of the routing table, except for the amount of available memory.
Page 52: Ip Netmask-Format
Chapter 2 Avaya P460 CLI Commands disable Netbios packets are not rebroadcasted into or out of this interface. Example: To enable rebroadcasting of netbios packets received by and sent from the interface “marketing”: Router-1(config-if:marketing)# ip netbios-rebroadcast both ip netmask-format User level: read-write, admin.
Page 53: Ip Ospf Authentication-Key
Chapter 2 Avaya P460 CLI Commands ip ospf authentication-key User level: read-write, admin. You can only access this command in Interface mode. Type interface [name] at the command prompt to enter Interface mode if necessary. Use the ip ospf authentication-key command to configure the interface authentication password.
Page 54: Ip Ospf Dead-Interval
Chapter 2 Avaya P460 CLI Commands ip ospf dead-interval User level: read-write, admin. You can only access this command in Interface mode. Type interface [name] at the command prompt to enter Interface mode if necessary. Use the ip ospf dead-interval command to configure the interval before declaring the neighbor as dead.
Page 55: Ip Ospf Priority
Chapter 2 Avaya P460 CLI Commands ip ospf priority User level: read-write, admin. You can only access this command in Interface mode. Type interface [name] at the command prompt to enter Interface mode if necessary. Use the ip ospf priority command to configure interface priority used in DR election.
Page 56: Ip Proxy-Arp
Chapter 2 Avaya P460 CLI Commands ip proxy-arp User level: read-write, admin. You can only access this command in interface mode. Type interface [name] at the command prompt to enter interface mode. Use the ip proxy-arp command to enables proxy ARP on an interface.
Page 57: Ip Rip Authentication Mode
Chapter 2 Avaya P460 CLI Commands Use the no ip rip authentication key command to clear the password. The syntax for this command is: [no] ip rip authentication key <password> The authentication string for the interface. Up to 16 characters are password allowed.
Page 58: Ip Rip Default-Route-Mode
Chapter 2 Avaya P460 CLI Commands ip rip default-route-mode User level: read-write, admin. You can only access this command in interface mode. Type interface [name] at the command prompt to enter interface mode if necessary. Use the ip rip default-route-mode command to enable learning of the default route received by the RIP protocol.
Page 59: Ip Rip Rip-Version
Chapter 2 Avaya P460 CLI Commands The syntax for this command is: [no] ip rip poison-reverse Example: Router-1(configure-if:marketing) # ip rip poison-reverse Done! ip rip rip-version User level: read-write, admin. You can only access this command in interface mode. Type interface [name] at the command prompt to enter interface mode if necessary.
Page 60: Ip Rip Split-Horizon
Chapter 2 Avaya P460 CLI Commands The syntax for this command is: ip rip send-receive <mode>[<default route metric>] mode talk-listen - Set RIP to receive and transmit updates on the interface. talkdefault-listen - Set RIP to receive updates on the interface and send only a default route.
Page 61: Ip Route
Chapter 2 Avaya P460 CLI Commands Example: Router-1(configure-if:marketing) # no ip rip split-horizon Done! ip route User level: read-write, admin. You can only access this command in configure mode. Type configure at the command prompt to enter configure mode. Use the ip route command to establish a static route.
Page 62: Ip Routing-Mode
Chapter 2 Avaya P460 CLI Commands Use the ip routing command to enable IP routing. Use the no ip routing command to disable the IP routing process in the device. By default, IP routing is enabled. The syntax for this command is:...
Page 63: Ip Vlan/Ip Vlan Name
Chapter 2 Avaya P460 CLI Commands necessary. Use the ip simulate command to check the policy for a simulated packet. The command contains the addressed list number, and the packet parameters. The syntax for this command is: ip simulate <access-list-number> [<priority>] [<dscp- value>]<source>...
Page 64: Ip Vrrp
Chapter 2 Avaya P460 CLI Commands ip vlan name <vlan-Name> Example: To specify VLAN developmental as the VLAN used by interface “products”: Router-1(config-if:marketing)# ip vlan name development If you wish to define a name which includes spaces, you must enclose the entire name in quotation marks, for example “new york”.
Page 65: Ip Vrrp Auth-Key
Chapter 2 Avaya P460 CLI Commands The syntax for this command is: [no] ip vrrp <vr-id> address <ip-address> vr-id Virtual Router ID (1-255) ip-address The IP address to be assigned to the virtual router. Example: To assign address 10.0.1.2 to virtual router 1: Router-1(configure-if:marketing) # ip vrrp 1 address 10.0.1.2...
Page 66: Ip Vrrp Preempt
Chapter 2 Avaya P460 CLI Commands Use the no ip vrrp override addr owner command to discard these packets. The syntax for this command is: [no] ip vrrp <vr-id> override addr owner vr-id Virtual Router ID (1-255) Example: Router-1(configure-if:marketing) # ip vrrp 1 override addr...
Page 67: Ip Vrrp Priority
Chapter 2 Avaya P460 CLI Commands Use the ip vrrp primary command to set the primary address that shall be used as the source address of VRRP packets for the virtual router ID. Use the no ip vrrp primary command to return to the default primary address for the virtual router instance.
Page 68: Ip Vrrp Timer
Chapter 2 Avaya P460 CLI Commands Example: To set the priority value for virtual router 1 to 10: Router-1(configure-if:marketing) # ip vrrp 1 priority 10 Done! Example: To set the virtual router simple password for virtual router 1 to abcd:...
Page 69: Network
Line number in the banner (1...24) string String to be displayed at the given line number (up to 80 characters) Example: P460-1(super)# line 5 “P460 CLI” Done! network User level: read-write, admin. You can only access this command in router-RIP mode.
Page 70: No Rmon Alarm
Use the no rmon history command to delete an existing RMON alarm entry. The syntax for this command is: no rmon alarm <Alarm Index> Alarm Index History index defined using rmon alarm command or P460 Manager. P460-1# no rmon alarm 1026 Avaya P460 Reference Guide...
Page 71: No Rmon Event
Use the no rmon event command to delete an existing RMON event entry. The syntax for this command is: no rmon event <Event Index> Event Index History index defined using rmon event command or P460 Manager. P460-1# no rmon event 1054 no rmon history User level: read-write, admin.
Page 72: Nvram Initialize
Chapter 2 Avaya P460 CLI Commands Example: P460-1(super)# no username john User account removed. If you wish to delete a name which includes spaces, you must enclose the entire name in quotation marks, for example “new york”. You cannot delete the default user account “root”.
