Table of Contents
Advertisement
Effects
274
Modulation and Pitch Shift (Mod./P.Shift)
value for the Feedback parameter, the pitch will be raised (or
lowered) more and more each time feedback is repeated.
If Feedback Position is set to Post, the feedback signal will not
pass through the pitch shifter again. Even if you specify a higher
value for the Feedback parameter, the pitch-shifted sound will
be repeated at the same pitch.
52: Pitch Shifter BPM
This pitch shifter enables you to set the delay time to match the
song tempo.
FX Amt = 100: Mono In - Mono Out / FX Amt = 0: Stereo In - Stereo Out
Left
Input Level
+
Pitch Shifter
Pre
Feedback Position
Input Level
Right
Tempo
BPM
Base Note x Times
BPM
Slow, Medium,
a
Mode
Fast
Pitch Shift [1/
–24...+24
2tone]
b
Src
Off...Tempo
Amt
–24...+24
Fine [cents]
–100...+100
c
Amt
–100...+100
MIDI,
BPM
40.00...
300.00
d
Time Over?
---, OVER!
Delay Base
r...w
Note
e
Times
x1...x32
Feedback
f
Pre, Post
Position
Feedback
–100...+100
g
High Damp [%] 0...100
Input Level
–100...+100
Dmod [%]
h
Src
Off...Tempo
Dry, 1:99...99:1,
Wet/Dry
Wet
i
Src
Off...Tempo
Amt
–100...+100
d: BPM
e: Delay Base Note
e: Times
The delay time is the duration of "Times" number of "Delay Base
Note" note values at the "BPM" tempo (or if "BPM" is set to
MIDI, the tempo determined by MIDI Clock).
d: Time Over?
You can set the delay time up to 5,290msec. If the delay time
exceeds this limit, the error message "OVER!" appears on the
display. Set the delay time parameters so that this message will
not appear. "Time Over?" is only a display parameter.
FX Amt
High Damp
Delay
Post
Feedback
FX Amt
Switches Pitch Shifter mode
Sets the pitch shift amount in steps
of a semitone
Selects the modulation source of
pitch shift amount
Sets the modulation amount of
pitch shift amount
Sets the pitch shift amount in steps
of one cent
Sets the modulation amount of
pitch shift amount
MIDI syncs to the system tempo; 40–
300 sets the tempo manually for this
individual effect
Displays an error message when the
delay time exceeds the upper limit
Selects the type of notes to specify
the delay time
Sets the number of notes to specify
the delay time
Switches the feedback
connection
Sets the feedback amount
Sets the damping amount in the
high range
Sets the modulation amount of the
input level
Selects the modulation source for
the input level
Balance between the wet and dry
signal
Table , "Dynamic Modulation
sources, " on page 243
Amount of modulation source
53: Pitch Shift Mod.
(Pitch Shift Modulation)
This effect modulates the detuned pitch shift amount using an
LFO, adding a clear spread and width to the sound by panning
the effect sound and dry sound to the left and right. This is espe-
cially effective when the effect sound and dry sound output from
stereo speakers are mixed.
FX Amt = 100: Mono In - Stereo Out / FX Amt = 0: Stereo In - Stereo Out
Left
+
Pitch Shifter
Right
LFO: Tri / Sqr
Pitch Shift
a
–100...+100
[cents]
b LFO Waveform Triangle,
Square
LFO Frequency
0.02...20.00
[Hz]
c
Src
Off...Tempo
–20.00...
Amt
+20.00
MIDI Sync
Off, On
MIDI,
BPM
40.00...
d
300.00
Base Note
r...w
Times
x1...x32
Depth
–100...+100
e
Src
Off...Tempo
Amt
–100...+100
L, 1 : 99...99 : 1,
f
Pan
R
Dry, 1:99...99:1,
Wet/Dry
Wet
g
Src
Off...Tempo
Amt
–100...+100
a: Pitch Shift [cents]
e: Depth
These parameters set the amount of pitch shift and amount of
modulation by means of the LFO.
Pitch
Original Pitch
g: Pan
h: Wet/Dry
The Pan parameter pans the effect sound and dry sound to the
left and right. With L, the effect sound is panned left, and the dry
sound is panned right. With a Wet/Dry = Wet setting, the effect
and dry sound will be output in a proportion of 1:1.
FX Amt
Pan
FX Amt
Sets the pitch difference from the
input signal
Selects the LFO Waveform
Sets the speed of the LFO
Selects a modulation source for LFO
speed
Sets the modulation amount of LFO
speed
When this is on, the LFO speed is set
by BPM, Base Note, and Times,
instead of Frequency
MIDI syncs to the system tempo; 40–
300 sets the tempo manually for this
individual effect
Selects the type of notes that
specify the LFO speed
Sets the number of notes that
specify the LFO speed
Sets the LFO modulation depth for
pitch shift amount
Selects the modulation source of
the depth of modulation
Sets the modulation amount of the
depth of modulation
Sets the panning effect sound and
dry sound separately
Balance between the wet and dry
signal
Table , "Dynamic Modulation
sources, " on page 243
Amount of modulation source
Pitch Shift Mod - Pitch Shift / Depth
LFO Waveform=Triangle
Depth (+value)
Pitch Shift (+ value)
LFO Waveform=Square
Depth (–value)
Advertisement
Table of Contents
