Table of Contents
Advertisement
Effects
278
Delay
59: St. Mod Delay
(Stereo Modulation Delay)
This stereo delay uses an LFO to sweep the delay time. The pitch
also varies, creating a delay sound which swells and shimmers.
You can also control the delay time using a modulation source.
Stereo In - Stereo Out
Left
Delay
Delay
Right
D
-mod
Response
LFO: Tri / Sine
LFO Shape
LFO Sync
Modulation
a
LFO, D-mod
Mode
D-mod
L/R:+/+,
Modulation
L/R:+/–
b
Src
Off...Tempo
Response
0...30
LFO Waveform Triangle, Sine
c
LFO Shape
–100...+100
LFO Sync
Off, On
d
Src
Off...Tempo
LFO Frequency
e
0.02...20.00
[Hz]
MIDI Sync
Off, On
MIDI,
BPM
40.00...
f
300.00
Base Note
r...w
Times
x1...x32
L LFO Phase
–180...+180
[deg]
g
L Depth
0...200
R LFO Phase
–180...+180
[deg]
h
R Depth
0...200
L Delay Time
0.0...1000.0
[msec]
i
L Feedback
–100...+100
R Delay Time
0.0...1000.0
[msec]
j
R Feedback
–100...+100
-Wet, -
Wet/Dry
1:99...Dry...99:1
, Wet
k
Src
Off...Tempo
Amt
–100...+100
b: D-mod Modulation
When the modulation source is used for control, this parameter
reverses the left and right modulation direction.
FX Amt
Feedback
FX Amt
D-mod
L/R: +/+ +/–
LFO
Modulation Mode
LFO Phase
Switches between LFO modulation
control and modulation source
control
Reversed L/R control by modulation
source
Selects the modulation source that
controls delay time
Sets the rate of response to the
modulation source
Selects the LFO Waveform
Changes the curvature of the LFO
Waveform
Switches LFO reset off/on
Selects the modulation source that
resets the LFO
Sets the speed of the LFO
When this is on, the LFO speed is set
by BPM, Base Note, and Times,
instead of Frequency
MIDI syncs to the system tempo; 40–
300 sets the tempo manually for this
individual effect
Selects the type of notes that
specify the LFO speed
Sets the number of notes that
specify the LFO speed
Sets the phase obtained when the
left LFO is reset
Sets the depth of the left LFO
modulation
Sets the phase obtained when the
right LFO is reset
Sets the depth of the right LFO
modulation
Sets the delay time for the left
channel
Sets the feedback amount of left
delay
Sets the delay time for the right
channel
Sets the feedback amount of right
delay
Balance between the wet and dry
signal
Table , "Dynamic Modulation
sources, " on page 243
Amount of modulation source
d: LFO Sync
d: Src
g: L LFO Phase [deg]
h: R LFO Phase [deg]
If "LFO Sync" is On, the LFO will be reset by the modulation
source that is received.
The "Src" parameter sets the modulation source that resets the
LFO. For example, you can assign Gate as a modulation source
so that the sweep always starts from the specified point.
"L LFO Phase" and "R LFO Phase" set the phase obtained when
the left and right LFOs are reset. In this way, you can create
changes in pitch sweep for the left and right channels individu-
ally.
The effect is off when a value of the modulation source specified in
the "Src" parameter is 63 or smaller, and the effect is on when the
value is 64 or higher. The LFO is triggered and reset to the "L LFO
Phase" and "R LFO Phase" settings when the value changes from 63
or smaller to 64 or higher.
60: St. Dynamic Delay
(Stereo Dynamic Delay)
This stereo delay controls the level of delay according to the
input signal level. You can use this as a ducking delay that applies
delay to the sound only when you play keys at a high velocity or
only when the volume level is low.
Stereo In - Stereo Out
Left
High Damp Low Damp
Delay
Feedback
High Damp Low Damp
Delay
Right
FB
+
Envelope
Threshold
Control Target None, Out, FB
a
Polarity
+, –
Threshold
0...100
b
Offset
0...100
c
Attack
1...100
d Release
1...100
L Delay Time
e
0.0...1360.0
[msec]
R Delay Time
f
0.0...1360.0
[msec]
g Feedback
–100...+100
High Damp [%] 0...100
h
Low Damp [%] 0...100
i
Spread
–100...+100
Dry, 1:99...99:1,
Wet/Dry
Wet
j
Src
Off...Tempo
Amt
–100...+100
FX Amt
Spread
FX Amt
Out
Attack, Release
Control Target
Selects from no control, output, and
feedback
Reverses level control
Sets the level to which the effect is
applied
Sets the offset of level control
Sets the attack time of level control
Sets the release time of level control
Sets the delay time for the left
channel
Sets the delay time for the right
channel
Sets the feedback amount
Sets the damping amount in the
high range
Sets the damping amount in the low
range
Sets the width of the stereo image
of the effect sound
Balance between the wet and dry
signal
Table , "Dynamic Modulation
sources, " on page 243
Amount of modulation source
Advertisement
Table of Contents