Page 73: Ping
Chapter 2 Avaya P460 CLI Commands ping User level: read-only, read-write, admin. Use the ping command to send ICMP echo request packets to another node on the network. The syntax for this command is: ping [host[number]] host Host IP address/Internet address of route destination. If missing then the last host IP is used.
Page 74: Redistribute (Rip)
Chapter 2 Avaya P460 CLI Commands Example: Router-1 (configure router:ospf) # redistribute static redistribute (RIP) User level: read-write, admin. You can only access this command in router-RIP mode. Type router rip at the command prompt to enter router-RIP mode if necessary.
Page 75 Chapter 2 Avaya P460 CLI Commands Reset Supervisor module in slot 2 If the Supervisor modules are in Active/Standby configuration, resetting the active supervisor will cause the standby supervisor to take over and become active. The reset command will not work during configuration saving.
Page 76 Chapter 2 Avaya P460 CLI Commands P460-1(super)# reset chassis This command will reset the chassis *** Reset *** - do you want to continue (Y/N)? y Reseting chassis... P460-1(super)# Avaya P460 Boot Creation date: Jan 6 2003, 18:29:57 Press any key to stop auto-boot...
Page 77: Rmon Alarm
The instances in which the alarm will be activated. The possible parameters are: Rising, Falling, risingOrfalling. owner Owner name string. Example: P460-1# rmon alarm 1026 1.3.6.1.2.1.16.1.1.1.5.1026 60 delta rising-threshold 10000 1054 falling-threshold 10 1054 risingOrFalling gregory alarm 1026 was created successfully Avaya P460 Reference Guide...
Page 78: Rmon Event
Chapter 2 Avaya P460 CLI Commands rmon event User level: read-write, admin. Use the rmon event command to create an RMON event entry. The syntax for this command is: rmon event <Event Number> <type> description <description> owner <owner> event number This is the event index number of this entry.
Page 79: Rmon History
The owner name string. Example: P460-1# rmon history 1026 1026 3/2 30 buckets 20 owner amir history 1026 was created successfully If you wish to define a name which includes spaces, you must enclose the entire name in quotation marks, for example “new york”.
Page 80: Router Rip
Chapter 2 Avaya P460 CLI Commands router rip User level: read-write, admin. You can only access this command in configure mode. Type configure at the command prompt to enter interface mode. Use the router rip command to configure the Routing Information Protocol (RIP).
Page 81: Set Allowed Managers
When this feature is enabled, only those stations whose IP addresses are listed in the Allowed Managers table can access the device over Telnet, SNMP, or HTTP. The syntax for this command is: set allowed managers [enabled|disabled] Example: P460-1(super)# set allowed managers enabled Managers are enabled Avaya P460 Reference Guide...
Page 82: Set Allowed Managers Ip
Managers table IP address IP address to be added or remove Example: P460-1(super)# set allowed managers ip add 149.49.32.134 Ip was added to the table set arp-aging-interval User level: read-write, admin. Use the set arp-aging interval command to set the ARP table aging interval for gateways’...
Page 83: Set Arp-Tx-Interval
• bank-a to set the boot bank to A • bank-b to set the boot bank to B Example: P460-1# set boot bank A boot bank is A set broadcast storm control User level: read-write, admin. Use the set broadcast storm control command to enable or disable broadcast storm control.
Page 84: Set Broadcast Storm Control Threshold
In pps (packets per second) from 10 to 144,000 pps The default value is 500 Example: P460-1# set broadcast storm control threshold 1000 Done! set device-mode User level: read-write, admin. Use the set device-mode command to set the switch mode – Layer 2 or Router (Layers 2 and 3).
Page 85: Set Device-Mode (Layer 3)
(Layer 3) User level: read-write, admin. Use the set device-mode command to change the basic mode of operation of the P460 switch between Router and Layer 2 modes. The syntax for this command is: set device-mode <mode> mode...
Page 86: Set Inband Vlan
The syntax for this command is: set inband vlan <vlan_num> vlan_num The number of the VLAN. Example: P460-1# set inband vlan 1 Management VLAN number set to 1 set intelligent-multicast User level: read-write, admin. Use the set intelligent-multicast command to enable or disable the IP- multicast filtering application.
Page 87: Set Intelligent-Multicast Group-Filtering Delay Time
The syntax for this command is: set intelligent-multicast group-filtering-delay time <seconds> seconds The time in seconds. Example: P460-1# set intelligent-multicast group-filtering-delay time Done! set intelligent-multicast router port pruning time User level: read-write, admin. Use the set intelligent-multicast router port pruning time command to set aging time for router ports.
Page 88: Set Interface Inband
Example: To configure the inband interface on VLAN 1, IP address 1.1.1.1 and netmask 255.255.255.24: P460-1# set interface inband 1 1.1.1.1 255.255.255.24 This command will RESET the device *** Reset *** - do you want to continue (Y/N)? y set interface outband User level: read-write, admin.
Page 89: Set Interface Ppp
PPP interface IP parameters, exit modem mode, disconnect the PPP session, or reset the connected modem. You must configure an IP address and net-mask for the P460 before you can establish a PPP connection. The IP address is a dummy address that is shared between two peers, and must be taken from a subnet that is different from the agent’s IP sub-net.
Page 90 Disable PPP and enter terminal mode Disconnect the active PPP session. reset Reset the connected modem. Example: P460-1# set interface ppp reset PPP has reset the connected modem. Example: P460-1# set interface ppp enable Entering the Modem mode within 60 seconds...
Page 91: Set Ip Route
User level: read-write, admin. Use the set ip route command to adds a route to the IP routing table. You can configure from 1 to 10 default static gateways for a P460 switch. The syntax for this command is: set ip route <destination> <netmask> <gateway>...
Page 92: Set License
Avaya P460 CLI Commands set license User level: read-write, admin. Use the set license command to activate a licensed feature on a specific P460 chassis. For a full description of the Feature License and the installation procedure please refer to the Installation Guide provided with the Feature License.
Page 93: Set Outband Duplex
Full Specifies full-duplex transmission. Half Specifies half-duplex transmission Example: P460-1# set outband duplex full Ethernet Console interface set to full-duplex. set outband negotiation User level: read-write, admin. Use the set outbound negotiation command to enable or disable the link negotiation protocol on the Ethernet console port.
Page 94: Set Outband Speed
Enable link negotiation protocol. disable Disable link negotiation protocol. Example: P460-1# set outband negotiation enable Auto-negotiation for outband port set successfully set outband speed User level: read-write, admin. Use the set outband speed command to configure the speed of Ethernet Console port.
Page 95: Set Port Auto-Negotiation-Flowcontrol-Advertisement
Chapter 2 Avaya P460 CLI Commands set port auto-negotiation-flowcontrol-advertisement User level: read-write, admin. Use the set port auto-negotiation-flowcontrol-advertisement command to set the flowcontrol advertisement for a Gigabit port when performing autonegotiation. The syntax for this command is: set port auto-negotiation-flowcontrol-advertisement <module>/ <port>...
Page 96: Set Port Classification
MAC addresses in the switch. The syntax for this command is: set port classification [module/port] {regular | valuable} module port module/port range regular | valuable port classification Example: P460-1# set port classification 2/19 valuable Port 2/19 classification has been changed. Avaya P460 Reference Guide...
Page 97: Set Port Disable
You can also specify a range of ports separated by a dash, for example, 4/5-13 for ports 5 to 13 on module 4. Example: P460-1# set port disable 4/1 Port 4/1 disabled. set port duplex User level: read-write, admin.
Page 98: Set Port Enable
Set half-duplex transmission Example: To set port 1 on module 4 to full duplex: P460-1# set port duplex 4/1 full Port 4/1 set to full-duplex. set port enable User level: read-write, admin. Use the set port enable command to enable a port or a range of ports.
Page 99 Chapter 2 Avaya P460 CLI Commands | on | proprietary} receive Indicates whether the port can receive administrative status from a remote device. Available only for Gigabit Ethernet modules with negotiation set to off. send Indicate whether the local port can send administrative status to a remote device.
Page 100 Chapter 2 Avaya P460 CLI Commands P460-1# set port flowcontrol receive 5/1 on Port 5/1 flow control receive administration status set to on (port will require far end to send flowcontrol) P460-1# set port flowcontrol send 5/1 off Port 5/1 flow control send administration status set to off...
Page 101: Set Port Level
You can also specify a range of ports separated by a dash, for example, 4/5-13 for ports 5 to 13 on module 4. value Priority level (0-7) Example: P460-1# set port level 3/1 5 Port 3/1 level set to 5 Avaya P460 Reference Guide...
Page 102: Set Port Mirror
Keyword to copy only incoming traffic both Keyword to copy both incoming and outgoing traffic Example: P460-1# set port mirror source-port 3/9 mirror-port 4/10 direction both Mirroring both Rx and Tx packets from port 3/9 to port 4/10 is enabled...
Page 103: Set Port Name
Name (up to 16 characters) Example: P460-1# set port name 4/21 arthur Port 4/21 name set. If you wish to define a name which includes spaces, you must enclose the entire name in quotation marks, for example “new york”.
Page 104: Set Port Redundancy
Disable port negotiation protocol Example: To disable autonegotiation on port 1, module 4: P460-1# set port negotiation 4/1 disable Link negotiation protocol disabled on port 4/1. set port redundancy User level: read-write, admin. Use the set port redundancy command to globally enables or disable the redundancy pairs you have defined.
Page 105: Set Port Redundancy-Intervals
Name for the redundancy scheme (Optional) Example: P460-1# set port redundancy 3/7 4/12 on red1 red1: Port 2/12 is redundant to port 1/7. Port redundancy is active - entry is effective immediately If you wish to define a name which includes spaces, you must enclose the entire name in quotation marks, for example “new york”.
Page 106: Set Port Spantree
The system switches bank only if the secondary link fails. Example: P460-1# set port redundancy-intervals 100 20 set port spantree User level: read-write, admin. Use the set port spantree command to enable or disable the spanning tree mode for specific switch ports.
Page 107: Set Port Spantree Priority
Number representing the cost. The cost level is set from 1 to 65535. A lower cost (lower value) specifies precedence of a port to forward traffic. Example: P460-1> set port spantree cost 4/2 4096 port 4/2 spantree cost is 4096 set port spantree priority User level: read-write, admin.
Page 108: Set Port Static-Vlan
4/5-13 for ports 5 to 13 on module 4. Example: To configure port 1 on module 4 to 100 Mbps P460-1# set port speed 4/1 100MB Port 4/1 speed set to 100 Mbps. set port static-vlan User level: read-write, admin.
Page 109: Set Port Trap
Chapter 2 Avaya P460 CLI Commands Example: P460-1# set port static-vlan 3/4-6 2 VLAN 2 is bound to port 3/4 VLAN 2 is bound to port 3/5 VLAN 2 is bound to port 3/6 set port trap User level: read-write, admin.
Page 110: Set Port Vlan-Binding-Mode
Number of the port on the module. You can also specify a range of ports separated by a dash, for example, 4/5-13 for ports 5 to 13 on module 4. Example: P460-1# set port vlan 2 3/5 VLAN 2 modified. VLAN Mod/Ports ---- ---------------------------...
Page 111: Set Ppp Authentication Incoming
Chapter 2 Avaya P460 CLI Commands Example: P460-1# set port vlan-binding-mode 5/5-9 static Set Port vlan binding method:5/5 Set Port vlan binding method:5/6 Set Port vlan binding method:5/7 Set Port vlan binding method:5/8 Set Port vlan binding method:5/9 set ppp authentication incoming User level: read-write, admin.
Page 112: Set Ppp Chap-Secret
The syntax for this command is: set ppp chap-secret <chap-secret> chap-secret The shared secret, 4 to 32 characters. Example: P460-1(super)# set ppp chap secret hush PPP shared secret for CHAP authentication is set Avaya P460 Reference Guide...
Page 113: Set Ppp Incoming Timeout
The syntax for this command is: set ppp incoming timeout <time> time The timeout in minutes Example: P460-1# set ppp incoming timeout 15 PPP incoming session will automatically disconnect after 15 minutes of idle time set qos dscp-agg-index User level: read-write, admin.
Page 114: Set Qos Dscp-Name
Chapter 2 Avaya P460 CLI Commands necessary. Use the set qos dscp-cos-map command to configure the DSCP table. The syntax for this command is: set qos dscp-cos-map <dscp1>[-<dscp2>] <operation> [<precedence>] dscp1 dscp range min (0-63) dscp dscp range max (0-63)
Page 115: Set Qos Trust
Use the set qos trust command to configure which of the incoming packet's priority parameters should be considered when determining the new assigned priority. You can configure the P460 to trust either the cos (the 802.1p priority), the dscp (the DSCP value), or neither. The default value is trust-cos.
Page 116: Set Radius Authentication Retry-Time
<number> number Number of retries Example: P460-1(super)# set radius authentication retry-number 3 set radius authentication retry-time User level: read-write, admin. Sets the time to wait before re-sending an access request. The syntax for this command is: set radius authentication retry-time <time>...
Page 117: Set Radius Authentication Secret
The syntax for this command is: set radius authentication secret <string> text password string Example: P460-1(super)# set radius authentication secret hush P330-N(super)# set radius authentication server User level: read-write, admin. Sets the IP address (and shared secret) of the primary or secondary RADIUS Authentication server.
Page 118: Set Slot Power
RADIUS server used port number 1645. The syntax for this command is: set radius authentication udp-port <number> Example: P460-1(super)# set radius authentication udp-port number 1645 set slot power User level: read-write, admin. Use the set slot power command to power up or power down a slot. If there is a module in the slot, then the command will reset the device.
Page 119: Set Snmp Community
Chapter 2 Avaya P460 CLI Commands Example 2 – if there is a module in the slot:: P460-1> set slot power 4 up This command will RESET the device *** Reset *** - do you want to continue (Y/N)? Y Module in slot 4 is shutting down.
Page 120: Set Snmp Retries
User level: read-write, admin. Use the set snmp retries command to set the number of retries initiated by the P460 Manager when it tries to send SNMP messages to the switch. The syntax for this command is: set snmp retries <number>...
Page 121 IP address or IP alias of the system to receive SNMP traps Example: To enable SNMP ConfigChange traps to a specific manager: P460-1# set snmp trap 192.168.173.42 enable config SNMP config change traps enabled. Example: To enable all traps to a specific manager: P460-1# set snmp trap 192.168.173.42 enable all...
Page 122: Set Snmp Trap Auth
SNMP traps upon SNMP authentication failure. The syntax for this command is: set snmp trap {enable|disable} auth Example: P460-1# set snmp trap enable auth Authentication trap enabled set spantree enable/disable User level: read-write, admin. Use the set spantree command to enable or disable the spanning-tree algorithm for the switch.
Page 123: Set Spantree Priority
• The contact name string should be typed inside inverted commas. • The name is cleared if you leave this field blank. Example: P460-1(super)# set system contact “gregory kohll” *** Set system contact *** system contact set set system location User level: read-only, read-write, admin.
Page 124: Set System Name
• The location is cleared if you leave this field blank. Example: P460-1# set system location “tech-support” *** Set system location *** system location set If you wish to enter a name which includes spaces, you must enclose the entire name in quotation marks, for example “new york”.
Page 125: Set Time Client
Enable periodic network time acquisition disable Disable periodic network time acquisition Example: P460-1# set time client enable Time client mode enabled set time protocol User level: read-write, admin. Use the set time protocol command to set the protocol for use in the system as either SNTP protocol or TIME protocol.
Page 126: Set Time Server
<ip address> ip address IP address of the TIME server. Example: P460-1# set time server 192.49.53.68 The Server Ip has been set to 192.49.53.68 set timezone User level: read-write, admin. Use the set timezone command to assign a timezone name and sets the time difference of the device relative to the Coordinated Universal Time (UTC / GMT).
Page 127: Set Vlan
Example: P460-1# set vlan 3 name gregory VLAN id 3, vlan-name gregory created. If you wish to define a name which includes spaces, you must enclose the entire name in quotation marks, for example “new york”.
Page 128: Set Vlan (Layer 3)
Web access to the device. The syntax for this command is: set web aux-files-url <//IP address/directory name> Example: P460-1# set web aux-files-url //192.168.47.25/emweb-aux- files If you wish to define a directory name which includes spaces, you must enclose the Avaya P460 Reference Guide...
Page 129: Show Access-Group
Use the show allowed managers status command to display the activation status of the Allowed Managers feature. The syntax for this command is: show allowed managers status Example: P460-1(super)# show allowed managers status Managers are disabled. Avaya P460 Reference Guide...
Page 130: Show Allowed Managers Table
Use the show allowed managers table to display the list of the twenty possible allowed managers IP addresses. The syntax for this command is: show allowed managers table Example: P460-1(super)# show allowed managers table 1 ) 149.49.32.134 2 ) Not Used 3 ) Not Used 4 ) Not Used...
Page 131: Show Arp-Tx-Interval
Chapter 2 Avaya P460 CLI Commands Example: P460-1> show arp-aging-interval ARP table aging interval for gateways was set to 10 minutes. show arp-tx-interval User level: read-only, read-write, admin. Use the show arp-tx-interval command to display the keep-alive frames transmission interval.
Page 132: Show Cam
Chapter 2 Avaya P460 CLI Commands settings. The syntax for this command is: show broadcast storm control Example: P460-1> show broadcast storm control Broadcast Threshold Storm Control ---------------- ------------ disable show cam User level: read-only, read-write, admin. Use the show cam command to display the CAM table entries for a specific module and port.
Page 133: Show Cam Mac
Chapter 2 Avaya P460 CLI Commands Example: P460-1> show cam Total Matching CAM Entries Displayed = 128 Dest MAC/Route Dest vlan Destination Ports ------------------- ---- ----------------- 08:00:20:c6:98:5f 3/33 08:00:20:c4:c8:51 3/33 00:00:3b:80:49:7c 3/33 00:00:5e:00:01:01 3/33 00:00:5e:00:01:02 3/33 00:01:02:de:96:2f 3/33 00:02:2d:47:18:67 3/33...
Page 134 Chapter 2 Avaya P460 CLI Commands vlan VLAN identity Example: P460-1> show cam mac 00-00-81-01-23-45 Dest MAC/Route Destination Ports vlan -------------- ----------------- ----- 00-00-81-01-23-45 00-00-81-01-23-46 Total Matching CAM Entries = 2 Avaya P460 Reference Guide...
Page 135: Show Chassis-Identity
P460-1> show cpu load The current CPU utilization is 1% show cs User level: read-only, read-write, admin. Use the show cs command to show the version numbers of the P460 chassis and installed components. The syntax for this command is: show cs...
Page 136: Show Dscp
Chapter 2 Avaya P460 CLI Commands Example: P460-1> show cs Chassis : 0.3 Fans : n/a Psu_1 : n/a Psu_2 Psu_3 Slot Type ---- ------------------------- -------- Avaya P460-M460ML-SPV Avaya P460-M4648ML-T-2G Avaya P460-M4612ML-G show dscp User level: read-only, read-write, admin. Use the show dscp command to display the DSCP table.
Page 137: Show Device-Mode
Chapter 2 Avaya P460 CLI Commands Example: Router-1> show dscp set qos trust trust-cos-dscp DSCP ActionAgg Idx Name ---- ------------- --------------------------------------- fwd0 DSCP #0 fwd0 DSCP #1 fwd0 DSCP #2 fwd0 DSCP #3 fwd0 DSCP #4 fwd0 DSCP #5 fwd0...
Page 138: Show Environment Fans
Chapter 2 Avaya P460 CLI Commands The syntax for this command is: show dynamic vlans Router-1> show dynamic vlans VLAN NAME VLAN ID VLAN MAC ---------------- ------- ----------------- Default 1 02:e0:3b:1d:f9:01 show environment fans User level: read-only, read-write, admin. Use the show environment fans command to display the current fans status for the switch.
Page 139: Show Event-Log
Chapter 2 Avaya P460 CLI Commands The syntax for this command is: show environment power Example: P460 > show environment power PSU1 Capacity: 300 Watts (48V @ 6.25 Amps) PSU2 Capacity: none PSU3 Capacity: none PSUs Configuration: 1 PSU/s , no redundancy.
Page 140: Show Intelligent-Multicast
Chapter 2 Avaya P460 CLI Commands show intelligent-multicast User level: read-only, read-write, admin. Use the show intelligent-multicast command to display the intelligent multicast configuration. The syntax for this command is: show intelligent-multicast Example: P460-1> show intelligent-multicast Intelligent-multicast configuration: ------------------------------------ intelligent-multicast state ---------------------- Disabled...
Page 141: Show Ip Arp
Chapter 2 Avaya P460 CLI Commands The syntax for this command is: Show ip access-lists[<policy-list-number>] policy-list-number The policy list number (integer from 100 to 199) Example: Router-1> show ip access-lists ip access-list 100 10 deny-and-notify tcp 192.168.55.0 0.0.0.255 range 5000...
Page 142: Show Ip Icmp
Chapter 2 Avaya P460 CLI Commands Example: show ip arp Display all ARP mapping show ip arp marketing Display interface ARP mapping show ip arp 192.168.49.1 Display one host ARP mapping show ip arp 192.168.49.1 255.255.255.0 Display range of ARP mapping...
Page 143: Show Ip Ospf
Chapter 2 Avaya P460 CLI Commands Example: Router-1> show ip interface Showing 2 Interfaces mgmt is administratively up On vlan Default Internet address is 10.49.54.14 , subnet mask is 255.255.255.0 Broadcast address is 10.49.54.255 Directed broadcast forwarding is disabled Proxy ARP is disabled...
Page 144: Show Ip Ospf Interface
Chapter 2 Avaya P460 CLI Commands The syntax for this command is: show ip ospf database [{asbr-summary|router|network|network-summary|external}] asbr-summary Displays information only about the autonomous system boundary router summary LSAs. Optional. external Displays information only about the external LSAa. Optional. network Displays information only about the network LSAa.
Page 145: Show Ip Ospf Neighbor
Chapter 2 Avaya P460 CLI Commands show ip ospf neighbor User level: read-only, read-write, admin. Displays OSPF-neighbor information on a per-interface basis. The syntax for this command is: show ip ospf neighbor [<interface-name>] [<neighbor-id>] interface-name The OSPF interface name. neighbor-id Neighbor ID.
Page 146: Show Ip Reverse-Arp
Chapter 2 Avaya P460 CLI Commands show ip reverse-arp User level: read-only, read-write, admin. Use the show ip reverse-arp command to display the IP address of a host, based on a known MAC address. The syntax for this command is: show ip reverse-arp <mac addr>...
Page 147: Show Ip Route (Layer 3)
Chapter 2 Avaya P460 CLI Commands Example: P460-1> show ip route Destination MaskGateway ------------- -------------------------- 2.2.2.2 255.255.255.01.1.1.2 2.2.2.2 255.255.0.01.1.1.3 0.0.0.0 0.0.0.00.0.0.0 0.0.0.0 0.0.0.00.0.0.0 0.0.0.0 0.0.0.00.0.0.0 0.0.0.0 0.0.0.00.0.0.0 0.0.0.0 0.0.0.00.0.0.0 0.0.0.0 0.0.0.00.0.0.0 0.0.0.0 0.0.0.00.0.0.0 0.0.0.0 0.0.0.00.0.0.0 0.0.0.0 0.0.0.00.0.0.0 show ip route (Layer 3) User level: read-only, read-write, admin.
Page 148: Show Ip Route Static
Chapter 2 Avaya P460 CLI Commands Example: Router-1> show ip route best-match 199.93.0.0 Searching for: 199.93.0.0 Showing 1 rows Network Mask Interface Next-Hop Cost TTL Source --------------- ------------------------------------------------ ----- 199.93.0.0 255.255.0.0 e-135new 135.64.76.1 STAT-HI show ip route static User level: read-write, admin.
Page 149: Show Ip Unicast Cache
Chapter 2 Avaya P460 CLI Commands Example: Router-1> sh ip route summary IP Route Summary: Current number of routes: 69 show ip unicast cache User level: read-write, admin. Use the show ip unicast cache command to list the entries in the hardware unicast cache database.
Page 150: Show Ip Unicast Cache Networks
Chapter 2 Avaya P460 CLI Commands Example: Router-1> show ip unicast cache host Showing 6 hosts IP Address Next Hops MAC Address Port Sessions Number ========== =========== ================= ===== =============== 192.168.1.1 10.2.0.2 00.00.28.02.00.02 1/14 192.168.2.1 10.2.0.2 00.00.28.02.00.02 1/14 192.168.2.2 10.2.0.2 00.00.28.02.00.02...
Page 151: Show Ip Unicast Cache Networks Detailed
Chapter 2 Avaya P460 CLI Commands show ip unicast cache networks detailed User level: read-only, read-write, admin. Use the show ip unicast cache networks detailed command to list the networks and hosts that are handled by the hardware unicast cache database.
Page 152: Show Ip Unicast Cache Summary
Chapter 2 Avaya P460 CLI Commands show ip unicast cache summary User level: read-only, read-write, admin. Use the show command to display the number of host networks and next-hops in the module’s unicast cache. The syntax for this command is:...
Page 153: Show Ip Vrrp Detail
Chapter 2 Avaya P460 CLI Commands show ip vrrp detail User level: read-only, read-write, admin. Use the show ip vrrp detail command to display full VRRP-related information The syntax for this command is: show ip vrrp detail detail Show full detail information...
Page 154: Show L2-Config
Chapter 2 Avaya P460 CLI Commands Example: Router-1> show ip vrrp detail VRRP is globally enabled Virtual Router on VLAN: Router-id: State: MASTER Priority: Advertisement Interval: Last State Change: 00:00:00 Override Address Ownership Rule: No Authentication Type: None Authentication Key: ""...
Page 155 Chapter 2 Avaya P460 CLI Commands The syntax for this command is: show l2-config Example: P460-1> show l2-config !####################################################################### C H A S S I S I N F O !####################################################################### !# Upload time: UPTIME: 0:05:44.533 !# System description: Avaya Inc.- P460ML-SW Multi-layer Switch...
Page 156 Chapter 2 Avaya P460 CLI Commands !####################################################################### S P V I N F O !####################################################################### !# Slot #: !# SPV state: Active !# Blade type: Avaya P460-M460ML-SPV !# Blade-CS: !# Serial #: 0000009 !# SW versions - bank A, B: 1.0.5, 1.0.5...
Page 157 Chapter 2 Avaya P460 CLI Commands !####################################################################### I O B L A D E I N F O !####################################################################### !# Slot #: !# Blade type: Avaya P460-M4612ML-G --type q to quit or space key to continue-- !# Blade-CS: !# Serial #:...
Page 158 Chapter 2 Avaya P460 CLI Commands !#Set vlan table management parameters set vlan 1 name V1 !# Set the interface of the device !# set interface inband 1 149.49.50.233 255.255.255.0 !#Set PPP management parameters !#set interface ppp 0.0.0.0 0.0.0.0 --type q to quit or space key to continue--...
Page 159 Chapter 2 Avaya P460 CLI Commands !# set intelligent-multicast parameters set intelligent-multicast disable set intelligent-multicast client-port-pruning time 600 set intelligent-multicast router-port-pruning time 1800 set intelligent-multicast group-filtering-delay time 10 !#******* broadcast storm configuration ********* set broadcast storm control threshold 0 set broadcast storm control disable !#********************************************************* LINK AGGREGATION GROUP.
Page 160 Chapter 2 Avaya P460 CLI Commands !#*************** port 5/1 configuration ***************** !# Port type: Tranceiver Not Present !# Link status: no link !# STA status: Disabled !#********************************************************** set port disable 5/1 set port auto-negotiation-flowcontrol-advertisement 5/1 no-flowcontrol --type q to quit or space key to continue--...
Page 161 Chapter 2 Avaya P460 CLI Commands !#*************** port 5/3 configuration ***************** !# Port type: Tranceiver Not Present !# Link status: no link !# STA status: Disabled !#********************************************************** set port disable 5/3 set port auto-negotiation-flowcontrol-advertisement 5/3 no-flowcontrol set port negotiation 5/3 enable...
Page 162 Chapter 2 Avaya P460 CLI Commands !#*************** port 5/6 configuration ***************** !# Port type: Tranceiver Not Present !# Link status: no link !# STA status: Disabled !#********************************************************** set port disable 5/6 set port auto-negotiation-flowcontrol-advertisement 5/6 no-flowcontrol set port negotiation 5/6 enable...
Page 163 Chapter 2 Avaya P460 CLI Commands !#*************** port 5/9 configuration ***************** !# Port type: Tranceiver Not Present !# Link status: no link !# STA status: Disabled !#********************************************************** set port disable 5/9 set port auto-negotiation-flowcontrol-advertisement 5/9 no-flowcontrol set port negotiation 5/9 enable...
Page 164: Show License
Chapter 2 Avaya P460 CLI Commands !#*************** port 5/12 configuration ***************** !# Port type: Tranceiver Not Present !# Link status: no link !# STA status: Disabled !#********************************************************** set port disable 5/12 set port auto-negotiation-flowcontrol-advertisement 5/12 no-flowcontrol set port negotiation 5/12 enable...
Page 165: Show Logout
Chapter 2 Avaya P460 CLI Commands Example: P460-1> show license Application License Key State level -------------- ----------------------------- ------------- ------- smon 0000 0000 0000 0000 0000 0000 unlicensed routing licensed show logout User level: read-only, read-write, admin. Use the show timeout command to display the amount of time the CLI remains idle before timing out in minutes.
Page 166: Module Type
Chapter 2 Avaya P460 CLI Commands Example: P460-1> show module Type Status ---- ------------------------- ---- -------- ------ Avaya P460-Chassis 0000019 Avaya P460-M460ML-SPV 0000009 Active Empty Avaya P460-M4648ML-T-2G 0000027 Normal Empty Empty Empty PSU1 Avaya P460-PSU-300W Active PSU2 Avaya P460-PSU-300W Empty...
Page 167: Show Outband
Chapter 2 Avaya P460 CLI Commands show outband User level: read-only, read-write, admin. Use the show outband command to displays the Ethernet Console port status. This command applies to the specific supervisor module where you execute it. The syntax for this command is:...
Page 168: Show Port Auto-Negotiation-Flowcontrol-Advertisement
Chapter 2 Avaya P460 CLI Commands Show Port Output Fields Description Port Switch and port number Name Name of port Status Status of the port (connected, faulty, disabled) Vlan VLAN ID of the port Level Priority level of the port (0-7)
Page 169: Show Port Channel
Displays full information on the port Example: P460-1> show port channel Port Channel Status Channel Name and Id ---- --------------- ------------------- server1 server1 3/13 P460-1> show port channel 3/3 info Port Speed Duplex Vlan Port Trunk Vlan Priority status Binding...
Page 170: Show Port Classification
You can also specify a range of ports separated by a dash, for example, 4/5-13 for ports 5 to 13 on module 4. Example: P460-1> show port classification 4/8 Port Port Classification ------ --------------------- regular P460-1> show port classification 4/9...
Page 171 Number of the port on the module. If you do not specify a (Optional) number, all ports on the specified module are shown. Example: P460-1> show port flowcontrol 3/4 Port Send-Flowcontrol Receive-Flowcontrol Admin Oper Admin Oper ------ ----- ----...
Page 172: Show Port Mirror
Chapter 2 Avaya P460 CLI Commands show port mirror User level: read-only, read-write, admin. Use the show port mirror command to display mirroring information for the switch. The syntax for this command is: show port mirror Example: P460-1> show port mirror...
Page 173: Show Port Trap
You can also specify a range of ports separated by a dash, for example, 4/5-13 for ports 5 to 13 on module 4. Example: P460-1> show port trap 4/1 Port 4/1 up/down trap is disabled Avaya P460 Reference Guide...
Page 174: Show Port Vlan-Binding-Mode
Chapter 2 Avaya P460 CLI Commands show port vlan-binding-mode User level: read-only, read-write, admin. Use the show port-vlan-binding command to display port vlan binding mode information. The syntax for this command is: show port vlan-binding-mode [module[/port]] module Number of the module (3-6). If you do not specify a number, the ports on all the modules are shown.
Page 175: Show Ppp Baud-Rate
Chapter 2 Avaya P460 CLI Commands Example: P460-1> show ppp authentication PPP Authentication Parameters: ------------------------------ Incoming: CHAP show ppp baud-rate User level: read-only, read-write, admin. Use the show ppp baud-rate command to display the ppp baud-rate. The syntax for this command is:...
Page 176: Show Ppp Session
The syntax for this command is: show ppp incoming timeout Example: P460-1> show ppp incoming timeout PPP incoming timeout is 15 minutes show ppp session User level: read-only, read-write, admin. Use the show ppp session command to display PPP parameters and statistics of an active PPP session.
Page 177: Show Rmon Event
User level: read-only, read-write, admin. Use the show rmon event command to show the parameters of an Event entry defined by the rmon event command on Page 68 or using the P460 Manager. The syntax for this command is: show rmon event [<Event Index>]...
Page 178: Show Rmon History
History Index History index defined using rmon history command or RMON management tool Example: P460-1> show rmon history 1026 history Entry 1026 is active, owned by amir Monitors ifEntry.1.1026 every 30 seconds Requested # of time intervals, ie buckets, is 20...
Page 179: Show Secure Current
Chapter 2 Avaya P460 CLI Commands Example: P460-1> show rmon statistics Statistics for switch is active,owned by Monitor Monitors ifEntry.1.1026 which has Received 26375085 octets, 222536 packets, 154821 broadcast and 53909 multicast packets, 0 undersize and 0 oversize packets, 0 fragments and 0 jabbers,...
Page 180: Show Snmp
Chapter 2 Avaya P460 CLI Commands show snmp User level: read-only, read-write, admin. Use the show snmp command to display SNMP information. The syntax for this command is: show snmp Example: P460-1> show snmp Authentication trap disabled Community-Access Community-String ----------------...
Page 181: Show Snmp Retries
User level: read-only, read-write, admin. Use the show snmp retries command to display the number of retries initiated by the P460 Manager when it tries to send SNMP messages to the device. The syntax for this command is: show snmp retries Example: P460-1>...
Page 182 Chapter 2 Avaya P460 CLI Commands port Number of the port on the module. If you do not specify a (Optional) number, all ports on the specified module are shown. Example: P460-1> show spantree Spanning tree enabled Designated Root: 00-40-0d-88-06-c8...
Page 183: Show Spv
Chapter 2 Avaya P460 CLI Commands Output fields: Field Description Spanning tree Spanning-Tree Protocol status (enabled or disabled). Designated root MAC address of the designated spanning-tree root bridge Designated Root Priority of the designated root bridge. Priority Designated Root Cost Total path cost to reach the root.
Page 184 Chapter 2 Avaya P460 CLI Commands The syntax for this command is: show spv P460-1> show spv Chassis In-band MAC address : 00.04.0D.17.5A.00 Chassis Out-band MAC address : 00.04.0D.17.5A.FE Chassis Serial number : 0000007 Chassis CS : 0.3 SPV 1...
Page 185: Show System
Chapter 2 Avaya P460 CLI Commands show system User level: read-only, read-write, admin. Use the show system command to display the uptime, system name, location, contact person and MAC addresses. The syntax for this command is: show system Example: P460-1> show system...
Page 186 Chapter 2 Avaya P460 CLI Commands Example: P460-1> show system-log P460-1(super)# sh system-log --type q to quit or space key to continue-- *** UpTime : 0:37:19 *** *** MODULE : 1 *** System log file: H+n.AgDwZZioHgDZZZZ.(ioHgD3D3wD"bZZ.onD<ZZ2oAgDN~N}ZZAojgD gKgjiDZ!htllol ?glgi H+n.AgDwZZioHgDZZZZ.(ioHgD3D3wD@QZZ.onD3ZZ2oAgDlxi!hn95{s: !ZZAojgDb@3Z gKgjiDZoNs}E=ZH~YL{}Z?}s}= H+n.AgDwZZioHgDZZZZ.(ioHgD0D0TD0<ZZ.onD3ZZ2oAgDt((9(~;}EHN...
Page 187: Show System-Log (Layer 3)
Chapter 2 Avaya P460 CLI Commands show system-log (Layer 3) User level: read-only, read-write, admin. Displays the encrypted event log file. The syntax for this command is: show system-log [[slot]] slot Slot number (1...2) Avaya P460 Reference Guide...
Page 188: Show Time
Chapter 2 Avaya P460 CLI Commands show time User level: read-only, read-write, admin. Use the show time command to display the current P460 time and timezone. The syntax for this command is: show time Example: P460-1> show time 10:32:34 27 JAN 2000 GMT show time parameters User level: read-only, read-write, admin.
Page 189: Show Trunk
Chapter 2 Avaya P460 CLI Commands Example: P460-1> show timezone Timezone set to 'GMT', offset from UTC is 0 hours show trunk User level: read-only, read-write, admin. Use the show trunk command to display VLAN tagging information for the switch.
Page 190: Show Username
Chapter 2 Avaya P460 CLI Commands show username User level: admin. Use the show username command to display the local user accounts. The syntax for this command is: show username Example: P460-1(super)# show username User account password access-type ------------------------------- --------------------------------...
Page 191: Show Web Aux-Files-Url
Chapter 2 Avaya P460 CLI Commands The syntax for this command is: show vlan Example: Router-1> show vlan VLAN NAME VLAN ID VLAN MAC ---------------- ------- ----------------- Default 1 02:e0:3b:1d:f9:01 show web aux-files-url User level: read-only, read-write, admin. Displays the URL/directory from where the switch can access the Device Management auxiliary files (for example help files).
Page 192: Sync Time
Chapter 2 Avaya P460 CLI Commands Example: P460-1(super)# sync spv This command may overwrite the neighbor SPV software and reset it *** Confirmation *** - do you want to continue (Y/N)? y Copying Bank A to the neighbor SPV ...
Page 193: Traceroute
Chapter 2 Avaya P460 CLI Commands traceroute User level: read-only, read-write, admin. Provides a trace route utility. The syntax for this command is: traceroute <host> IP address. host Example: Router-1> traceroute 192.168.50.13 timers spf User level: read-write, admin. You can only access this command in Router-OSPF mode.
Page 194: Username
Chapter 2 Avaya P460 CLI Commands Use the validate-group command to verify that all the rules in a priority list are valid. If there is a configuration problem with a specific rule, or with a number of rules, detailed error messages will be given.
Page 195 Chapter 2 Avaya P460 CLI Commands Example: P460-1(super)# username john password johnny access-type read-write User account added. P460-1(super)# username root password secret access-type read-write ERROR: User account root has always an administrator access type. P460-1(super)# username root password secret access-type admin User account modified.
Page 196 Chapter 2 Avaya P460 CLI Commands Avaya P460 Reference Guide...
Page 197: Layer 2 Cli Commands
15 set ip route 81 no banner post-login 15 set license 82 no hostname 29 set logout 82 no rmon alarm 60 set outband duplex 157 no rmon event 61 set outband negotiation 83 Avaya P460 Reference Guide...
Page 198 162 set spantree priority 113 show port redundancy 162 set system contact 113 show port trap 163 set system location 113 show port vlan-binding-mode 164 set system name 114 show ppp authentication 164 Avaya P460 Reference Guide...
Page 199 175 show time 178 show time parameters 178 show timeout 155 show trunk 179 show username 180 show vlan 180 show web aux-files-url 181 sync spv 181 sync time 182 tech 182 terminal 6 username 184 Avaya P460 Reference Guide...
Page 200 Layer 2 CLI Commands Avaya P460 Reference Guide...
Page 201: Layer 3 Cli Commands
14 ip icmp-errors 40 no arp timeout 14 ip max-arp-entries 40 no default metric 27 ip max-route-entries 41 no icmp-error 40 ip netbios-rebroadcast 41 no interface 30 ip netmask-format 42 no ip access list 32 Avaya P460 Reference Guide...
Page 202 143 show logout 155 redistribute 63, 64 show module 155 reset 64 show snmp 170 router ospf 69 show snmp retries 171 router rip 70 show snmp timeout 171 router vrrp 70 show spv 173 Avaya P460 Reference Guide...
Page 203 Layer 3 CLI Commands show system-log 175 show time 178 show time parameters 178 show timezone 179 show vlan 180 show web aux-files-url 181 sync spv 181 timers spf 183 traceroute 183 validate-group 183 Avaya P460 Reference Guide...
Page 204 Layer 3 CLI Commands Avaya P460 Reference Guide...
Page 205: Glossary
A special control module that interfaces between the network manager and the managed devices, using the MIB as a management terms dictionary. Network Agents relay device events and execute instructions via embedded software. Alarm An audible or visible warning signal alerting designated management stations that Avaya P460 Reference Guide...
Page 206 This enables the workstation to boot without a hard or floppy disk drive. BPDU Bridge Protocol Data Unit. A packet that is transmitted at configurable intervals to exchange information among bridges in the network. Among other things, BPDUs Avaya P460 Reference Guide...
Page 207 The basic ATM transmission unit, consisting of a 53-byte packet (5-byte header and 48-byte payload). User traffic is segmented into cells at the source and reassembled at the destination. Cell Header The 5-byte ATM cell header contains control information regarding the destination path and flow control. Avaya P460 Reference Guide...
Page 208 IP address can even change while it is still connected. DHCP also supports a mix of static and dynamic IP addresses. Domain A group of computers and devices on a network that are administered as a unit with common rules and procedures. Avaya P460 Reference Guide...
Page 209 10 Mbps. A newer version of Ethernet, called 100Base-T (or Fast Ethernet), supports data transfer rates of 100 Mbps. The newest version, Gigabit Ethernet, supports data rates of 1 Gigabit per second. Avaya P460 Reference Guide...
Page 210 A circuit or device permitting data transmission in only one direction at a time between sending and receiving stations. For more information, refer to Duplex Mode on page 199. Half Duplex. A circuit or device permitting data transmission in only one direction Avaya P460 Reference Guide...
Page 211 Institute of Electrical and Electronics Engineers. Among other things, the IEEE develops standards for the computer and electronics industry. In particular, the IEEE 802 LAN standards are widely followed. IEEE 802.3 IEEE standard for Ethernet LANs. IEEE 802.5 IEEE standard for Token Ring LANs. Avaya P460 Reference Guide...
Page 212 A subnet mask is used to extract network and subnetwork information from the IP address. Internetwork Packet Exchange. A network layer protocol used for transferring data from servers to workstations. IPX is primarily used in Novell NetWare operating systems. Avaya P460 Reference Guide...
Page 213 ELAN. A LEC also provides a standard LAN service interface to any higher-layer entity that interfaces with the LEC. Each LEC is identified by a unique ATM address, and is associated with one or more MAC addresses reachable through that ATM address. Avaya P460 Reference Guide...
Page 214 MAC List. Metropolitan Area Network. A data communications network designed for a town or city. Usually characterized by high-speed connections using fiber optical cable or Avaya P460 Reference Guide...
Page 215 Network Management Station. A station that is responsible for managing all or part of a network. An NMS communicates with Network Agents to help keep track of network statistics and resources. Network Node Interface. Also known as Network-to-Network Interface. A standard Avaya P460 Reference Guide...
Page 216 Packet Internet Groper. Determines whether a specific IP address is accessible by sending a packet to the specified address and waiting for a reply. Plus Tagging A proprietary Avaya tagging mechanism that enables extended VLAN capabilities. Avaya P460 Reference Guide...
Page 217 Quality of Service. A measure of performance for a transmission system that reflects the system’s transmission quality and service availability. QoS is used mainly in connection with ATM media. Avaya P460 Reference Guide...
Page 218 A table stored in a router or other internetworking device that keeps track of routes to particular network destinations and, in some cases, metrics associated with those routes. Service Advertising Protocol. A protocol used to identify the services and addresses Avaya P460 Reference Guide...
Page 219 SMTP Simple Mail Transfer Protocol. Used to send E-mail messages between servers. Also used to send messages from a mail client to a mail server. Avaya P460 Reference Guide...
Page 220 Short for subnetwork. A subnet is a portion of a network that shares a common address component. On TCP/IP networks, a subnet includes all devices whose IP addresses have the same prefix. For example, all devices with IP addresses that start with 133.100.100 are part of the same subnet. Avaya P460 Reference Guide...
Page 221 Transceiver A device that both transmits and receives analog or digital signals. Usually used to describe the LAN component that applies signals onto the network wire and detects signals passing through the wire. Avaya P460 Reference Guide...
Page 222 VLAN Information Distribution Protocol. VIDP is a proprietary Avaya protocol running between Avaya P110 Device and Avaya M770 Device agents. A station’s VLAN information is distributed to all agents in order to use this information throughout the network. Avaya P460 Reference Guide...
Page 223 Virtual Path A group of virtual channels that can support multiple virtual circuits. Vendor-Specific Attribute. RADIUS supports attributes of which one, the VSA, supports vendor-specific attributes. This allows vendors to create custom RADIUS attributes. Avaya P460 Reference Guide...
Page 224 Glossary Avaya P460 Reference Guide...

Avaya P460 Reference Manual

Chapter 1 Using the CLI

Chapter 2 Avaya P460 CLI Commands

Quick Links

Related Manuals for Avaya P460

Summary of Contents for Avaya P460